Vivo STAND-TV08 User manual

TV Floor Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-tv08
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: STAND-TV08

2 3
PACKAGE CONTENTS
WARNING!
A (x1)
Pole with
Shelf
B(x1)
Base
C(x1)
VESA Plate
I (x1)
Bracket Cover
J (x2)
Cable Clip
K(x4)
M8x14
L (x1)
Wrench
H(x4)
Rubber Pad
E (x8)
M6x5
F (x2)
Le Arm
G (x2)
Right Arm
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
M(x1)
5mm Allen
Wrench
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
55lbs
(24.95kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
M-F (x4)
D5 Washer
M-G (x8)
D8 Washer
M-E (x4)
M8x50
M-A (x4)
M5x14
M-B (x4)
M6x14
M-D (x4)
M8x30
M-C (x4)
M6x30
D (x1)
Decorative
Cover
M-H (x8)
Spacer
Carefully ip base (B) upside down by holding
plastic tie. Place rubber pads (H) on corners of
base (B) as shown, turn base (B) right-side up,
and cut plastic tie.
STEP 2
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV CART.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
M-I (x8)
Spacer
Slide decorative cover (D) onto pole (A). Attach pole (A) to base (B) with M8x14 bolts (K) using 5mm
Allen wrench (N).
Scissors
A
M
D
B
K
M

4 5
STEP 3
Attach arms (F,G) to VESA plate (C) in desired position with M6x5 bolts (E).
STEP 4 STEP 5
Remove nut from bottom of VESA plate (C), then hang VESA plate over slot on top of pole
(A). Secure with the previously removed nut and tighten with wrench (L).
STEP 4 (Continued)
OPTION A: Flat Back TV
Attach VESA plates with arms (F,G) to back of
TV with screws (M-A or M-B) and washers (M-F
or M-G).
OPTION B: Curved Back TV
Attach VESA plates with arms (F,G) to back of TV
with screws (M-C, M-D, or M-E), washers (M-G),
and spacers (M-H or M-I).
E
300mm
400mm
300mm
400mm
400mm
200mm
E
TV
TV
TV
TV
TV
TV
M- C
M- D
M- H
M- G
M- C
M- D
M- I
M- G
M- C
M- D
M- I
M- G
M- H
M- E
M- I
M- G
M- E
M- I
M- G
M- H
M- E
M- I
M- G
M- H
M-A/M- B
M-F/M- G 1 2
3

6 7
STEP 5 (Continued) STEP 7
Adjust as Desired
Loosen the knobs as shown in the diagram to collapse the tray or adjust tray height.
STEP 6
Attach cover (I) to top of pole (A), and cable clips (J) to back.
L
L
I
J
J
+3°
-14°
+
3
°
-
3
°

Last Updated: 10/26/2018
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654