Vogelzang International VG650ELG User manual

852131

Pa
g
e 2
|
VG650ELG MOUNTAINEER™ www.vogelzang.com VGZ-025
|
20120424.1
SAFETY INSTRUCTIONS – Read All Instructions carefully.
1. The installation of this stove must comply with
your local building code rulings. Please observe
the clearances to combustibles (see reference
figures 7– 9). Do not place furniture or other
objects within the clearance area.
2.
Verify that the stove is properly assembled and in-
stalled before firing the stove for the first time. After
reading these instructions, if you have any doubt
about your ability to complete your installation
properly, you must obtain the services of a
professional licensed installer familiar with all
aspects of safe and correct installation. DO NOT
USETEMPORARY OR MAKESHIFT COMPRO-
MISES during installation. There must be NO
DEVIATION OR ALTERATION OF ANY KIND
from the very specific instructions spelled out in
this instruction manual as it pertains to the instal-
lation of this woodstove. NO EXCEPTIONS!
3. DO NOT store wood, flammable liquids or other
combustible materials too close to the unit. Refer
to certification label on back of unit and reference
figures 7 – 9 in this manual.
4. DO NOT INSTALL THIS STOVE IN A MOBILE
HOME, MANUFACTURED HOME, TRAILER
OR TENT – NO EXCEPTIONS! (HUD Federal
Standard: 24 CFR Ch.XX).
5.
DO NOT ELEVATE THIS STOVE BY ANY
MEANS. (i.e. bricks under base, cement blocks)
Stove pedestal base must set directly upon
the solid-surface non-combustible floor as
specified in this stove instruction manual. DO
NOT MODIFY THIS STOVE IN ANY WAY!
Stove must be installed with pedestal base and
ash drawer provided, attached as shown in the
instructions. DO NOT OPERATE WITHOUT
ASH DRAWER OR ASH CLEAN OUT COVER
IN PLACE – NO EXCEPTIONS. Assemble only
with original parts as supplied and shown in this
manual. DO NOT OPERATE A STOVE THAT IS
MISSING ANY PARTS! If any parts are missing or
defective, please notify the dealer or manufacturer
immediately. Replace missing, broken or worn
parts with factory original or equivalent parts only.
6. CAUTION: DO NOT ALTER COMBUSTION AIR
CONTROL RANGE TO INCREASE FIRING OR
FOR ANY REASON. Altering or tampering with air
control beyond normal capacity will create unsafe
and hazardous conditions
.
7. Always connect this stove to a chimney and vent
to the outside. Never vent to another room or in-
side a building. DO NOT CONNECTTHIS UNIT
TO A CHIMNEY FLUE SERVING ANOTHER
APPLIANCE.
8. DO NOT CONNECT A WOOD BURNING
STOVE TO AN ALUMINUM TYPE B GAS
VENT. This is not safe. Use code-approved lined
masonry or a UL 103 HT Listed Residential Type
and Building Heating Appliance chimney. Use a
6” diameter chimney or larger, that is high enough
to give a good draft. (See specifics in installation
instructions).
9.
Be sure that your chimney is safely constructed and
in good repair. Have the chimney inspected by the fire
department or a qualified inspector. Your insurance
company should be able to recommend a qualified
inspector. Chimney connector pipe must be in good
condition. Replace if necessary before using stove.
10. Creosote or soot may build up in the chimney con-
nector and chimney and cause a house/building
fire. Inspect the chimney connector and chimney
twice monthly during the heating season and clean
if necessary. (See Service Hints, page 14)
11.
IN THE EVENT OF A CHIMNEY FIRE, turn the air
controls to closed positions, leave the building and
CALL THE FIRE DEPARTMENT IMMEDIATELY!
Have a clearly understood plan on how to handle a
chimney fire by contacting your local fire authority for
information on proper procedures in the event of a
chimney fire. After the fire is out, the chimney must
be cleaned and inspected for any stress or cracks
before starting another fire. Check the condition of
any combustibles surrounding the chimney.
12. To prevent injury, do not allow anyone to use this
stove who is unfamiliar with the correct operation
of the stove.
13. Do not allow ashes to accumulate above top of ash
drawer.
14. DISPOSAL OF ASHES Ashes should be placed
in a steel container with a tight fitting lid and moved
outdoors immediately. The closed container of
ashes should be placed on a noncombustible floor
or on the ground, well away from all combustible
materials, pending final disposal. If the ashes are
disposed of by burial in soil or otherwise locally
dispersed, they should be retained in the closed
container until all cinders have completely cooled.
Other waste shall not be placed in this container.
15. The special paints used on your stove may
give off some smoke and an odor while
they are curing during the first 12 to 15 fires. Addi-
tional smoke and odor may be emitted from the light
oils used in construction of the fire box.This should
disappear after a short period of time and not occur
again.Persons with lung conditions or owners of sus-
ceptible domestic pets (such as birds) should take
prudent precautions. Open windows and
doors as needed to clear smoke and/or odor.
Paint discoloration will occur if the stove is
over fired.
16.
This stove has a painted surface which is durable
but it will not stand rough handling or abuse. When
installing your stove, use care in handling.

