Vivotek Insight IE9111-O User manual

User’s Manual
Qualcomm QCS605 SoC with Built-in AI Engine • Video Processing and Machine Learning •
Supports VCA Solutions via Installation of S&ST APPs •
Enables Any Type of Network Camera to act as AIoT Device
AI Box
IE9111-O
Driven by
OSSA
Rev. 1.0

VIVOTEK
2 - User's Manual
Table of Contents
Revision History ...............................................................................................................................................4
Read Before Use..............................................................................................................................................4
Symbols and Statements in this Document......................................................................................................4
Package Contents ............................................................................................................................................5
Physical Description ........................................................................................................................................6
Hardware Installation .......................................................................................................................................9
Conguration .................................................................................................................................................10
Remote Management.....................................................................................................................................15
Peripheral .......................................................................................................................................................15
Device Info .....................................................................................................................................................16
Privacy Mask ..................................................................................................................................................16
Virtual Camera ...............................................................................................................................................17
Stream Conguration .....................................................................................................................................17
Device Health .................................................................................................................................................18
User Management..........................................................................................................................................18
Network ..........................................................................................................................................................19
Date & Time....................................................................................................................................................19
Firmware ........................................................................................................................................................20
Applications - Overview..................................................................................................................................21
Data Magnet and VAST2................................................................................................................................21
Applications - Cloud Connection ....................................................................................................................25
Applications - Legal ........................................................................................................................................30
Technology License Notice.............................................................................................................................31
Electromagnetic Compatibility (EMC).............................................................................................................32

VIVOTEK
User's Manual - 3
Overview
• Powered by Qualcomm QCS605 SoC with a built-in AI Engine
• Powerful Computing for Video Processing and Machine Learning
• Designed with OSSA Technology Stack, running on S&ST Android OS
• Supports a variety of VCA solutions through S&ST APPs
• Enables Any Type of Network Camera to act as AIoT Device
• RJ-45 or M12 Connectors for PoE Connection
• Digital input*2, Digital Output *2
• EN50155 Compliance for Professional Mobile Surveillance

VIVOTEK
4 - User's Manual
Read Before Use
The use of surveillance devices may be prohibited by law in your country. The Network Camera
is not only a high-performance web-ready camera but can also be part of a exible surveillance
system. It is the user’s responsibility to ensure that the operation of such devices is legal before
installing this unit for its intended use.
It is important to first verify that all contents received are complete according to the Package
Contents listed below. Take note of the warnings in the Quick Installation Guide before the Network
Camera is installed; then carefully read and follow the instructions in the Installation chapter to
avoid damage due to faulty assembly and installation. This also ensures the product is used
properly as intended.
The Network Camera is a network device and its use should be straightforward for those who
have basic networking knowledge. It is designed for various applications including video sharing,
general security/surveillance, etc. The Configuration chapter suggests ways to best utilize the
Network Camera and ensure proper operations. For creative and professional developers, the URL
Commands of the Network Camera section serves as a helpful reference to customizing existing
homepages or integrating with the current web server.
Symbols and Statements in this Document
i
INFORMATION: provides important messages or advices that might help prevent
inconvenient or problem situations.
NOTE: Notices provide guidance or advices that are related to the functional integrity of
the machine.
Tips: Tips are useful information that helps enhance or facilitae an installation, function,
or process.
WARNING: or IMPORTANT:: These statements indicate situations that can be
dangerous or hazardous to the machine or you.
Electrical Hazard: This statement appears when high voltage electrical hazards might
occur to an operator.
Revision History
■ Rev. 1.0: Initial release.
NOTE:
1. The camera is only to be connected to PoE networks without routing to outside plants.
2. For PoE connection, use only UL listed I.T.E. with PoE output.

VIVOTEK
User's Manual - 5
Package Contents
■ IE9111-O
■ Screw pack.
■ Wall- / Panel-mount bracket.
■ Quick Installation Guide.
Any Type of Camera
Add New Features to
Existing Installation
S&ST Apps
Events & Metadata
Video Streaming for Recording
VAST2 (VMS)
Application

VIVOTEK
6 - User's Manual
Outer View
Physical Description
GbE LAN DI/DO
terminal Reset
PWR/Status
LEDs
Bracket Dimensions

VIVOTEK
User's Manual - 7
DI/DO Terminal Block Pinouts
DO1+ DO1- DO2+ DO2- DI1+ DI1- DI2+ DI2-
PWR
Status
LED Behavior
PWR Red ON Power is on
PWR Red ON + Status Green blinking System ready
PWR Red + Status Green blinking Reset taking place / restoring default
Consumption & Power Input
PoE: 802.3af class3
RX+
RX- TX+
TX-
M12 D-CODE 4 pin F
Below is the pinouts for the model that comes with a M12 connector:

