Vivotek FD8361 User manual

FD8361
P/N:625010100G Ver.1.0
Copyright 2009 VIVOTEK INC. All rights reserved.
c
2 MP H.264 Day&Night Vandal-proof

EN - 1
English
Power off the Network Camera as
soon as smoke or unusual odors are
detected.
Contact your distributor in the event of
occurrence.
Refer to your user's manual for the
operating temperature.
Warning Before Installation
Do not place the Network Camera on
unsteady surfaces.
Do not touch the Network Camera
during a lightning storm.
Do not insert sharp or tiny objects
into the Network Camera.
Do not drop the Network Camera.
625010100G_QIG, FD8361_20091221_V.1.0.indd 1 2009/12/21 PM 05:20:54

EN - 2
Software CD
FD8361
Quick Installation Guide /
Warranty Card
Alignment Sticker /
Ceiling Hole Template Sticker
Bottom Base
Power Adapter
5
1
0
0
0
0
2
1
0
G
Package Contents
1
L-type Hex Key Wrench / RJ45 Female/Female Coupler / Slica Gel / Screws
FD8361
P/N:625010100G Ver.1.0
Copyright 2009 VIVOTEK INC. All rights reserved.
c
2 MP H.264 Day&Night Vandal-proof
Ceiling Hole Template Sticker
Drill hole
625010100G_QIG, FD8361_20091221_V.1.0.indd 2 2009/12/21 PM 05:20:57

EN - 3
English
SD/SDHC Card Slot
IR LEDs (18 units,
distance 20m)
Reccessed Reset
Button
N.C.
N.C.
N.C.
AC24V
AC24V
Focus Controller
Zoom Controller
Status LED
Light Sensor
Physical Description
2
Pan Adjustment Screw
Inner View
Ethernet 10/100 RJ45 Plug
Audio Out (green)
Microphone In (pink)
Power Cord Socket (black)
General I/O Terminal Block
Ground
Fan
Operating environment: -20° ~ 50°C
When the temparature inside the Network
Camera reaches over 50°C, the fan will operate
automatically; when the temparature inside the
Network Camera drops to 0°C, the heater and fan
will both operate automatically.
BNC Video Output
Heater
Rotation Adjustment
Screw
Vari-focal Lens
(f= 3~9 mm)
Tilt Adjustment Screw
NTSC/PAL Video Output
Switch
625010100G_QIG, FD8361_20091221_V.1.0.indd 3 2009/12/21 PM 05:21:06

EN - 4
Record the MAC address under
the camera base before installing
the camera.
Network Camera
Model No: FD8361
Made in Taiwan
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Pat. 6,930,709
RoHS
V I
MAC:0002D1083236
CLASS A
IP66-rated Vandal-proof
Bottom Base
Outer View
IP66-rated Vandal-proof
Dome Cover
N.C.
N.C.
N.C.
AC24V
AC24V
Camera Base
a
b
c
Hole a~c:
Holes to secure the bottom base.
a
b
c
625010100G_QIG, FD8361_20091221_V.1.0.indd 4 2009/12/21 PM 05:21:08

EN - 5
English
First, use a screwdriver to loose the three screws and detach the dome cover from the
camera base. Then, follow the steps below to install the camera to either a ceiling or a wall.
Hardware Installation
3
Ceiling mount (with the bottom base)
1. Attach the supplied alignment sticker to the ceiling.
2. Using the 10 circles on the sticker, drill at least 2 pilot holes symmetrically on each side into the ceil-
ing. Then hammer the four supplied plastic anchors into the holes.
3. Through the four holes on the bottom base, insert the four supplied screws into the corresponding
holes and secure the bottom base with a screwdriver.
4. Feed the cables through hole A or B. If you want to use hole B, remove the rubber stopper with a
screwdriver.
5. Secure the camera base to the bottom base with three supplied screws.
N.C.
N.C.
N.C.
AC24V
AC24V
1
2
3
45
A
B
625010100G_QIG, FD8361_20091221_V.1.0.indd 5 2009/12/21 PM 05:21:16

