Vivo MOUNT-PB1 User manual

Single Monitor Pegboard Panel Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-pb1
SKU: MOUNT-PB1
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
A (x1)
Mount Base
B(x2)
Mounting
Prongs
C(x1)
VESA Plate
S-A (x1)
M6x10mm
Screw
S-B (x4)
M4x8mm
Screw
M-A (x4)
M4x12mm
Screw
M-B (x4)
M4x16mm
Screw
M-C (x4)
M5x12mm
Screw
M-D (x4)
M5x16mm
Screw
M-E (x4)
M5 Washer
M-F (x4)
Spacer
T-A (x1)
6mm Allen
Wrench
T-B (x1)
Wrench
17.6lbs
(8kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
TOOLS NEEDED
Phillips
Screwdriver
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

3
ASSEMBLY STEPS
Horizontal
Adjustments
Allows for greater
tilt adjustment
STEP 1
Attach one set of Prongs (B) to the top of Mount Base (A) using M4x8mm Screws (S-B) and a Phillips
head screwdriver. Ensure that VESA Head (A1) is pointing up as shown below.
Prongs can be installed in two dierent orientations
to allow for additional adjustment in the horizontal or
vertical direction, as noted in images.
Vertical
Adjustments
S-B
B
A1
A
S-B
A1
A
B
Allows for greater
side rotation adjustment

4
STEP 2
STEP 3
Attach Mounts Base (A) with Prongs (B) to the pegboard. Instal remaining set of Prongs (B) to
pegboard, slightly liing Mount Base (A) forward to get the Prongs behind the Base. Secure
Prongs (B) using M4x8mm Screws (S-B) and a Phillips head screwdriver.
Secure VESA Plate (C) to monitor using appropriate Screws (M-A thru M-D), Washers (M-E), and a
Phillips head screwdriver. Spacers (M-F) may be required.
S-B
B
A
C

5
STEP 4
Slide monitor with VESA Plate (C) onto the Mount Base (A). Secure VESA Plate (C) in place using
M6x10mm Thumbscrew (S-A).
C
S-A
A

6
Adjust as Desired
If monitor is sagging or adjustments need to be made, use 6mm Allen Wrench (T-A) to tighten or
loosen swivel joint on VESA Head (A1).
Adjust the positioning of monitor by loosen the four nuts on the Mount Base (A) using the
Wrench (T-B).
T-A
T-B
A
A1

7
[ THIS PAGE INTENTIONALLY LEFT BLANK ]

LAST UPDATED: 06/15/2023
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303