Vivo STAND-V002V User manual

   
Instruction Manual
Email: [email protected]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
-   
 
phillips screwdriver
 
1
Scan the QR code with your mobile device or follow the link
to helpful videos and specifications related to this product.
 (x1)
Pole
 (x1)
Clamp
 (x2)
Arm wit VESA
Plate
 (x1)
Grommet Base
 (x1)
Bolt
 (x1)
Support Plate
(x1)
M1 Waser
! (x1)
Sprin Waser
" (x2)
Arm
# (x2)
Wire Co er
$ (x2)
Axis Co er
% (x2)
Stopper Rin
 (x6)
M4x6 Bolt
& (x2)
M1x1$ Bolt
 (x1)
Allen Wrenc
 (x8)
M4x3
(x8)
M4 Spacer
 (x2)
Cable Clip
 (x2)
M6x12 Bolt
' (x8)
M4x12 Tumb
Screw
( (x1)
Wrenc
- -)*++,, -.+*+ ,,

* 
Attach VESA plate arms (C) to arms (I) with screws (N) and axis covers
(K) as shown in diagram. Attach wire covers (J) with screws (M) as
shown in diagram. (Optional – Skip this step for shorter arms.)
* /
Slide one stopper ring (L) onto pole (A) and tighten at desired height
using allen wrench (P). Slide one assembled arm onto pole (A). Slide
second stopper ring (L) onto pole (A) and tighten at desired height
using allen wrench (P). Slide second assembled arm onto pole (A).
A
.01 *
2
* 2
&*  34 .* "
Attach pole (A) to clamp (B) at desired depth with bolts (O) using allen
wrench (P).
Remove clamp base and screws from
pole. Attach grommet base (D) to
pole (A) using previously removed
screws. Position the pole with base
on mounting surface and secure
using support plate (F), bolt (E), M10
washer (G) and spring washer (H). If
no grommet hole is present, drill 3/8”
(10mm) hole through the mounting
surface.
&*  ..  "

* 5
&*    
Attach monitors to VESA plates using thumb screws (Q).
&*  ,  
Attach monitors to VESA plates using screws (R) and spacers (S).
* 6
Remove cable covers from spring arms. Run cables through covers
and reinstall to arms. Install cable clips (T) to back of pole and
manage cables.
Adjust arm swivel joints by tightening or loosening grub screws on
each joint with small Allen Wrench (P).
3

* 7
Adjust arm tension by turning screw on top of center joint with large
Allen Wrench (P). Clockwise reduces tension, counter-clockwise
increases tension. The tension should be just enough to hold your
monitor in place without lifting itself up.
If you do not understand these directions, or if you have any
doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no
missing or defective parts. Improper installation may cause
damage or serious injury. Do not use this product for any
purpose that is not explicitly specified in this manual. We
cannot be liable for damage or injury caused by incorrect
assembly or inappropriate use.
Email: [e-mail]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
For more VIVO products, check out our
website at
www.vivo-us.com.
If any parts are received damaged or defective, please contact
us. We are happy to replace parts to ensure you have a fully
functioning product.
81 9
  
Last updated: 0 /23/18 4