VGZ-025 | 20120424.1 VG650ELG MOUNTAINEER™ | Page 3
17. DO NOT ELEVATE THE FIRE. Build fire directly on
the bottom of the firebox. This stove has not been
tested with the use of grates, andirons or other means
of elevating the fire and must not be used.
18. CLEAN STOVE FREQUENTLY as soot, creosote
and ash may accumulate. Clean exterior with soap
and warm water when stove is not hot. Do not use
any acids or scouring soap, as these solvents wear
and dull the finish.
19.
Do not operate stove while under the influence of
drugs or alcohol
20.
ALERT ALL PERSONS TO THE HAZARDS OF
HIGH SURFACE TEMPERATURES while stove is
in operation – especially young children. Keep away
from a hot stove to avoid burns or clothing ignition.
21. NEVER LEAVE SMALL CHILDREN UNSUPER-
VISED WHEN THEY ARE IN THE SAME ROOM
AS THE STOVE. If small children will be in the same
room as the stove during operation, provide a sturdy
barrier to keep them at a safe distance from the stove.
22. Keep stove area clear and free from all combustible
materials, gasoline, engine oil, naphtha and other
flammable vapors and liquids.
23. WHILETENDINGTHE FIRE ALWAYS WEAR PRO-
TECTIVE CLOTHING, fire retardant hearth gloves
and eye protection, to prevent burns.
24. NEVER OPERATE THIS STOVE WITHOUT ASH
DRAWER OR ASH CLEAN OUT IN PLACE OR
WITH THE DOOR OPEN except when re-fueling.
Such actions can result in very dangerous operating
conditions.
25. DO NOT OVER FIRE THE STOVE. Over firing will
occur if combustion air is uncontrolled as when oper-
sated without ash cleanout cover or ash drawer or if
feed door is left open during operation. Such actions
can result in very dangerous operating conditions.
While in operation, keep the feed door closed and
secured at all times except while tending the fire
26. DO NOT SMOTHER FIREWHEN ADDING FUEL. Do
not build fires against glass and do not load fuel to a
height or in such a manner that it creates a hazard
when opening the door.
27. NEVER LEAVE THE STOVE UNATTENDED with
door open. Always close the door after ignition.
28. DO NOT CONNECT TO OR USE IN CONJUNC-
TION WITH ANY AIR DISTRIBUTION DUCT WORK
UNLESS SPECIFICALLY APPROVED FOR SUCH
INSTALLATIONS.
29. A WOOD-BURNING STOVE MUST NEVER BE
INSTALLED IN A HALLWAY OR NEAR A STAIR-
CASE, as it may block egress in the event of a fire.
30. DO NOT INSTALL IN A SLEEPING ROOM.
31. DO NOT INSTALL IN AN ALCOVE OR INSIDE A
FIREPLACE.
SAFETY INSTRUCTIONS continued…
32. Install at least one smoke detector on each floor of
your home. Detectors should be located away from
the heating appliance to avoid false alarms.Detectors
should be located close to sleeping areas. Follow
the smoke detector manufacturer’s placement and
installation instructions. Maintain smoke detector per
manufacturer’s instructions.
33. CARBON MONOXIDE (CO) HAZARD. A buildup of
CO fumes is toxic and can be fatal.Carbon Monoxide
is a colorless, odorless gas produced during combus-
tion of wood, coal, oil, gas and by other fuel burning
appliances. It is important to have a proper draft and
adequate replacement air ventilation so fumes are
drawn out the chimney. Installed as instructed this
stove is designed to be as safe as possible yet it is
recommended to install a CO detector. Follow the
manufacturer’s recommendations for proper instal-
lation and use. It is recommended to be placed at
table-top level (not near the ceiling) to avoid false
alarms. Realize that devices other than a stove (i.e.
motor exhaust) can trigger CO alarms.
If alarm sounds:
 s 2ECOGNIZETHESYMPTOMSOF#/POISONINGHEAD-
aches, nausea & drowsiness).
 s )NCREASEVENTILATIONOPENWINDOWSDOORS
 s -AKESURESTOVEDOORSANDORLIDSARECLOSEDAND
secured.
 s #HECKSTOVEFORSMOKINGORPUFlNGOPENAIRmOW
controls).
 s #HECKCHIMNEYCONNECTORPIPEFORLEAKSBLOCK-
age or down-draft conditions.
 s #HECK#/DEVICEFORFALSEALARM
34. The walls of the fire box may become slightly distorted
after a period of use. A slight distortion will not affect
34 operation of the stove.
35. Keep power cords, electrical appliances and/or as-
semblies outside of the clearance area shown in this
manual for combustible materials.
36. Consult your municipal building department or fire
officials about restrictions, permits and installation
requirements for your area.
37. For further information on using your stove
safely, a copy of the National Fire Protection
Association (NFPA) publication, “Using Coal and
Wood Stoves Safely” NFPA No. HS-10-1978. Write
NFPA, Batterymarch Park, Quincy, MA 02269.
NOTE: A PROFESSIONAL, LICENSED HEAT-
ING AND COOLING CONTRACTOR MUST
BE CONSULTED IF YOU HAVE QUESTIONS
REGARDING THE INSTALLATION OF THIS
SOLID FUEL BURNING APPLIANCE.
Vogelzang

Page 4 | VG650ELG MOUNTAINEER™ www.vogelzang.com VGZ-025 | 20120424.1
ASSEMBLY INSTRUCTIONS
NOTICE: Vogelzang grants no warranty, stated or implied, for the installation or maintenance of your wood stove and
assumes no responsibility of any incidental or consequential damages.
TOOLS
TOOLS AND MATERIALS REQUIRED FOR INSTALLATION
ŖPencil
Ŗ6 foot Folding Rule or Tape Measure
ŖTin Snips
ŖDrill: Hand or Electric
Ŗ1/8” dia. Drill Bit (for sheet metal screws)
ŖScrewdrivers (blade and Phillips type)
Ŗ14mm Nut Driver or Ratchet with 14mm Socket
ŖSafety Glasses
ŖGloves
MATERIALS
(NOTE: The following items are NOT included with your stove)
Chimney Connector Pipe: 6” dia. minimum 24 MSG black or 26
MSG blue steel stove pipe or elbow(s) as required.
1/2” Sheet Metal Screws
Chimney: Existing 6” code-approved, lined masonry chimney
or 6” inside dia. Listed UL 103 HT manufactured chimney.
Furnace Cement (manufacturer recommends Rutland Code 78
or equivalent)
CAUTION: STOVE IS HEAVY. MAKE SURE YOU
HAVE ADEQUATE HELP AND USE PROPER
LIFTING TECHNIQUES WHENEVER MOVING
STOVE.
continued on next page
0RXQWLQJKROHV
RI)OXH&ROODU
7KHGDPSHUPXVWEH
LQVWDOOHGDVVKRZQLQ
WKLVLOOXVWUDWLRQ6OLGH
WKHGDPSHULQWRWKH
IOXHFROODURQDQ
DQJOHDQGWKHQVOLGH
WKHGDPSHUKDQGOH
WKUXWKHKROHVLQWKH
IOXHFROODU
FLUE COLLAR INSTALLATION
3HHORIIWKHWDSHEDFNLQJDQGDSSO\WRWKH
JURRYHRIWKHFROODU
0RXQWWKHFROODUWRWKHWRSRIWKHDSSOLDQFH
XVLQJWKHWKUHH[´%ROWV
ZDVKHUVDQGWKUHH:HOG7DEVSURYLGHGLQ
WKHSDUWVEDJ
5HPRYHWKHGDPSHUURGIURPWKHGDPSHU
WKHQUHLQVWDOODVVKRZQEHORZ

VGZ-025 | 20120424.1 VG650ELG MOUNTAINEER™ | Page 5
ASSEMBLY INSTRUCTIONS continued
V
ogelzang
.YTQ.ONTRAPNOITPIRCSEDYEK
1 Blower Housing Back 25089B 1
2 Blower Housing Front 25090B 1
124408rotoMrewolB3
4 Rheostat w/Nut and Knob 80090 1
190108gnihsuBfeileRniartS5
123208droCylppuSrewoP6
1
168198dleihStaeH7
8 10AB x 3/8 Hex Screw 83172 12
499732CwercSskeT4/3x21#S/N
ASSEMBLY INSTRUCTIONS
Step 1.
THE BLOWERASSEMBLY MUST BE DISCONNECTED FROM THE SOURCE OF ELECTRICAL
SUPPLY BEFORE ATTEMPTING THE INSTALLATION.
With pliers, cut the 6 micro-joints and remove panel. Note: Discard the panel.
Step 2.
Fix the assembly to the back of the stove with the four screws provided.
THE BLOWER ASSEMBLY IS INTENDED FOR USE ONLY WITH A STOVE THAT IS MARKED
TO INDICATE SUCH USE.
DO NOT ROUTE THE SUPPLY CORD NEAR OR ACROSS HOT SURFACES!
1
2
3
4
5
6
7
8

