Vivotek IP8152 User manual

IP Surveillance
Installation Guide
Using
AE-251/-252 Outdoor Enclosure,
AE-201/-202 Indoor Enclosure,
AM-114 Pendant Head (outdoor),
AM-116 and AM-117 Pendant Pipes,
AM-221 Gooseneck,
AM-212 Wall-mount bracket,
AM-311 Pole Mount,
AM-411 Corner Mount,
AM-711 Junction Box.
VIVOTEK IP8152 Mini Box Series
Outdoor Enclosure
Rev. 1.0
IP8152_housing_ig_VVTK_v1.0_20121206.indd 1 2013/1/10 下午 01:36:27

2
AE-251 and AE-252 Outdoor Enclosure Package Contents
Revison History:
Rev. 1.0: Initial release.
1. Enclosure.
2. Dome cover.
3. Power supply with cable.
4. Camera Mount bracket.
5. Dome clearance
measurement tool.
6. Screws.
AE-201 and AE-202 Indoor Recess Mount Housing Package Contents
1. Enclosure (indoor).
2. Dome cover.
3. Trim ring.
4. Camera Mount bracket.
5. Dome clearance measurement tool.
6. Screws.
IP8152_housing_ig_VVTK_v1.0_20121206.indd 2 2013/1/10 下午 01:36:28

3
English
Compatible VIVOTEK Cameras
1
AE-201
AE-202
AE-251
AE-252
IP8152
Mechanical Dimensions
IP8152_housing_ig_VVTK_v1.0_20121206.indd 3 2013/1/10 下午 01:36:29

4
IP8152_housing_ig_VVTK_v1.0_20121206.indd 4 2013/1/10 下午 01:36:34

5
English
Compatible Accessories (2): AM-311 Pole Mount
Bracket
Compatible Accessories (3): AM-411 Corner Mount Bracket
Compatible Accessories
2
Warning:
1. Select a suitable location where the camera is free from accidental damage, tampering,
or harsh environmental conditions.
2. Locate a place for the installation where the camera can not be intentionally or
unintentionally interfered.
3. Select a solid and at mounting surface that can support the combined weight of the
camera and associated hardware. Vibration and temperature ranage should also be
taken into consideration.
Compatible Accessories (1-1): AM-221 Gooseneck Bracket
Compatible Accessories (1-2): AM-212
Wall-mount Bracket
IP8152_housing_ig_VVTK_v1.0_20121206.indd 5 2013/1/10 下午 01:36:36

6
Compatible Accessories (4): AM-711 Junction Box
Compatible Accessories (5-2): AM-116 and AM-117 Pendant Pipe
Compatible Accessories (5-1): AM-114 Pendant Head
IP8152_housing_ig_VVTK_v1.0_20121206.indd 6 2013/1/10 下午 01:36:37

7
English
Mounting & Cabling with Outdoor Enclosures
3
3-1. Installing Camera to AE-251 and AE-252 Housing
Below is a general sample procedure using an outdoor enclosure:
1. Use a Phillips screwdriver to loosen the 2 screws on the sides of the camera bracket.
2. Detach the inner bracket by loosening the
four thumb screws on the sides.
IP8152_housing_ig_VVTK_v1.0_20121206.indd 7 2013/1/10 下午 01:36:38

8
3. The IP8152 supports 4 different lens modules. If you are installing the larger lens [AL-
231(2.8-12mm), and AL-234(5-50mm)], you need to remove the inner bracket and install
it in the opposite direction as shown below. Tighten the hand screws from the sides.
4. Reverse the inner bracket if the larger lens (AL-231 and AL-234) are used. Secure the
inner bracket from the sides as illustrated below.
-- 1
-- 3
-- 5
-- 7
-- 9
-- 11
-- 13
-- 15
2 --
4 --
6 --
8 --
10 --
12 --
14 --
16 --
-- 1
-- 3
-- 5
-- 7
-- 9
-- 11
-- 13
-- 15
2 --
4 --
6 --
8 --
10 --
12 --
14 --
16 --
Smaller lens:
Mounted on the
outer edge of
bracket
Larger lens:
Mounted inside the bracket
IP8152_housing_ig_VVTK_v1.0_20121206.indd 8 2013/1/10 下午 01:36:41

9
English
5. Secure camera to the bracket assembly by driving a athead screw.
6. Bend the included measurement
tool into a rectangular arch.
Attach the measurement tool
to the top of camera lens to
ensure your lens will not get in
the way when the dome cover
is installed.
The vertical length of the
measurement tool equals the
clearance between the bracket
and the dome cover.
IP8152_housing_ig_VVTK_v1.0_20121206.indd 9 2013/1/10 下午 01:36:42

10
.
You should also swing the measurement tool and the camera back and forth to make
sure there is enough clearance at different shooting angles. You can make adjustments
by changing the camera's position along the bracket.
7. Secure the camera to the large base bracket by fastening
the 4 thumb screws while you orient your camera's
shooting direction.
IP8152_housing_ig_VVTK_v1.0_20121206.indd 10 2013/1/10 下午 01:36:43

