Vizualogic Advantage User manual

HEADREST MONITOR SYSTEM
99-9018-000 1/04
Installation Manual
1493 Bentley Drive • Corona, CA 92879 • 909-272-1996 • 800-624-7960 • Fax [phone]
www.vizualogic.com
Copyright © 2003 TMI Products, Inc.
All Rights Reserved
Corona, CA U.S.A.
060300
12 V Power Installation
We recommend the installation of a main power switch for the entire head-
rest system. The circuit should be marked to assist the consumer in locating
the correct vehicle fuse for the video system in the case of a system failure.
Vizualogic®Headrest System Diagram
- See diagram insert or go to www.vizualogic.com.
Winter 2004
Advantage™Series

Headrest Installation
Section I – Headrest Installation
1. Remove factory OE headrest.
2. Insert rigid wire “fishing tool” into the top of the headrest post guide and out the lower inside
corner of the seat back.
3. Hook end of headrest cable to the top of the “fishing tool” and pull cables through
the seat.
4. Insert the Vizualogic headrest with the IR channel A into the post guide tubes on the
driver side seat.
5. Insert the Vizualogic headrest with the IR channel B into the post guide tubes on the
passenger side seat.
6. Route headrest cable under the seat to the location of the A/V Controller. Be sure to secure your
wires and allow enough slack for seat travel on the tracks. Make sure the seat does not pinch or
cut cables.
Section II – Wiring
1. Place A/V module in a well protected area under seat or behind panel.
2. Connect 12 Volt harness to 12V + and 12V Ground. (use same power source
and ground as video sources). Wires are color-coded. Red = +12V Battery,
White = +12V accessory, Black = 12V Ground, Yellow = 12V Ground.
3. Use an A/V RCA cable to connect the DVD output to the input side of the A/V Controller box.
4. Connect monitor 1 and monitor 2 cables to the output side of the A/V Controller Box.
5. Select the headrest monitor that will be the master output to the FM Modulator. If you select
monitor 1 to be the master, connect the FM Modulator with “Y” cables (not
supplied) to slave 1 out. If you select monitor 2 connect to slave 2 out.
6. Pull radio and disconnect the antenna wire from the radio. Now connect the car radio antenna
cable to the FM Modulator. Connect the male FM Modulator cable to the back of the radio.
(Refer to the FM Modulator owner’s manual). Connect power to the FM Modulator. (Note –
Antenna adapter may be required for some GM vehicles)
7. Set the A/B switch on the head phones to match the A or B channel selected on the head rest.
The IR transmitter for the wireless head phones is built into the screens. To switch the A/B IR
setting you must push and hold the menu button. This will allow you to access the sub menu.
The Driver Seat should be set on channel A, and the passenger side should be set on channel B.
Section III – IR Repeater (included in the A/V Control Module).
An IR repeater is built into each monitor allowing video source control by pointing the remote at he
screen. This feature eliminates the need to install a stand-alone IR repeater elsewhere in the vehicle.
Use supplied black wire with 1/8˝ phono jacks to connect source and A/V Controller Box. IR 1 and
IR 2 inputs are located on the A/V Control Module.
Kits
VizuaLogic®offers 3 different ways to buy PerfectMatch™
Headrest Monitor Systems:
1. Vehicle Specific Kit (2 headrest monitors)
2. Single Headrest Monitor Kit (1 headrest monitor)
3. Dual Headrest Monitor Kit (2 headrest monitors)
Each Vehicle Specific Kit includes:
• 2 VizuaLogic PerfectMatch™OEM Headrest Monitors
• A/V control module with dual source
video inputs
• Unified remote control. Controls monitor
functions, A/V source input selection
and Vizualogic DVD.
• 2 Wireless two-channel crystal tuned
IR head phones
• 1 FM modulator
• Some wiring components may not be included.
Each Monitor Kit includes:
• 1 or 2 VizuaLogic PerfectMatch™OEM
Headrest Monitors
• A/V control module with dual source
video inputs
• Unified remote control. Controls monitor functions,
A/V source input selection and Vizualogic DVD.
Advantage™Series Advantage™Series