Page 6 | VG650ELG MOUNTAINEER™ www.vogelzang.com VGZ-025 | 20120424.1
LOCATING STOVE
1. The stove must be placed on solid concrete,
solid masonry, or when installed on a combus-
tible floor, on a listed UL 1618 Type 2 floor
protector, such as Hy-C or Imperial Model
UL4848BK or equivalent with 1.0 R-factor.
(NOTE: to calculate R-value of alternative
materials see page 20). The base must extend
at least 16˝beyond the front of the access door,
8˝to the sides, 8˝behind and must extend
under and 2 inches beyond either side of the
stove pipe if it is elbowed towards a wall. (See
figures 7 & 9 and consult local building codes
and fire protection ordinances.)
CAUTION: (FIRE HAZARD) CARPETING AND
OTHER COMBUSTIBLE MATERIAL MUST NOT
COVER THE FLOOR PROTECTOR. THESE
MATERIALS MUST REMAIN OUTSIDE OF
COMBUSTIBLE CLEARANCES, SEE FIG. 7– 9.
2. The stove must have its own flue. DO NOT
CONNECT THIS UNIT TO A CHIMNEY
FLUE SERVING OTHER APPLIANCES.
3. After observing the clearances to combus-
tible materials (figures 7–9), locate your floor
protector accordingly (figure 7) and care-
fully place the stove in your selected location.
Install connector pipe, elbows, and thimble as
required, utilizing either a recently cleaned and
inspected 6” masonry chimney or a 6” i.d. UL
103 HT listed chimney.
4. Use round 6” dia., minimum 24 MSG (mini-
mum standard gauge) black or 26 MSG blue
Fig. 7 – TOP VIEW Minimum Clearance Dimensions from Combustible Surfaces
P
P
P
5
P
Volgelzang
VG650
Use 48 x 48
Standard Size
Floor Protector
steel stove pipe. DO NOT use galvanized stove
pipe. Secure pipe/elbow sections with a mini-
mum of three (3) equally spaced sheet metal
screws at each joint and at the stove collar to
make the pipe rigid. DO NOT CONNECT
THIS STOVE TO ANY AIR DISTRIBU-
TION OR DUCT SYSTEM.
5. Recheck clearances from the stove, con-
nector stove pipe, and corner clearances
using the illustrations in figures 7–9 and
your local building codes or fire protection
ordinances.
NOTE: A WALL FACED WITH DRYWALL, BRICK
OR STONE MUST BE CONSIDERED A COMBUS-
TIBLE SURFACE.
6. DO NOT INSTALL THIS STOVE IN A MOBILE
HOME, MANUFACTURED HOME, TENT OR
TRAILER – NO EXCEPTIONS! (HUD Federal
Standard: 24 CFR Ch.XX)
7. The clearances provided are minimum
dimensions determined by US Test Standard UL
1488-1996, tested and applied by Intertek Test-
ing Services, the manufacturer’s testing labora-
tory. Installation of this stove must comply with
the latest edition of NFPA 211 for reduced clear-
ances and/or your local building code rulings.
Use whichever minimum dimensions are
LARGEST.
8. This stove meets U.S. Test Standard:
UL 1482-1996.
continued on next page

VGZ-025 | 20120424.1 VG650ELG MOUNTAINEER™ | Page 7
LOCATING STOVE continued…
Fig. 9a – Front View
Minimum Clearance Dimensions
from Combustible Surfaces
Fig. 9b – Side View
Minimum Clearance Dimensions
from Combustible Surfaces
CAUTION: KEEP FURNISHINGS AND OTHER
COMBUSTIBLE MATERIALS AWAY FROM THE
STOVE.
NOTE: BEFORE FIRING WOODSTOVE SLIDE
FIREBRICKS TOWARDS THE REAR SO NO
GAPS REMAIN BETWEEN BRICKS.
18-1/2"
18-1/2"
CORNER CLEARANCES
Fig. 8 – Top View
Minimum Corner Clearances
from Combustible Surfaces
V
ogelzang

Page 8 | VG650ELG MOUNTAINEER™ www.vogelzang.com VGZ-025 | 20120424.1
PIPE CONNECTOR INSTALLATION
1. The crimped end of the stovepipe fits inside
the stove flue collar. Install additional pipe and
elbow with the crimped end towards the stove.
This will allow any condensation in the flue to
run back into the firebox. Secure pipe/elbow
sections with three sheet metal screws at each
joint to make the piping rigid. Screws may be
no more than a maximum of 3˝/76mm apart.
NOTE: The first section of connector pipe must
be single-walled to properly attach to the flue
collar.
2. Horizontal pipe runs must slope upwards
towards the chimney at least 1/4” per foot of
horizontal run.
3. You must have at least 18 inches of clearance
between any horizontal piping and the ceil-
ing.
4. The pipe cannot extend into the chimney flue
(figure 10).
5. Secure pipe/elbow sections with a minimum of
three (3) equally spaced sheet metal screws at
each joint and at the stove collar to make the
pipe rigid.
6. It is recommended that no more than two (2)
90° bends be used in the stovepipe installa-
tion. The use of more than two 90° bends may
decrease the amount of draw and possibly
cause smoke spillage. Where possible, use only
corrugated (nonadjustable) elbows. These
provide a better seal.
7. The connector pipe must not pass through an
attic or roof space, closet, or any concealed
space, or floor, ceiling, wall or combustible
construction. (See Chimney Connector Sys-
tems & Clearances, page 12). A UL 103 HT
listed chimney system must be used from
the first penetration of ceiling or wall to the
chimney cap. Any ceiling or wall penetrations
must conform to NFPA 211. Use only one
manufacturer’s chimney components – do not
mix manufacturers.
WARNING: DO NOT USE SINGLE WALL CON-
NECTOR PIPE AS A CHIMNEY - A HOUSE FIRE
COULD RESULT.
Fig. 10 – Stovepipe/Flue Connections
CORRECT WRONG WRONG
NOTE: STOVE PIPE IS NOT INCLUDED. TO
PURCHASE,VISITYOUR LOCAL HARDWARE,
HOME OR BUILDING CENTER. USE ROUND
v$)!-).)-5--3'minimum standard
gauge) BLACK OR 26 MSG BLUE STEEL
STOVE PIPE. DO NOT USE GALVANIZED
STOVE PIPE.