EN - 6
Wall mount (with the bottom base)
1. Attach the supplied alignment sticker to the wall.
2. Using the 10 circles on the sticker, drill at least 2 pilot holes symmetrically on each side into the wall.
Then hammer the four supplied plastic anchors into the holes.
3. Using the four holes on the bottom base, insert the four supplied screws to corresponding holes and
secure the bottom base with a screwdriver.
4. Feed the cables through hole A or B. If you want to use hole B, remove the rubber stopper with a
screwdriver.
5. Secure the camera base to the bottom base with three supplied screws.
1
2
3
5
A
B
4
625010100G_QIG, FD8361_20091221_V.1.0.indd 6 2009/12/21 PM 05:21:24

EN - 7
English
General Connection (without PoE)
N.C.
N.C.
N.C.
AC24V
AC24V
POWER C
OLLIS
ION
LINK
RE
CEIVE
PARTITION
12345
Network Deployment
4
1. If you have external devices such as sensors and alarms, make the
connection from the general I/O terminal block.
2. Use the supplied RJ45 female/female coupler
to connect the Network Camera to a switch.
Use a Category 5 Cross Cable when Network
Camera is directly connected to PC.
3. Connect the power cable from the Network
Camera to a power outlet.
N.C.
N.C.
N.C.
AC24V
AC24V
N.C.: No Connector
N.C.: No Connector
N.C.: No Connector
AC24V: Power in AC 24V
AC24V: Power in AC 24V
GND: Ground
DI : Digital Input
DO : Digital Output
+12V : Power, 12V DC
GND
DI
DO
+12V
Drop-ceiling mount (without the bottom base)
1. Attach the supplied ceiling hole template sticker to the ceiling.
2. Open a hole along the inner circle of the sticker.
3. Using the 3 circles on the sticker, drill 3 pilot holes into the ceiling. Then hammer the three supplied
plastic anchors into the holes.
4. Mount the Network Camera to the ceiling and feed the cables through.
5. Using the three holes on the side of the camera base, insert the three supplied screws into the cor-
responding holes and secure them with a screwdriver.
1
5
23
4
Ceiling Hole Template Sticker
Drill hole
625010100G_QIG, FD8361_20091221_V.1.0.indd 7 2009/12/21 PM 05:21:29

EN - 8
Power over Ethernet (PoE)
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
N.C.
N.C.
N.C.
AC24V
AC24V
PoE Switch
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
N.C.
N.C.
N.C.
AC24V
AC24V
When using a non-PoE switch
Use a PoE power injector (optional) to connect between the Network Camera and a
non-PoE switch.
When using a PoE-enabled switch
The Network Camera is PoE-compliant, allowing transmission of power and data via a
single Ethernet cable. Follow the below illustration to connect the Network Camera to a
PoE-enabled switch via Ethernet cable.
Non-PoE Switch
PoE Power Injector
(optional)
625010100G_QIG, FD8361_20091221_V.1.0.indd 8 2009/12/21 PM 05:21:31

EN - 9
English
Network Camera
Model No: FD8361
Made in Taiwan
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Pat. 6,930,709
RoHS
V I
MAC:0002D1083236
CLASS A
1. Install “Installation Wizard 2” from the Software Utility directory on the software CD.
2. The program will conduct an analysis of your network environment. After your network is
analyzed, please click on the “Next” button to continue the program.
3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network
Cameras on the same LAN.
4. After searching, the main installer window will pop up. Click on the MAC that matches the
one labeled on the bottom of your device to connect to the Network Camera via Internet
Explorer.
0002D1083236
00-02-D1-08-32-36 192.168.5.109 FD8361
Installation
Wizard 2
Assigning an IP Address
5
625010100G_QIG, FD8361_20091221_V.1.0.indd 9 2009/12/21 PM 05:21:33