VIVOTEK
8 - User's Manual
Hardware Reset
The reset button is used to reset the system or restore the factory default settings.
Sometimes resetting the system can return the camera to normal operation. If the system
problems remain after reset, restore the factory settings and install again.
Use a atten paper clip to press the button.
Reset: Press the recessed reset button. Wait for the Network Camera to reboot.
Restore: Press and hold the reset button until the status LED rapidly blinks. Note that all
settings will be restored to factory default. Upon successful restore, the status LED will
blink green and red during normal operation.

VIVOTEK
User's Manual - 9
Hardware Installation
1.The optional bracket allows you to install the AI box to a wall or panel. Secure the bracket
to the box using the included sunk head screws.
2.Secure the assembly to wall/panel using the included tapping screws and anchors.

VIVOTEK
10 - User's Manual
Conguration
1. Download the Device Management Tool. The tool can be requested here:
https://devices.securityandsafetythings.com/tooldownload
Make sure DHCP service is available in your local network.
2. Use the Device Management Tool to locate your device.

VIVOTEK
User's Manual - 11
3. You can click Cloud Login to download S&ST apps or visit:
https://store.securityandsafetythings.com/shop/catalog/c/main
4. Enter URL: https://<ip_address>:8443/
Enter admin/admin as the default credential.
Since the connection is using a self-signed certificate, your connection will not be
considered as a secure connection. Click Advanced to proceed.

VIVOTEK
12 - User's Manual
Click Proceed to xxx.xxx.xxx.xxx (Unsafe) to open the web console.
Note the IP addresses below are for reference only.
Enter admin/admin as the default credential.

VIVOTEK
User's Manual - 13
You will be requested to create a new password for security concern. Enter a
combination of alphabetic, numeric, and special characters that is strong enough for
protection.
The new password must comprise of at least 10 characters, containing uppercase,
lowercase, digits or special characters.

VIVOTEK
14 - User's Manual
IE9111-O
LAN
3rd-party camera
5. From the Remote device management page, you can enter the address, and credentials
for connecting to the 3rd-party IP camera.
Enter 8554 as the RTSP port.
Enter /live.sdp as the stream name. /live1s1.sdp can also be used.

VIVOTEK
User's Manual - 15
Remote Management
This page is used mainly to connect a 3rd-party network camera.
Peripheral
On this page you can see the current connection statuses of digital inputs. If your digitald
inputs are connected to sensor devices, its statuses will be automatically detected as being
pulled high or pulled low. You can also manually trigger a digital output. Digital outputs can
also be triggered via the Alarm settings.
These settings are dependent on camera make and model.

VIVOTEK
16 - User's Manual
Device Info
Important information about this device is displayed on this page: including Device ID, OS
version, AOSP API, SDK addon, rmware version, etc.
The Device ID is a unique ID for each camera and will be displayed in the Device
Management Portal.
Here, you can also reboot the device or perform a Factory reset.
Privacy Mask
Click and drag on the screen to block out sensitive areas in your eld of view. The size the
orientation will display on screen. Use the Intensity slide bar to determine how much image
within the privacy mask is blurred. Currently 1 privacy mask is supported.

VIVOTEK
User's Manual - 17
Stream Conguration
On this page, there are four pre-configured video streams which can be additionally
modied with regards to encoding, size, bitrate and I-frame interval.
Streams are dened as Full High Denition and Ultra High Denition streams.
Virtual Camera
Allows the creation of additional sub-stream(s) which can cover a certain zone of interest
in the camera's eld of view. The sub-streams are used for video analytics on apps.

VIVOTEK
18 - User's Manual
Device Health
This page displays various device health information: CPU/Memory/Storage usage,
Connectivity, Temperature and App status.
User Management
On this page, you can add/remove users and set user's rights and permissions.

VIVOTEK
User's Manual - 19
Network
By default, the AI box has the network setup to receive the IP address via DHCP. On this
page you can change different network parameters, disable the DHCP and set a specic
IP.
Date & Time
This page allows the user to congure the current date/time on the device, synchronize
with computer time and also to enable network time synchronization via an NTP server.
The network time setting is necessary when you "claim" the camera for downloading apps.

VIVOTEK
20 - User's Manual
Firmware
On this page you can perform a Firmware (OS version) OTA upgrade.