VGZ-025 | 20120424.1 VG650ELG MOUNTAINEER™ | Page 9
CHIMNEY
FLUE
5/8" TILE
CHIMNEY
LINER
MASONRY
CHIMNEY
THIMBLE
COLLAR
6˝ROUND
24 ga. BLACK
STOVEPIPE
8˝MIN.
LINER
BELOW
ENTRY
HOLE
MASONRY CHIMNEY
Chimney must be a code-approved, ma-
sonry chimney with flue liner. Before using an
existing masonry chimney, clean the chimney,
inspect the flue liner and make any repairs
needed to be sure it is safe to use. Make re-
pairs before attaching the stove. The connector
stove pipe and fittings you will need to connect
directly to a masonry chimney are shown in
figure 11.
CHIMNEY CONNECTIONS
The stove must be connected to either a ma-
sonry or manufactured metal chimney built and
tested to the specifications listed on the previous
pages.
Chimneys perform two functions:
1). As a means of exhausting smoke and flue
gases which are the result of fuel combustion.
2). The chimney provides “draft” which allows
oxygen to be continuously introduced into the
appliance, so that proper combustion is possible.
This stove relies on natural draft to operate.
NOTICE: Always provide a source of fresh air
into the room where the stove is located. Failure
to do so may result in air starvation of other fuel
burning appliances and the possible development
of hazardous conditions, fire or death.
Your stove itself does not create draft. Draft is
provided by the chimney. To achieve proper draft
your chimney must meet the three minimum height
requirements detailed in figures 12–14.A minimum
of 0.05 w.c. (measured in water column) is required
for proper drafting to prevent back puffing, smoke
spillage, and to maximize performance. (Gauges to
measure draft are readily available at stove stores
and are economical to rent or purchase.)
Factors such as wind, barometric pressure,
trees, terrain and chimney temperature can have
an adverse effect on the draft. The manufacturer
cannot be held responsible for external factors
leading to less than optimal drafting.
Should you have a problem with inadequate
draft, you should contact a licensed heating and
cooling contractor for assistance in solving the
problem.
IMPORTANT Installation Points
1. Size chimney flue to stove collar. This stove
requires a 6” diameter flue.
2. Never connect this unit to a chimney serv-
ing another appliance.
3. The chimney must meet all minimum
height requirements.
4. Never use a chimney to ventilate a cellar
or basement.
5. Contact your local building authority
for approved methods of installation and any
necessary permits and/or inspections.
Fig. 12 - Chimney Construction Through Attic Space
Fig. 11 - Masonry Chimney Connection
If the connector stove pipe must go through
a combustible wall before entering the masonry
chimney, consult a qualified mason or chimney
dealer. The installation must conform to local
building and fire codes and latest edition of NFPA
211.
If there is a cleanout opening in the base of the
chimney, close it tightly.
V
ogelzang

Page 10 | VG650ELG MOUNTAINEER™ www.vogelzang.com VGZ-025 | 20120424.1
Fig. 13 - Chimney Construction Through Roof
Fig. 14 - Chimney Connection to Firebox
Through Masonry Wall
CHIMNEY CONNECTIONS continued …
MANUFACTURED CHIMNEY
REFER TO CHIMNEY AND CHIMNEY CON-
NECTOR MAKER’S INSTRUCTIONS FOR INSTAL-
LATION AND USE.
Use only 6” diameter listed chimney UL 103 HT.
Chimney made to this listing is High Temperature rated
to 2100 degrees Fahrenheit. Use chimney from only one
manufacturer. Never mix brands. Carefully follow the
chimney manufacturer’s stated requirements and clear-
ances. Use the chimney manufacturer’s attic guards,
roof supports, flashing and fire stops when passing
through a ceiling. Use a listed thimble when passing
through a combustible wall. Do not use makeshift
compromises during installation.
WARNING: DO NOT USE A SINGLE-WALL
CONNECTION PIPE AS A CHIMNEY!
When using a pre-existing chimney, have it’s condi-
tion and installation inspected before using. Make sure
that the chimney meets all of the UL rating requirements
listed above. Be aware that not all manufactured chim-
ney is of the UL 103 HT type.
NOTE: It is recommended that you contact a li-
censed heating and cooling contractor (consult your
local yellow pages) for chimney installation.
Manufactured chimney with the proper required UL
listing is available from most home centers, hardware
stores, and HVAC supply stores.
If you have access to the internet, you may wish
to view chimney manufacturers’ information on-line.
See, www.duravent.com, www.selkirkinc.com, or
www.mtlfab.com.
VENTING TO EXISTING FIREPLACE
In some instances, people desire to convert an exist-
ing fireplace for stove use. Usually, safe connection to
an existing masonry chimney requires more work than
using a prefabricated chimney. The existing fireplace
must be closed and sealed at the damper with high-
temperature caulk, ceramic wool, or furnace cement.
Prior to installation, clean and inspect the existing flue
and smoke shelf. Installation should be designed so
the system can be dismantled for periodic cleaning and
inspection. Before conversion, make sure the existing
chimney is structurally sound, the chimney incorporates
a flue liner and make sure it is in good condition. (A flue
liner consists of clay tile that protects the brickwork of
a chimney. If a chimney does not have a liner, or it is
damaged, have it relined by a professional. DO NOT
continued on next page

VGZ-025 | 20120424.1 VG650ELG MOUNTAINEER™ | Page 11
CHIMNEY CONNECTIONS continued …
USE a chimney that is unlined or damaged!) If you
have any question regarding the condition of the chim-
ney, consult a qualified licensed contractor, qualified
engineer, competent mason, certified Chimney Sweep,
or a knowledgeable inspector. Consult your insurance
company if you cannot find a qualified expert.
CAUTION: NOT ALL FIREPLACE CHIM-
NEYS ARE SUITABLE FOR CONVERSION
TO ACCOMMODATE CONNECTION TO A
WOOD STOVE. CHECK WITH A QUALIFIED
EXPERT.
Many prefabricated fireplaces are of the “zero-
clearance fireplace” category. These consist of multi
layered metal construction. They are designed with
enough insulation and/or air cooling on the base, back
and sides so they can be safely installed in direct con-
tact with combustible floors and walls. Although many
prefabricated fireplaces carry endorsements from na-
tionally recognized organizations for use as fireplaces,
they have not been tested for connection to wood stove
heaters. Connecting a stove to such a device will void
the manufacturer’s warranty.
Venting a stove directly into a fireplace does not
meet code and should not be attempted. The stove war-
ranty will be void with such an installation. Do not cre-
ate a hazard in your home by connecting in this manner.
FIREPLACE INSTALLATION
FIG. 15 - Fireplace Conversion
should insure proper clearance for a 6˝stovepipe.
2. Install a fire clay (5/8˝minimum thickness) thimble.
Make sure the thimble is flush with the inner surface
of the chimney liner and does not protrude into the
flue (see figure 10 ).
3. Secure the thimble with refractory mortar. The
thimble should be surrounded by 12˝of solid unit
masonry brickwork or 24˝of stone.
4. Install the stovepipe into the thimble as far as pos-
sible without extending past the flue lining (see
figures 10 & 11).
5. A small airspace (about 1/2˝) should remain
between the stovepipe and thimble to allow for
expansion of the pipe. Seal this airspace with high-
temperature caulking or ceramic wool.
6. Secure and seal the damper in the closed position
using high-temp caulking, ceramic wool, or furnace
cement. Also check to see if the chimney has a clea-
nout. If it does, make sure it is closed and sealed
as well. A leaky cleanout will greatly reduce draft
efficiency.
If you have any questions regarding venting your
stove, contact the manufacturer or contact the Nation-
al Fire Protection Association (NFPA) and request a
copy of the latest editions of NFPA Standard 211 and
NFPA Standard 908. Their address is:
Battery March Park, Quincy, MA 02269.
Directly connecting the stovepipe into
the existing masonry chimney (figure 15
“Type A” Fireplace Conversion) of the fire-
place is the only approved method of instal-
lation. This is a complicated and involved
process and to insure safety should only by
done by a qualified installer.
1. An entry hole must be cut through the
masonry and tile liner with minimal
damage to the liner. At least 8” of liner
must remain below the entry position.
When locating the stove and stove-
pipe, all minimum clearances must be
observed from combustible surfaces
including mantels, combustible trim-
work, ceilings and walls. Positioning
the center of the stove pipe entry into
the chimney 24˝below the ceiling
Continued on next page
V
ogelzang

