Vivotek FD7141 User manual

FD7141(V)

EN - 1
English
Power off the Network Camera as
soon as it is found smoking or smelt
unusual.
Contact your distributor when such cases
happen.
Refer to your user's manual for the
operating temperature.
Warning Before Install
Do not place the Network Camera on
unsteady surfaces.
Do not touch the Network Camera
when it's lightening.
Do not insert any object into the
Network Camera, such as needles.
Do not drop the Network Camera.

EN - 2
Software CD
FD7141 (FD7141V)
Quick installation guide /
Warranty card
Alignment sticker /
Ceiling hole template sticker
Alignment Sticker
Drill hole
At least drill 2 pilot holes
symmetrically on each
side to avoid falling.
Bottom base
Plastic cover (FD7141V only)
Power adapter
Package Contents
1
L-type hex key wrench /
Screws
Ceiling Hole Template Sticker
Drill hole

EN - 3
English
Tilt screw SD card
slot IR LEDs
Indented reset button
N.C.
485B
485A
AC24V
AC24V
Focus controller
Zoom controller
Image adjustment
screw
Status LED
Light sensor
Physical Description
2
Pan screw
Lens
Inner View
Ethernet 10/100 RJ45 plug
Audio out (green)
Microphone in (pink)
Power cord socket (black)
General I/O terminal
block
Earth
Fan
The fan will start working once
the temparature inside the
Network Camera is over 50°C.
f= 3.3~12 mm (FD7141 Lens)
f= 9~22 mm (FD7141V Lens)

EN - 4
Keep a note of the MAC address
under the camera base before
installing the camera. Network Camera
Model No: FD7141
Made in Taiwan
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Pat. 6,930,709
RoHS
V I
MAC:0002D1083236
Bottom base
Outer View
Dome cover
N.C.
485B
485A
AC24V
AC24V
Camera base
a
b
c
Hole a~c:
Holes for ceiling mount or for
attaching the bottom base.
a
b
c

EN - 5
English
First, use the supplied screwdriver to loose three screws and detach the dome cover from
the camera base. Then, follow the steps below to install the camera; either to a ceiling or to
a wall.
Hardware Installation
3
Ceiling mount with the bottom base
1. Attach the supplied Alignment Sticker to the ceiling.
2. Through the 10 circles on the sticker, drill 2 pilot holes symmetrically on each side into the ceiling.
Then hammer the supplied four plastic anchors into the holes.
3. Through four holes on the bottom base, insert the supplied four screws to corresponding holes and
secure the bottom base with a screwdriver.
4. Feed the cables through hole A or B. If you want to use hole B, remove the rubber with a screwdriver.
5. Secure the camera base to the bottom base with supplied three screws.
N.C.
485B
485A
AC24V
AC24V
1
2
3
45
A
B
Alignment Sticker
Drill hole
At least drill 2 pilot holes
symmetrically on each
side to avoid falling.

EN - 6
Wall mount with the bottom base
1. Attach the supplied Alignment Sticker to the wall.
2. Through the 10 circles on the sticker, drill 2 pilot holes symmetrically on each side into the wall. Then
Hammer the supplied four plastic anchors into the holes.
3. Through four holes on the bottom base, insert the supplied four screws to corresponding holes and
secure the bottom base with a screwdriver.
4. Feed the cables through hole A or B. If you want to use hole B, remove the rubber with a screwdriver.
5. Secure the camera base to the bottom base with supplied three screws.
1
2
3
5
A
B
4
Alignment Sticker
Drill hole
At least drill 2 pilot holes
symmetrically on each
side to avoid falling.

EN - 7
English
General Connection (without PoE)
N.C.
485B
485A
AC24V
AC24V
POWE
RC
OLLIS
ION
LINK
R
E
C
E
IVE
PAR
TITION
12345
Network Deployment
4
1. If you have external devices such as sensors and alarms, make
connections from general I/O terminal block.
2. Use the supplied RJ45 female/female coupler
to connect the Network Camera to a switch.
Use Catagory 5 Cross Cable when Network
Camera is directly connected to PC.
3. Connect the power cable from the Network
Camera to a power outlet.
N.C.
N.C.
N.C.
AC24V
AC24V
N.C.: NoConnector
N.C.: NoConnector
N.C.: NoConnector
AC24V: Power in AC 24V
AC24V: Power in AC 24V
GND: Ground
D I : Digital Input
D O : Digital Output
+12V : Power, 12V DC
GND
DI
DO
+12V
Ceiling mount without the bottom base (Embedded)
1. Attach the supplied Ceiling Hole Template Sticker to the wall.
2. Dig a hole along the inner circle of the sticker.
3. Through the 3 circles on the sticker, drill 3 pilot holes into the ceiling. Then hammer the supplied three
plastic anchors into the holes.
4. Mount the Netwrok Camera to the ceiling and feed the cables.
5. Through the three holes on the side of the camera base, insert the supplied three screws to corre-
sponding holes and secure them with a screwdriver.
1
5
23
4
Ceiling Hole Template Sticker
Drill hole

EN - 8
Power over Ethernet (PoE)
POWER COLLISION
LINK
RECEIV E
PARTITI ON
12345
N.C.
485B
485A
AC24V
AC24V
PoE switch
POWER COLLISION
LINK
RECEIV E
PARTITION
12345
N.C.
485B
485A
AC24V
AC24V
When using a non-PoE switch
Use a PoE power injector (optional) to connect between the Network Camera and a
non-PoE switch.
When using a PoE-enabled switch
The Network Camera is PoE-compliant, allowing transmission of power and data via
single Ethernet cable. See the following illustration to connect the Network Camera to a
PoE-enabled switch via Ethernet cable.
non-PoE switch
PoE power injector
(optional)

EN - 9
English
Network Camera
Model No: FD7141
Made in Taiwan
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Pat. 6,930,709
RoHS
V I
MAC:0002D1083236
1. Install the "Installation Wizard 2" under the Software Utility directory from software CD.
2. The program will conduct analyses on your network environment. After your network is
analyzed, please click on the "Next" button to continue the program.
3. The program will search the VIVOTEK Network Devices in the same LAN.
4. After searching, the main installer window will pop up. Click on the MAC that matches the
one labeled on the bottom of your device to connect the Internet Explorer to the Network
Camera.
0002D1083236
Installation
Wizard 2
Assigning IP Address
5