Vivo CART-V03E/W User manual

Multi-Purpose Mobile Podium
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/cart-v03e
SKU: CART-V03E/W
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x2)
Long Square
Tube
B (x2)
Short Square
Tube
C (x4)
Caster
D (x1)
Tube Connector
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly
or inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF CART.
• USE TIPOVER RESTRAINT OR ANCHOR CART TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
E (x1)
Tube Connector
Cover
F (x4)
M6 Socket Plate
G (x2)
Pole Set
H (x4)
Plastic Sleeve
I (x1)
Connecting
Tube
J (x2)
Plastic Knob
K (x2)
Shelf Support
L (x1)
Shelf
M (x1)
Top Plate
N (x1)
Right Connecting
Plate
O (x1)
Le Connecting
Plate
S-A (x4)
M6 Nut
P (x2)
Lever
Q (x2)
So Pad
S-B (x8)
M6x60mm
Bolt
S-C (x12)
M6x10mm
Screw
S-D (x4)
M4x6mm
Screw
S-E (x2)
M5x6mm
Set Screw
S-F (x2)
M6 Washer
T-A (x1)
2mm Allen
Wrench
T-B (x1)
4mm Allen
Wrench
T-C (x1)
5mm Allen
Wrench
T-D (x1)
Wrench

3
ASSEMBLY STEPS
STEP 2
Attach Plastic Sleeves (H) to Pole Set (G) as
shown. Slide the inner poles upward with
the plastic sleeves fitting inside the outer
poles, then extend the innser poles upward
until both shelf support holes are visible.
STEP 3
Attach the Long Square Tube (A) to the front of the
Tube Connector (D) and the Short Square Tube (B) to
the back of the Tube Connector (D) using M6x60mm
Screws (S-B), the M6 Socket Plate (F), and 5mm Allen
Wrench (T-C).
STEP 1
Attach Casters (C) to Short and Long Square
Tubes (A, B) using the provided Wrench (T-D).
Front
44 lbs
(20 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury. 22 lbs
(10kg)
TOP SHELF BOTTOM SHELF
T-D C
A
B
C
Back
Shelf
Support
Holes
TOOLS NEEDED
Phillips
Screwdriver
S-B
D
F
T-C
B
A
H
G

4
STEP 4
Mount Connecting Tube (I) to Pole Set (G) using M6x10 Screws (S-C) and 4mm Allen Wrench (T-B).
STEP 5
Aer making sure the poles are at the same height, insert Plastic Knobs (J) into the back of the Pole
Set (G) to set the height of the Inner Poles.
STEP 6
Slide Tube Connector Cover (E) over Pole Set (G). Attach Pole Set (G) to Tube Connector (D) using
M6x10mm Screws (S-C) and 4mm Allen Wrench (T-B) in the back, and M5x6mm Set Screws (S-E) and
2mm Allen Wrench (T-A) in the sides.
Left
Right
Front
J
G
E
D
G
S-E T-A
T-B
S-E
G
T-B
I
S-C

5
STEP 7
Attach Shelf Supports (K) to Pole Set (G) using M6x10 Screws
(S-C) and 4mm Allen Wrench (T-B).
STEP 8
Mount the Right and Le Connecting Plates (N, O) to the Top Plate (M) using M6 Nuts (S-A) and
tighten with the provided Wrench (T-D). The slots in the connecting plates must be facing towards the
front.
STEP 9
Attach the Shelf (L) to Shelf Supports (K) using M4x6mm Screws (S-D). Tighten with a Phillips
screwdriver.
Front
20
T-B S-C
K
G
S-D
L
K
S-D
N
O
T-D
M

6
STEP 10
Place the assembled top plate onto Pole Set (G), and secure with M6x10mm Screws (S-C) and 4mm
Allen Wrench (T-B).
STEP 11
Attach So Pads (Q) to the top front edge of the assembled top plate.
STEP 12
Insert Levers (P) with M6 Washers (S-F) through the slots in Connecting Plates (N, O) and screw into
Pole Set (G).
S-C
G
PS-F
O
G
N
Q

7
STEP 13
Loosen Levers (P) to adjust the tilt angle, then tighten in the desired position. Adjust the height by
loosening Plastic Knobs (J), then tighten at the desired height.
STEP 14
tilt 40˚
P
J

LAST UPDATED: 03/30/2023
REV2.1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303