Page 12 | VG650ELG MOUNTAINEER™ www.vogelzang.com VGZ-025 | 20120424.1
A. Brick Masonry
Minimum 3.5˝/89mm thick brick masonry all framed into com-
bustible wall with a minimum of 12˝/305mm brick separation
from clay liner to combustibles. The fireclay liner shall run
from outer surface of brick wall to, but not beyond, the inner
surface of chimney flue liner and shall be firmly cemented in
place.
B. Insulated Sleeve
Solid-insulated, listed factory-built chimney length of
the same inside diameter as the chimney connector and
having 1˝/25.4cm or more of insulation with a minimum
9˝/229mm air space between the outer wall of the chimney
length and combustibles.
C. Ventilated Thimble
Sheet steel chimney connector, minimum 24 gauge in
thickness, with a ventilated thimble, minimum 24 gauge
in thickness, having two 1˝/25.4mm air channels, sepa-
rated from combustibles by a minimum of 6˝/152mm of glass
fiber insulation. Opening shall be covered, and thimble
supported with a sheet steel support, minimum 24 gauge in
thickness.
D. Chimney Section Pass-through
Solid insulated, listed factory-built chimney length with an
inside diameter 2˝/51mm larger than the chimney connec-
tor and having 1˝/25.4mm or more of insulation, serving as
a pass-through for a single wall sheet steel chimney con-
nector of minimum 24 gauge thickness, with a minimum
2˝/51mm air space between the outer wall of chimney
section and combustibles. Minimum length of chimney
section shall be 12˝/305mm chimney section spaced
1˝/25.4mm away from connector using sheet steel sup-
port plates on both ends of chimney section. Opening
shall be covered, and chimney section supported on both
sides with sheet steel support securely fastened to wall
surfaces of minimum 24 gauge thickness. Fasteners
used to secure chimney section shall not penetrate
chimney flue liner.
CHIMNEY CONNECTOR SYSTEMS & CLEARANCES

VGZ-025 | 20120424.1 VG650ELG MOUNTAINEER™ | Page 13
OPERATING INSTRUCTIONS
4HISSTOVEISDESIGNEDTOBURN
WOOD FUEL ONLY!
Hardwood, 16” to 18” should be air dried
(seasoned), for a minimum of 6 months to obtain
maximum burning efficiency. Logs greater than
6˝in diameter should be split. Wood should be
stored in a dry, well ventilated area. The humidity
content of usable firewood should be no more than
20% of the weight of the log.
Attempts to use wet or unseasoned wood will
cause,
sIGNITIONPROBLEMS
sRAPIDCREOSOTEBUILDUPRESULTINGINCHIMNEYlRE
sINCOMPLETECOMBUSTION
sLOWHEATYIELD
sBLACKENEDWINDOWS
NOTICE: USE SOLID WOOD MATERIALS ONLY.
DO NOT BURN GARBAGE OR FLAMMABLE
FLUIDS. DO NOT USE COALTHIS STOVE IS NOT
DESIGNEDTO ACCOMMODATETHE AIR FLOW
(DRAFT) NECESSARY TO PROPERLY BURN
COAL OR COAL PRODUCTS. DO NOT ELEVATE
FIRE OR USE GRATES OR ANDIRONS. BUILD
FIRE DIRECTLY ON BOTTOM OF FIREBOX.
LIGHTING
1. Open draft damper fully to provide maximum
draft.
2. Open the feed door and place several wads of
crushed paper in the firebox.
3. Lay small stacks of kindling on the paper to
start the fire.
4. Light the paper and kindling, close the door
and secure tightly.
5. Add fuel after fire is burning briskly. Use care
not to smother the kindling fire when adding
wood.
6. Close the door and secure tightly.
7. Adjust the draft damper control. The more
closed the slower the fire will burn. The more
open, the faster and hotter the fire will burn.
8. Do not over fire the stove.
ADDING FUEL
Add small amounts of fuel each hour or so
instead of piling large quantities of fuel at one
time. This will insure a more complete combustion
CAUTION: HOUSE FIRE HAZARDS
s $/./434/2%7//$/.&,//202/4%#-
TOR, UNDERNEATH STOVEPIPE OR ANY-
WHEREWITHIN MINIMUM CLEARANCES FROM
COMBUSTIBLE SURFACES SPECIFIED FOR
THIS STOVE.
s /6%2 &)2).' -!9 #!53% ! (/53% &)2%
YOU ARE OVER FIRING IF A UNIT OR CHIMNEY
CONNECTOR GLOWS RED.
OPERATING SAFETY PRECAUTIONS
1. NEVER OVER FIRETHIS STOVE BY BUILD-
ING EXCESSIVELY HOT FIRES AS A HOUSE/
BUILDING FIRE MAY RESULT. YOU ARE OVER
FIRING THE STOVE IF UNIT OR STOVEPIPE
BEGINS TO GLOW OR TURN RED.
2. NEVER BUILD EXTREMELY LARGE FIRES
IN THIS TYPE OF STOVE AS DAMAGE TO THE
STOVE OR SMOKE LEAKAGE MAY RESULT
3. ON MODELS WITH GLASS DOOR, DO NOT
BUILD FIRE TOO CLOSE TO GLASS.
4. UNIT IS HOT WHILE IN OPERATION. KEEP
CHILDREN, CLOTHING, AND FURNITURE AWAY.
CONTACT MAY CAUSE SKIN BURNS. DO NOT
TOUCH THE STOVE AFTER FIRING UNTIL IT
HAS COOLED.
5. PROVIDE AIR INTOTHE ROOM FOR PROP-
ER COMBUSTION.
6. INSPECT STOVEPIPE EVERY 60 DAYS.
REPLACE IMMEDIATELY IF STOVEPIPE IS
RUSTING OR LEAKING SMOKE INTO THE
ROOM.
continued on next page
WARNING: EXPLOSION HAZARD
s .%6%2 53% #(%-)#!,3 '!3/,).%
GASOLINE-TYPE LANTERN FUEL, KEROSENE,
CHARCOAL LIGHTER FLUID, OR SIMILAR
FLAMMABLE LIQUIDS TO START OR “FRESH-
%.50v!&)2%).4(%34/6%
s +%%0 !,, &,!--!",% ,)15)$3
ESPECIALLY GASOLINE, OUT OF THE
VICINITY OFTHE HEATER — WHETHER IN USE
OR IN STORAGE.
V
ogelzang

