Vivo STAND-V012L User manual

Dual Monitor Extra Tall Desk Mount
with Laptop Holder
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v012l
SKU: STAND-V012L
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
A (x1)
Pole Set
B(x1)
Clamp
C(x1)
Clamp Brace
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D1 (x1)
Swivel Arm
E(x3)
VESA Plate
F (x3)
M5x14
G (x2)
M8x12
H (x3)
Security Nut
I (x1)
M10 Washer
M (x1)
Allen Wrench
Set
J (x1)
Spring Washer
K (x1)
Grommet Base
Plate
L1 (x3)
Cable Clip
Q (x1)
Laptop Tray
N (x12)
M4x12
Thumbscrew
O (x12)
M4x30
P (x12)
M4 Spacer
R (x4)
M4x10 Bolt
S (x4)
M4 Nut
L2 (x6)
Cable Clip
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
T1 (x1)
Clamp Pad
T2 (x1)
Grommet Pad
D2 (x1)
Swivel Arm

3
ASSEMBLY STEPS
PRE-ASSEMBLY
STEP 1
TOOLS NEEDED
Phillips
Screwdriver Drill PER ARM
Option A: Desk Clamp Install
1. Install the clamp brace (C) to the pole (A) using x3 M5x14 bolts (F). See Figure 1.
2. Attach so pad (T1) to the clamp brace (C) , see Figure 2.
3. Install the clamp (B) to the pole assembly according to the thickness of the desktop. The
thickness can be changed to 3 positions. Connect using x2 M8x12 bolts (G) and tighten using the
Allen key (M). Tighten the clamp to the desktop using the plastic knob. See Figure 3.
a
Figure 1 Figure 2
T1
F
C
A
M
G
B
Wrench
22lbs
(9.98kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Thread the Pole Set (A) together as shown below.

4
STEP 1 (Continued)
STEP 2
Install Swivel Arms (D1, D2) to the Pole (A). Fasten the bolt
on each arm with the large Allen wrench (M). Attach the Wire
Clips (L1, L2) to the pole (A) and Swivel Arms (D).
Option B: Grommet Install
1. If desk does not have an existing grommet
hole, drill a 3/8” (10mm) diameter hole at the
desired position through the mounting surface.
2. Completely disassemble clamp (B) into
individual parts. Set knob (B1) and clamp
plate (B2) aside for later use. The L bracket,
bolt, washer and bushing will not be used.
3. Install grommet base plate (K) to the pole (A)
using x3 M5x14 bolts (F). See Figure 4.
4. Attach so pad (T2) to the grommet base plate
(K), see Figure 5.
5. Position pole (A) on the mounting surface
and secure using the clamp plate (B2), spring
washer (J), M10 washer (I) and knob (B1). See
Figure 6.
B1
B2
B2
B1
a
m
f
Figure 4
t2 Figure 5
a
m
f
Figure 4
t2 Figure 5
A
K
J
I
T2
F
D1
A
D2
L2
L1
M

5
STEP 3
FOR LAPTOP
Attach VESA plate (E) to laptop tray (Q) using
bolts (R) and M4 nuts (S).t
u
v
FOR FLAT BACK MONITOR
Attach VESA plate (E) to the monitor using
M4x12 thumb screws (N).
NOTE: Hand tighten screws to avoid over
tightening. q
R
Q
S
N
FOR CURVED BACK MONITOR
Attach VESA plate (E) to the monitor using bolts
(O) and spacers (P).
NOTE: Gently tighten with a screwdriver.
s
r
P
O
E
E
E

6
STEP 4
Slide the monitor onto the head of Swivel Arm (D) as shown in the diagram. Install the security
Nut (H). Make sure the security nut is installed before you rotate the monitor. Repeat for the
laptop tray (Q).
h
H

7
STEP 5
STEP 6
If needed, tighten the tilt joint bolt with the medium Allen wrench (M) to fix the tilt angle. Use the
medium Allen wrench (M) to adjust the swivel joints as needed.
Manage cables using the wire clips
(L1, L2). Store tools in the wire
clips (L1).
M
M
M
L2
L1
To level the monitors, remove the nut (H) and turn the bolt with the Allen key (M) to raise or lower the
monitor. Replace nut (H) aer the adjustment

LAST UPDATED: 09/17/2020
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303