Vivo STAND-V101G1 User manual

Pneumatic Arm Single Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v101g1
SKU: STAND-V101G1
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Base
B(x1)
Lower Arm
C(x1)
Gas Spring Arm
M (x1)
4mm Allen
Wrench
N(x1)
6mm Allen
Wrench
L(x1)
3mm Allen
Wrench
J (x1)
Clamp
K (x4)
Flat Head
Bolt
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
M-A (x4)
M4x12
D(x1)
VESA Plate
E(x1)
Clamp Plate
F (x1)
Grommet
Plate
G(x1)
So Pad
H (x1)
Cover
I (x1)
Clamp Brace
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M-B (x4)
M5x12
M-C (x4)
D5 Washer

3
ASSEMBLY STEPS
STEP 1
OPTION A: Clamp Installation
Attach clamp brace (I) to base (A) using
flat head bolts (K) and tighten with
4mm Allen wrench (M). Apply so pad
(G) to underside of base. Loosen bolts
on back of clamp (J), leaving 6mm of
thread exposed.
For a desk thickness of 3/8” - 2-1/2” (10
- 58mm), hang assembled clamp into
top 4 slots of clamp brace, or for a desk
thickness of 2” - 3-3/8” (50 - 85mm),
into lower 4 slots. Place clamp plate (E)
on top of clamp bolts. Position base on
desktop and tighten clamp bolts evenly
using 6mm Allen wrench (N). Attach
cover (H) to back of clamp brace.
TOOLS NEEDED
33lbs
(14.97kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
A
I K
M
G
50-85mm
E
E
10-58mm
6mm
M
J
6mm
M
J
N
H

4
STEP 1 (Continued)
OPTION B: Grommet Base Installation
Attach grommet plate (F) to base (A)
using flat head bolts (K) and tighten with
4mm Allen wrench (P). Apply so pad
(G) to underside of base. Position base
over grommet hole in desktop, or drill a
3/8” (10mm) hole through the desk for
installation. Remove clamp bolt from
clamp (J) using 6mm Allen wrench (N)
if needed. Insert clamp bolt with clamp
plate (E) up through the underside of the
desk and tighten to the base using the
6mm Allen wrench.
STEP 2
STEP 3
Place lower arm (B) on top of base, and secure by turning the lower screw in back with 3mm Allen
wrench (L). Optionally, also tighten the upper screw to restrict swivel movement to +/-90 degrees.
Place gas spring arm (C) on top of lower arm, and secure by turning the screw in back with 3mm Allen
wrench (L).
F
K
M
G
J
NN
E

5
STEP 4
Install the VESA plate (D) to monitor using M4x12 bolts (M-A) or M5x12 bolts (M-B) with
washers (M-C), making sure the arrow in back is pointing up.
STEP 5
Pull back the release lever on the support bracket, then place the monitor with VESA plate
into the support.
STEP 6
If needed, adjust gas spring arm to support the monitor using the 6mm Allen wrench (N). Turn the
screw in back clockwise to decrease support, and counter-clockwise to increase. Adjust the tilt joint to
tighten or loosen tilt support.
TV
TV
TV
D
M-A
M-B
M-C
1
2
N
N

6
STEP 7
Remove cable cover on upper arm using a Phillips screwdriver. Slide cable cover on lower
arm forward to remove.
STEP 8
Organize cables, then reinstall cable covers to arms.

7
STEP 9
For safety, please do not extend the monitor behind the desk. This may cause instability and tip the
desk over.
Adjust as Desired
Please DO NOT rotate monitor past
rear edge of desk. Or else it will create
an unstable situation and may cause
equipment tipover.
PO
N
±90°/180°
+45°
-45°
±90°
±180°
±90°

LAST UPDATED: 03/06/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303