Page 14 | VG650ELG MOUNTAINEER™ www.vogelzang.com VGZ-025 | 20120424.1
process and less buildup of tars, soot, or creosote
will occur in the chimney.
1. Always open draft damper before opening the
feed door.
2. When adding fuel be careful not to smother the
fire. Do not build fires against glass on models
with glass door.
3. Close the feed door and secure tightly.
4. Adjust the draft damper control.
5. Empty ashes regularly. Do not allow ashes
to pile up (see Safety Instructions #14 on
page 2.)
6. Properly dispose of hot ashes (see Safety
Instructions, item #14 on page 2.)
7. Do not over fire the stove.
CAUTION: DO NOT OVER FIRE APPLIANCE.
YOU ARE OVER FIRING IF THE CHIMNEY
CONNECTORS OR STOVE GLOWS RED. CLOSE
THE DOOR AND SHUT FLUE DAMPER IMME-
DIATELY TO REDUCE THE AIR SUPPLY TO THE
FIRE. THIS WILL SLOW DOWN THE FIRE.
CAUTION: SLOW BURNING FIRES AND
EXTENDED USE MAY CAUSE EXCESSIVE
CREOSOTE BUILDUP. IGNITION OF CREO-
SOTE BUILDUP OR OVER FIRING MAY CAUSE
A CHIMNEY FIRE. CHIMNEY FIRES BURN
EXTREMELY HOT AND MAY IGNITE
SURROUNDING MATERIALS. IN CASE OF A
CHIMNEY FIRE CALL THE FIRE DEPARTMENT
IMMEDIATELY.
OPERATING continued …
CREOSOTE – FORMATION AND NEED
FOR REMOVAL
CAUTION: RISK OF FIRE WHEN WOOD IS
BURNED SLOWLY, IT PRODUCES TAR AND
OTHER ORGANIC VAPORS, WHICH COMBINE
WITH EXPELLED MOISTURE TO FORM CREO-
SOTE. THE CREOSOTE VAPORS CONDENSE
IN THE RELATIVELY COOL CHIMNEY FLUE
OF A SLOW-BURNING FIRE. AS A RESULT,
CREOSOTE RESIDUE ACCUMULATES ON THE
FLUE LINING.WHEN IGNITEDTHIS CREOSOTE
MAKES AN EXTREMELY HOT FIRE.
THE CHIMNEY CONNECTOR AND CHIMNEY
SHOULD BE INSPECTED AT LEAST ONCE
EVERY TWO MONTHS DURING THE HEATING
SEASON TO DETERMINE IF A CREOSOTE
BUILDUP HAS OCCURRED.
IF CREOSOTE HAS ACCUMULATED (3MM OR
MORE) IT SHOULD BE REMOVED TO REDUCE
THE RISK OF A CHIMNEY FIRE.
Failure to remove creosote may result in igni-
tion and may cause a house/building fire. Creosote
may be removed using a chimney brush or other
commonly available materials from your local
hardware retailer.
Chimney fires burn very hot. If the unit or
chimney connector should glow red, reduce the
fire by closing the inlet air control and immediately
call the fire department.
CAUTION: A CHIMNEY FIRE MAY CAUSE IGNI-
TION OF WALL STUDS OR RAFTERS WHICH
WERE ASSUMED TO BE A SAFE DISTANCE
FROM THE CHIMNEY. IF A CHIMNEY FIRE
HAS OCCURRED, HAVE YOUR CHIMNEY IN-
SPECTED BY A QUALIFIED EXPERT BEFORE
USING AGAIN.
A fire in the firebox may be smothered by pour-
ing a large quantity of coarse salt, baking soda, or
cool ashes on top of the fire.
PREVENTING CREOSOTE BUILDUP
1. Creosote will inevitably form in your chimney
and connector pipe. Following these steps will
help reduce the rate of build up.
2. BURN ONLY SEASONED WOOD that has
dried for at least one year. (<20% humidity by
weight)
3. Burn hardwood rather than softwood. Hard-
wood is denser or heavier wood and burns
hotter.
SERVICE HINTS

VGZ-025 | 20120424.1 VG650ELG MOUNTAINEER™ | Page 15
SERVICE HINTS continued …
4. Do not attempt to burn (or mix in) green or
wet wood. The use of green or wet wood will
cause a rapid build up of creosote. Wood that
hisses, sizzles and blackens without igniting
in five minutes must be considered too wet to
burn.
5. Do not attempt to extend the burn time by using
wet wood. Not only does burning wet wood
rapidly build up creosote, but it reduces the heat
output by up to 25 percent.
6. Burn the stove with the air inlet control wide
open for 10-25 minutes every time fresh wood
is loaded into the stove. Do not load more than
¼ to ½ of the fuel capacity at one time. Loading
too much wood at once will cause excessive
smoke which contains creosote. Mature fires
or coals produce very little creosote-producing
smoke.
7. Burn with the control open for several minutes
at numerous intervals throughout the day, be-
ing careful not to over fire the unit. Following
this process will help to warm the chimney
and reduce the amount of creosote forming
condensation within the chimney.
8. Establish a routine for the handling of fuel, fir-
ing, and operating the stove. Check daily for
creosote build up until experience shows how
often you need to clean for safe operation. Be
aware that the hotter the fire, the less creosote
is deposited and weekly cleanings may be nec-
essary in mild weather even though monthly
cleanings may be enough in the colder months.
WARNING: IN CASE OF CHIMNEY FIRE:
(1) CLOSE AIR INLET CONTROL(S)
(2) GET OUT OF THE HOUSE
(3) CALL THE FIRE DEPARTMENT.
CHIMNEY DRAFT
The chimney is critical to the proper operation
of the stove. It is the chimney that creates draft;
THE STOVE DOES NOTAND CANNOT CRE-
ATE DRAFT. The chimney provides two vital
functions for proper stove operation. First, it is
the passage to exhaust smoke and hot gases created
in the combustion process. Secondly, it supplies
the draft (or pressure) to bring oxygen to the fire
to sustain combustion. Draft is the natural move-
ment of air or gases through a chimney. Chimney
draft comes from the natural tendency for hot (less
dense) air to rise. As the hot air rises within the
chimney it creates a lower pressure at the bottom of
the chimney to which the stove is connected. The
higher pressure air outside the stove then rushes
into the stove where the lower air pressure level
exists, thus bringing oxygen to the fire. This con-
stant flow of air is referred to as the draft. Many
factors or combination of factors can act together
to build or impede the draft. Without the correct
amount of draft, the stove will not operate properly.
If there is excessive draft, an unsafe condition
will arise with too much air being drawn into the
stove and creating an excessively hot fire. This
could cause over firing which runs the risk of
igniting structural elements around the stove and
chimney.
The most common experience is that of insuf-
ficient draft. Under insufficient draft conditions,
the fire will be starved for oxygen, improper or
incomplete combustion occurs resulting in smoke
spillage into the area around the stove. A fire that
is starved for oxygen will not burn well. Such a
fire will produce excessive smoke that will cool
and condense in the chimney creating creosote.
Excessive amounts of creosote buildup can ignite
causing a chimney fire with the possibility of struc-
tural elements igniting as well.
Correct any draft related issues before using
the stove. The following are some possible causes
of insufficient draft. Please note that one or more
factors may play a role in a draft issue and certain
factors may change over time as conditions vary.
1. Atmospheric Pressure and Air Supply
Atmospheric pressure that affects the draft may
occur from outside the structure, inside the
structure, or both. High pressure weather (clear
and cold) usually produces a better chimney
draft than low pressure (overcast and damp)
conditions. Negative pressure can be created
inside a home by appliances that expel air from
within such as bathroom vents, range hoods,
clothes dryers, and forced air furnaces. Do not
allow such appliances to overcome the natural
draft. Note that newer homes tend to be built
more tightly allowing less make up air to seep
freely in. Negative pressure may be overcome
by opening a nearby door or window. In ex-
treme conditions of negative draft, the airflow
in the chimney will reverse direction. This is
known as “down drafting.”
V
ogelzang