11
English
Make adjustments to the camera's shooting direction.
8. Feed power lines and other cables through a gooseneck bracket, a pendant head, or a
pendant pipe.
IP8152_housing_ig_VVTK_v1.0_20121206.indd 11 2013/1/10 下午 01:36:44

12
10. Install the camera into the housing by driving 2 M6 screws.
11. Depending on your choice with the mounting type using a gooseneck
or other accessories, refer to the instructions in the following sections to
complete the installation. The dome cover is installed after you complete
9. Insert and connect power cables and the Ethernet cable as shown below. The IP8152
can only be powered by a PoE Ethernet connection.
DC 12V input for onboard
heater
Unused
PoE
for
camera
hardware installation and acquire a
satisfactory imaging result.
IP8152_housing_ig_VVTK_v1.0_20121206.indd 12 2013/1/10 下午 01:36:45

13
English
3-2. Installing AE-201 and AE-202 Housing
Below is a general sample procedure using an outdoor enclosure:
1. Use a Phillips screwdriver to loosen the 2 screws on the sides of the camera bracket.
2. Detach the inner bracket by loosening the
four thumb screws on the sides.
IP8152_housing_ig_VVTK_v1.0_20121206.indd 13 2013/1/10 下午 01:36:47

14
Ø 290 mm hole
in diameter
3. For details about installing camera to the brackets, please refer to previous discussions
on page 7, page 9, page 10, page 11, and page 12; from step 3 to 7, step 10, and step
11.
4. Drill a hole on the ceiling that is 290mm in diameter.
6. Pull the stainless clamp on both sides of the housing out and into position.
5. Install the housing to the ceiling.
IP8152_housing_ig_VVTK_v1.0_20121206.indd 14 2013/1/10 下午 01:36:47

15
English
Clockwise: Brings the clamping plate closer
to ceiling
Counter-clockwise: Increases the clearance
7. Use a Phillips screwdriver to turn and to t the stainless clamping plates against the
ceiling board.
IP8152_housing_ig_VVTK_v1.0_20121206.indd 15 2013/1/10 下午 01:36:47

16
8. Install the trim ring to the housing by fastening 4 screws.
IP8152_housing_ig_VVTK_v1.0_20121206.indd 16 2013/1/10 下午 01:36:48

17
English
Below is a general, sample procedure using a gooseneck bracket:
1. Route power lines and other cables through the wall and the bracket.
2. Locate the position where you want to install the gooseneck bracket and camera. Drill
holes on the wall for securing the bracket and for routing the cables.
Secure the bracket by hammering anchors into the wall and then fasten hex nuts and
washers on them.
3. Attach the outdoor enclosure to the bracket by rotating it clockwise until it is tightly
fastened.
1
2
3
4
4. Use a hex wrench to secure the mounting adapter to the gooseneck bracket.
When cabling is done, proceed with initial setup such as enabling network access, focus
tuning, or zooming. When done, secure the outer dome cover.
Cables
AM-221
Gooseneck
bracket
IMPORTANT:
3-3. Gooseneck Installation
The screws and mounting surface must be able
to support a weight of 6 kg.
The same installation method applies to the
AM-212 wall-mount bracket.
IP8152_housing_ig_VVTK_v1.0_20121206.indd 17 2013/1/10 下午 01:36:48

18
Below is a sample procedure using a Pendant pipe:
1. Determine a hard surface ceiling location, and use the mounting holes on the pendant
head itself for marking where holes will be drilled to secure the pendant head. Drill
holes 10mm in diameter and 60mm deep.
3-4. Pendant Mount Installation
2. Locate the position where you want to install the pendant pipe and camera. Drill holes
on the ceiling for securing the pendant head. Secure the pendant head by hammering
anchors into the ceiling and then fasten screws through it.
IP8152_housing_ig_VVTK_v1.0_20121206.indd 18 2013/1/10 下午 01:36:48

19
English
3
4
5
7
6
Pendant Head
Pendant Pipe
Outdoor Enclosure
Cables
3. Route power lines and other cables through the side opening and a 1-inch conduit
(user-supplied), and through the pendant pipe.
4. Secure pendant pipe to the pendant head by rotating it clockwise until it is tightly
fastened.
IP8152_housing_ig_VVTK_v1.0_20121206.indd 19 2013/1/10 下午 01:36:49

20
7. Secure the connection using the included hex wrench.
When cabling is done, proceed with initial setup such as enabling network access, focus
tuning, or zooming. When done, secure the outer dome cover.
5. Secure the connection using the included hex wrench.
6. Attach the outdoor enclosure to the pendant pipe by rotating it clockwise until it is tightly
fastened.
IP8152_housing_ig_VVTK_v1.0_20121206.indd 20 2013/1/10 下午 01:36:49