Vivo STAND-V003M User manual

Triple Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v003m
SKU: STAND-V003M
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
A (x1)
Arm
B(x1)
Pole
C(x2)
Side VESA Bracket
M-A (x12)
M4x12
M (x2)
M8x60
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Center VESA Bracket
E(x1)
Clamp
F (x1)
Grommet Base
G(x6)
Cable Clip
H (x1)
Cable Clip
L (x4)
Bushing
M-C (x12)
D5 Washer
M-B (x12)
M5x12
J (x5)
Rubber Pad
I (x1)
Pole Cover
K (x1)
Support
Plate
P (x1)
3mm Allen
Wrench
N (x4)
D8 Washer
O (x2)
M8 Nut
Q (x1)
5mm Allen
Wrench
R (x1)
6mm Allen
Wrench
S (x1)
Wrench

3
ASSEMBLY STEPS
STEP 1
OPTION A: Clamp Installation
Stick so pads (J) to bottom of clamp base (E). Slide cable management clip (H) and base cover (I)
on to bottom of pole (B). Thread pole (B) into clamp base (E), first loosening grub screws in the base
if needed. Tighten grub screws in clamp base (E) using 3mm Allen wrench (P). Secure clamp (E) to
desktop as shown in diagram.
TOOLS NEEDED
Phillips
Screwdriver
OPTION B: Grommet Base Installation
Remove screw from top of hand bolt in clamp (E), then remove hand bolt. Stick so pads
(J) to bottom of grommet base (F). Slide cable management clip (H) and base cover (I)
on to bottom pole (B). Thread bottom pole (B) into grommet base (F), first loosening grub
screws in the base if needed. Tighten grub screws in grommet base (F) using 3mm Allen
wrench (P). Slide support plate (K) over hand bolt and slide through grommet hole in
bottom of desktop. Thread into bottom of pole (B). If no grommet hole is present, drill hole
using 3/8” (10mm) drill bit.
17.6 lbs
(7.98 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER SCREEN

4
STEP 2
Place bushings (L) into holes at ends of arms (A). Place side VESA brackets (C) onto arms with M8x60
bolts. Secure with D8 washers (N) and M8 nuts (O), and tighten with 5mm Allen wrench (Q) and
wrench (S). Do not overtighten.
STEP 3
Slide arm (A) and center VESA bracket (D) over top of pole and tighten using 5mm Allen wrench (Q).

5
STEP 4
Attach cable management clips (G) to
arms (A) as shown.
STEP 5
Attach two bolts (M-A or M-B) and washers (M-C) to top mounting holes of monitor, making
sure to leave 3mm of threads exposed. Align bolts (M-A or M-B) in monitor over slots in
VESA plates. Secure using two more bolts (M-A or M-B) and washers (M-C) in the bottom
two holes of each monitor. Tighten all four bolts using Phillips screwdriver.

6
STEP 6
STEP 7
Store Allen wrenches (R, Q) in cable management clip (G) for future use.
Adjust tension in monitor bracket with 6mm allen wrench (R).

7
STEP 8
Adjust height of side monitors by turning bolt on top of each bracket with 5mm Allen wrench (Q) as
shown.

LAST UPDATED: 05/18/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303