Page 16 | VG650ELG MOUNTAINEER™ www.vogelzang.com VGZ-025 | 20120424.1
SERVICE HINTS continued
2. Environmental Factors
Wind or air deflecting off external objects such
as the roof, neighboring structures, trees, or
hills. These can cause a pressure change in the
air surrounding the chimney.
3. Chimney Temperature
The temperature of the chimney is an important
factor in how well it drafts. Warm chimneys
draft better than cold chimneys. This is based
upon the principle that hot air rises while cold
air sinks. Hot gases going up a cold chimney
will cool rapidly. Warm the chimney by allow-
ing a hot fire to burn for the first fifteen to thirty
minutes after starting the fire. Be careful not to
over fire the stove. If any part of the stove or
chimney starts to glow, you are over firing the
stove. Masonry chimneys will take longer to
warm than manufactured chimneys on account
of their greater structural mass. Chimneys
that have a flue diameter larger than the stove
outlet take more heat to warm, thus resulting
in a faster cooling of the hot gases needed to
build or maintain draft.
4. Chimney Installation and Maintenance
Confirm that all four minimum chimney
height requirements listed in the Chimney
Connection section of the manual have been
met. The physics that link chimney height with
draft creation are vital to the proper operation
of the stove. Failure to meet each of these
minimum requirements will have an adverse
affect on draft. Avoid long horizontal runs
or multiple elbows. Use stove cement to seal
joints in the connector pipe section. Regularly
clean the chimney, connector pipe, rain cap, and
spark arrestor screen. Creosote build up can
reduce the chimney draw and possibly create
a chimney fire.
5. Temporarily out of Operation
After the fire has burned out, open the air con-
trol to its fully open position. This will allow
warm room air to enter the chimney and keep
it as warm as possible until the stove is used
again.
For assistance involving chimney draft issues, con-
tact a knowledgeable licensed heating and cooling
contractor in your area. For questions regarding
manufactured chimney, contact the manufacturer
of the chimney.
NOTE: A DRAFT READING OF 0.05TO 0.06 W.C.
(WATER COLUMN) IS REQUIRED FOR PROPER
BURNING OF THIS STOVE.
GLASS CARE
CAUTION: DO NOT OPERATE WITH CRACKED
OR BROKEN GLASS.
Periodic cleaning of glass will be necessary to
prevent accumulations of ash. Acidic ash buildup
can eventually etch and weaken glass. Creosote
accumulations should burn off during hot fires. The
following usage and safety tips should be observed:
1. Inspect the glass regularly for cracks and
breaks. If you detect a crack or break, extin-
guish the fire immediately and contact the
manufacturer for a replacement before re-firing
the stove.
2. Do not slam the door or otherwise impact the
glass. When closing doors, make sure that logs
or other objects do not protrude to impact the
glass.
3. Do not build fires against (or that might fall
against) the glass.
4. Do not clean the glass with materials that
may scratch (or otherwise damage) the glass.
Scratches on the glass can develop into cracks
or breaks during operation.
5. Never attempt to clean the glass while the unit
is hot; allow to dry thoroughly before reuse.
If deposits are not very heavy, normal glass
cleaners are adequate using a soft, non-abrasive
cleaning pad.
6. Never put substances which can ignite explo-
sively in the unit. Even small explosions in
confined areas can blow out the glass.
GLASS REPLACEMENT
WARNING: REPLACE GLASS ONLY WITH 5MM
HIGH TEMPERATURE CERAMIC GLASS OF
THE PROPER SIZE. DO NOT USE SUBSTITUTE
MATERIALS SUCH AS TEMPERED GLASS
OR DOUBLE THICKNESS WINDOW GLASS!
CONTACT THE STOVE MANUFACTURER FOR
REPLACEMENT GLASS.
Gasket and Glass cleaning products are avail-
able at local retail home centers. Manufacturers
of cleaning products include, A.W. Perkins Co.
(www.awperkins.com) or Rutland Products (www.
rutland.com).
'LASS2EPLACEMENT0ROCEDURE
1. Ensure appliance is not in operation and is
thoroughly cooled.
2. Remove screw and glass clips. (See parts list
and diagram.)

VGZ-025 | 20120424.1 VG650ELG MOUNTAINEER™ | Page 17
SERVICE HINTS continued
WIRING DIAGRAM - VG650ELG MOUNTAINEER STOVE
3. Remove glass from door frame.
4. If glass is broken, carefully remove and discard
each broken piece to avoid cuts. Discard win-
dow gasket. Replace window and gasket with
original factory replacement parts.
5. Replace new gasket starting at the bottom of
glass working along edges, being sure to center
gasket channel on glass.
6. Trim to length and butt ends together.
7. Perform replacement procedure in reverse order
after replacing glass and gasket.
8. When replacing glass into door, be sure not to
overtighten screws and clips.
DOOR GASKET REPLACEMENT
CAUTION: DO NOT OPERATE A STOVE THAT
IS MISSING DOOR GASKET MATERIAL. OVER
FIRING AND UNSAFE OPERATING CONDI-
TIONS MAY RESULT.
After extensive use, the gasket material which
provides glass and door seal may lose it’s resiliency
and will need to be replaced. Inspect glass and door
gaskets periodically to ensure proper seal; if gas-
kets become frayed or worn, replace immediately.
Procedure:
1. Ensure appliance is not in operation and is
thoroughly cooled.
2. Remove old door gasket and clean channel.
3. Using an approved, high temperature gasket
cement, apply a thin coat in bottom of channel.
4. Starting at hinge side of door, work gasket into
channel around door unit, end butt and trim to
length.
5. Close door and allow three to four hours for
cement to set before firing appliance.
BLOWER MAINTENANCE
The optional blower is maintenance free other than
cleaning. Lightly vacuum motor and air inlet
to keep free of dust and dirt.
NOTICE: ANY REPLACE-
MENT WIRING MUST HAVE
EQUIVALENT INSULA-
TION AND TEMPERATURE
RATING (105°C).
NOTICE: DO NOT ALLOW
POWER CORD TO TOUCH
HOT SURFACES. KEEP
POWER CORD AT LEAST
v--&2/-34/6%/2
PIPE SURFACES.
CAUTION: MOVING PARTS CAN CAUSE
INJURY. DO NOT OPERATE WITH COVER
REMOVED.
DANGER:SHOCK HAZARD.DISCONNECT
POWER SOURCE BEFORE INSTALLATION
AND WHENEVER SERVICING BLOWER
ASSEMBLY.
V
ogelzang

