Vivo STAND-V012L User manual

Dual Monitor Extra Tall Desk Mount
with Laptop Holder
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v012l
SKU: STAND-V012L
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
a (x1)
Pole
b(x1)
Clamp
c(x1)
Clamp Brace
j (x1)
Support Plate
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
d(x1)
Swivel Arm
e(x3)
VESA Plate
f (x3)
M5x14
g (x2)
M8x12
h (x3)
Security Nut
i (x1)
M10 Bolt
k (x1)
M10 Washer
o (x1)
Allen Wrench
Set
l (x1)
Spring Washer
m (x1)
Grommet Base
Plate
n1 (x3)
Cable Clip
p (x1)
Wrench
t (x1)
Laptop Tray
q (x8)
M4x12
r (x8)
M4x30
s (x8)
M4 Spacer
u (x4)
M4x10 Bolt
v (x4)
M4 Nut
n2 (x6)
Cable Clip
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
w1 (x1)
Clamp Pad
w2 (x1)
Grommet Pad
d(x1)
Swivel Arm

3
22lbs
(9.98kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
PRE-ASSEMBLY
Remove the grub screws using the small Allen wrench (o). Thread the Poles (a) together as shown.
Re-install the grub screws using the small Allen wrench (o).
STEP 1
TOOLS NEEDED
Phillips
Screwdriver Drill
OPTION A: Clamp Installation
1. Install the “C” Clamp Brace (c) to the Pole (a)
using M5x14 Bolts (f), and tighten using the
small Allen wrench (o), see Figure 1.
2. Attach Clamp Pad (w1) to the “C” Clamp Brace
(c), see Figure 2.
3. Install the “C” Clamp (b) to the pole assembly
according to the thickness of the desktop. The
thickness can be changed to three positions.
Connect it using M8x12 Bolts (g), and tighten
using the medium Allen wrench (o). Tighten
the “C” Clamp (b) to the desktop using the
plastic knob, see Figure 3. NOTE: The “C”
Clamp (b) fits to the front of the “C” Clamp
Brace (c), with the M8x12 Bolts (g) passing
through the back and tightening into the “C”
Clamp in front.
g
o
b
Plastic Knob
a
c
f
Figure 1
Figure 3
w1
Figure 2
PER ARM

4
STEP 1 (Continued)
OPTION B: Existing Grommet Base Installation
1. If the existing grommet hole comes with a
plastic protector, remove it before installing
the desk mount. Install the Grommet Base
Plate (m) to the Pole (a) using M5x14 Bolts (f),
and tighten using the small Allen wrench(o),
see Figure 4.
2. Attach Grommet Pad (w2) to the Grommet
Base Plate (m), see Figure 5.
3. 3. Position the Pole (a) on the mounting
surface and secure using the Support Plate (j),
M10 Washer (k), Spring Washer (l) and M10
Bolt (i). Fasten the M10 Bolt using the Wrench
(p), see Figure 6.
j
i
k
l
a
m
f
Figure 4
Figure 6
w2 Figure 5
OPTION C: Self-Drilled Grommet Base Installation
1. Position the Pole (a) on the mounting surface
and mark the center hole. Drill a 3/8” (10mm)
diameter hole at the marked position through
the mounting surface. Install the Grommet
Base Plate (m) to the Pole (a) using M5x14
Bolts (f), and tighten using the small Allen
wrench (o), see Figure 7.
2. Attach Grommet Pad (w2) to the Grommet
Base Plate (m), see Figure 8.
3. Position the Pole (a) on the mounting surface
and secure using the Support Plate (j), M10
Washer (k), Spring Washer (l) and M10 Bolt (i).
Fasten the M10 Bolt using the Wrench (p), see
Figure 9.
j
i
k
l
a
m
f
Figure 7
Figure 9
w2 Figure 8

5
STEP 2
STEP 3
FOR LAPTOP
Attach VESA plate (e) to laptop tray (t) using
bolts (u) and M4 nuts (v).t
u
v
FOR FLAT BACK MONITOR
Attach VESA plate (e) to the monitor using
thumb screws (q).
q
Install Swivel Arms (d) to the Pole (a). Fasten the bolt on
each arm with the large Allen wrench (o). Attach the Wire
Clips (n1, n2) to the pole (a) and Swivel Arms (d).

6
STEP 3 (continued)
FOR CURVED BACK MONITOR
Attach VESA plate (e) to the monitor using bolts
(r) and spacers (s).
s
r
STEP 4
Slide the monitor onto the head of Swivel Arm (d) as shown in the diagram. Install the security
Nut (h). Make sure the security nut is installed before you rotate the monitor. Repeat for the laptop
tray (t).
h

7
STEP 5
STEP 6
If needed, tighten the tilt joint bolt with the medium Allen wrench (o) to fix the tilt angle. Use the
medium Allen wrench (o) to adjust the swivel joints as needed.
o
Manage cables using the wire clips
(n1, n2). Store tools in the wire
clips (n1).

LAST UPDATED: 06/17/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303