Vivo STAND-V101N User manual

Single Monitor Desk Mount with Extra Long Arm
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v101n
SKU: STAND-V101N
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
TOOLS NEEDED
17.6lbs
(7.98kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
A (x1)
Arm
B(x1)
Clamp
C(x1)
Pole
M-A (x4)
M4x12
M-B (x4)
M5x12
M-C (x4)
D5 Washer
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
D(x1)
Pole Cover
E(x1)
Grommet
Plate
F (x3)
Arm Cable
Clip
G(x1)
Support Plate
H (x1)
Cable Clip
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
NOTE: SOME HARDWARE MAY NOT BE USED
I(x5)
Rubber Pad
J(x3)
M6x16
K (x1)
4mm Allen
Wrench
L(x1)
5mm Allen
Wrench
M(x1)
6mm Allen
Wrench

3
ASSEMBLY STEPS
STEP 2
OPTION A: Clamp Installation (Desk
Thickness: 10mm - 88mm)
Mount the pole (C) to the clamp (B)
using M6x16 bolts (J). Tighten using
4mm Allen wrench (K). Apply the
rubber pads (I) to the underside of
the clamp, then attach the clamp to
the desktop.
OPTION B: Grommet Base
Installation (Desk Thickness: 10mm
- 75mm)
Separate the clamp (B) by removing
the bolts in back with the 4mm Allen
wrench (K). Remove the screw from
the top of the clamp bolt (B), then
remove the clamp bolt. Remove the
screw from the top of the clamp bolt
(B), then remove the clamp bolt. Apply
the rubber pads (I) to the bottom
of the grommet base (E). Place the
support plate (G) onto the clamp bolt,
then insert the clamp bolt through the
grommet hole and grommet base, and
thread into the pole as shown in the
diagram.
STEP 1
Insert the pole cap (D) into the top of the pole (C).

4
STEP 3
Slide cable clip (H) and arm (A) onto the pole (C) and tighten using the 5mm Allen
wrench (L).
STEP 4
Attach the arm cable clips (F) to the arm (A) as shown.

5
STEP 5
Insert two bolts (M-A or M-B) and washers (M-C) into the top mounting holes
of the monitor, making sure to leave 3mm of thread exposed. Align bolts in
monitor over the slots in the VESA plate. Secure using two more bolts (M-A or
M-B) and washers (M-C) in the bottom two holes of the monitor. Tighten all
four bolts using a Phillips screwdriver.

6
STEP 6
Adjust the tilt support by turning the bolt on the side of the tilt joint using the 6mm Allen
wrench (M).
STEP 7
Store the 5mm and 6mm Allen wrenches (L, M) in the cable clip (H) for future
adjustments.

7
STEP 8
Use the cable clips (F, H) to organize cables.

LAST UPDATED: 01/26/2021
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303