OR ERIN ARTS EL MOUNTAINEER STO E
When ordering missing or replacement parts, always give the Model Number of the stove,
Part Number, and Part Description. Use the illustrations and part lists provided to identify parts.
Ref. No. Part No.Description Qty
1 69427B Ash Pan 1
2 40487 Ash Dump Cover - Square 1
N/S 40561 Ash Dump Cover - Round
3 24103 ½ Firebrick 2
4 89066 Full Firebrick 17
5 891110 Feed Door 1
N/S AC0600 Feed Door Gasket & Silicone 1
6 PL8535-01 Door Handle 1
7 891135 Spring Handle (Nickel) 1
8 AC09185 Door Barrell/Roller Ball/Pin Assy. 1
9 891108 Door Glass 1
N/S 88087 Door Glass Gasket 6Ft
10 891114 Top Window Bracket 4
Ref. No. Part No.Description Qty
11 PL02715 Bottom Window Bracket 1
12 83033 Machine Screw 8-32 x ¼ 12
13 891213 Hinge Pad 1
N/S 83274 Nut 3/8-16 2
N/S 83045A Washer 2
14 25298 Bae 1
15 891759 Hearth Trim - Nickel 1
16 83431 Weld Tab 3
17 25307 Flue Collar 1
18 88042 Gasket, Flue Collar 2 Ft
19 D6 Cast Iron Damper 1
N/S 891492 Blower Assembly 1
ORDERING PARTS - VG650ELG MOUNTAINEER STOVE

VGZ-025 | 20120424.1 VG650ELG MOUNTAINEER™ | Page 19
ORDERING PARTS - VG650ELG MOUNTAINEER STOVE
Glass replacement instructions for model VG650ELG
WARNING: REPLACE GLASS ONLY WITH 5MM
HIGH TEMPERATURE CERAMIC GLASS OF
THE PROPER SIZE. DO NOT USE SUBSTITUTE
MATERIALS SUCH AS TEMPERED GLASS
OR DOUBLE THICKNESS WINDOW GLASS!
CONTACT THE STOVE MANUFACTURER FOR
REPLACEMENT GLASS.
CAUTION: WHEN REMOVING BROKEN
GLASS, WEAR THICK GLOVES AND SAFETY
GLASSES. KEEP CHILDREN AWAY AND
DISCARD BROKEN GLASS SAFELY.
1. Be sure stove has cooled before beginning.
2. Using a screwdriver, remove all screws (#27)
and retainers (#11) holding glass.
3. Remove glass (#10). Replace with original
manufacture’s high-temperature ceramic glass
only.
4. When replacing broken glass, remove gasket
(#9) from broken glass and discard, remove all
glass pieces. Place new gasket material and trim
to butt ends together.
5. Reinstall glass, gasket and retainers.
WARNING: Do not use substitute materials.
Replace only with original manufacturer
components.
WARNING: Do not slam door or strike glass.
Slamming door or striking glass may cause
glass breakage.
WARNING: Do not use abrasive cleaners on
glass surface. Abrasives can damage the glass
and breakage may occur when heated.
CAUTION: Do not build fire directly against
glass.
CAUTION: Do not operate stove with
cracked or broken glass.
NOTICE: Periodically clean ash from glass
surfaces. Prolonged contact with acidic ash can
etch glass and weaken it.
When ordering missing or replacement parts, always give the Model Number of the stove, Part
Number, and Part Description. Use the illustrations and part lists provided to identify parts.
V
ogelzang

Page 20 | VG650ELG MOUNTAINEER™ www.vogelzang.com VGZ-025 | 20120424.1
FLOOR PROTECTOR MATERIAL CALCULATIONS
This stove has been tested for and must be installed on a floor protector with the proper Thermal
Resistance or R-value as stated in the installation instructions on page 6, “Locating Stove” step 1, of
this manual. If the floor protector materials listed in the instructions are not available, materials with
an equivalent R-value may be substituted.
Alternate materials may be rated with C-factor (Thermal Conductance) or k-factor (Thermal
Conductivity) ratings which must be converted to R-value to determine if the alternate material meets
the tested requirements. The following instructions provide the proper information and formulas for
conversion to R-value.
To determine if alternate materials are acceptable follow this sequence.
1. Convert material specifications to R-value:
a. R-value given — no conversion necessary
b. k-factor is given with a required thickness (T) in inches:
R = 1/k x T
c. C-factor is given: R = 1/C
2. Determine the R-value of proposed alternate floor protector:
a. Use formulas in step 1 above to calculate R-value of proposed material(s).
b. For multiple layers, add R-values of each layer to determine overall R-value.
3. If the overall R-value of the floor protector system is equal to or greater than the floor protector
specifications given, the alternate is acceptable.
Definitions:
Thermal conductance(C) = BTU =W
(hr)(ft2)(°F) (m2)(°K)
Thermal conductivity (k) = (Btu)(inch) =W=Btu
(hr)(ft2)(°F) (m)(°K) (hr)(ft)(°F)
Thermal resistance (R) = (ft2)(hr)(°F) =(m2)(°K)
Btu W
Example:
The specs of floor protector material should be 3/4-inch thick material with a k-factor of 0.84.
The proposed alternative material is 4” brick with a C-factor of 1.25 over 1/8-inch mineral board
with a k-factor of 0.29.
Step 1: Convert specs to R-value.
R = 1/k x T = 1/0.84 x 0.75 = 0.893 System must have a R-value of 0.893 = Rspecs
Step 2: Calculate R-value of individual components
4” Brick with C-factor = 1.25. R = 1/C = 1/1.25 = 0.80 = Rbrick
1/8-inch (0.125”) mineral board with k-factor = 0.29. R = 1/0.29 x 0.125 = 0.431 = Rmin.brd.
Step 3: Add R-values of components to get total R-value of system
Rbrick + Rmin.brd = 0.80 + 0.431 = 1.231 = Rsystem
Step 4: Compare Rsystem to Rspecs
Rsystem = 1.231 is larger than Rspecs of 0.893. System R-value exceeds the required
specifications and therefore is an acceptable alternative.