Vogelzang International VG450EL User manual

VGZ-014 / 20120424.0 Vogelzang International Corp. VG450EL FRONTIERSMAN™ / Page 1
Frontiersman™Woodstove
OWNERS MANUAL
Covers Models VG450EL, VG450ELG & VG450ELGB
(save this manual for future reference)
Vogelzang International Corporation
400 West 17th Street
Holland, Michigan 49423
www.vogelzang.com
Phone: [phone]
Fax: [phone]
This stove meets
U.S. Test Standard:
UL 1482-1996
READ ALL INSTRUCTIONS CAREFULLY
BEFORE INSTALLING OR OPERATING
THIS STOVE. FAILURE TO FOLLOW INSTRUC-
TIONS MAY RESULT IN PROPERTY DAMAGE,
BODILY INJURY, OR EVEN DEATH.
NOTE: IT IS RECOMMENDED INSTALLATION
BE COMPLETED BY A QUALIFIED HEATING
EQUIPMENT INSTALLER!
DO not INSTALL IN A MOBILE HOME.
REFER TO MARKINGS ON STOVE LABELS FOR
ADDITIONAL INFORMATION.
SAFETY NOTICE: IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE/BUILDING FIRE MAY
RESULT. FOR YOUR SAFETY, CONTACT LOCAL OR MUNICIPAL BUILDING OR FIRE OFFICIALS
ABOUT PERMITS, RESTRICTIONS, AND INSTALLATION REQUIREMENTS FOR YOUR AREA.

Page 2 / VG450EL FRONTIERSMAN™ www.vogelzang.com VGZ-014 / 20120424.0
1. The installation of this stove must comply with your
local building code rulings. Please observe the
clearances to combustibles (see reference figures
1– 3). Do not place furniture or other objects within
the clearance area.
2. Verify that the stove is properly assembled and
installed before firing the stove for the first time.
After reading these instructions, if you have any
doubt about your ability to complete your installation
properly, you must obtain the services of a
professional licensed installer familiar with all
aspects of safe and correct installation. DO NOT
USE TEMPORARY OR MAKESHIFT COMPRO-
MISES during installation. There must be NO
DEVIATION OR ALTERATION OF ANY KIND from
the very specific instructions spelled out in this in-
struction manual as it pertains to the installation of
this woodstove. NO EXCEPTIONS!
3. DO NOT store wood, flammable liquids or other
combustible materials too close to the unit. Refer
to certification label on back of unit and reference
figures 7 – 9 in this manual.
4. DO NOT INSTALL THIS STOVE IN A MOBILE
HOME, MANUFACTURED HOME, TRAILER OR
TENT – NO EXCEPTIONS! (HUD Federal Stan-
dard: 24 CFR Ch.XX).
5. DO NOT ELEVATE THIS STOVE BY ANY MEANS.
(i.e. bricks under legs, cement blocks) Stove legs
must set directly upon the solid-surface non-combus-
tible floor as specified in this stove instruction man-
ual. DO NOT MODIFY THIS STOVE IN ANY WAY!
Stove must be installed with legs provided, attached
as shown in the instructions. Assemble only with
original parts as supplied and shown in this manual.
DO NOT OPERATE A STOVE THAT IS MISSING
ANY PARTS! If any parts are missing or defective,
please notify the dealer or manufacturer immediately.
Replace missing, broken or worn parts with factory
original or equivalent parts only.
6. CAUTION: DO NOT ALTER COMBUSTION AIR
CONTROL RANGE TO INCREASE FIRING OR
FOR ANY REASON. Altering or tampering with air
control beyond normal capacity will create unsafe
and hazardous conditions .
7. Always connect this stove to a chimney and vent to
the outside. Never vent to another room or inside
a building. DO NOT CONNECT THIS UNIT TO A
CHIMNEY FLUE SERVING ANOTHER APPLI-
ANCE.
8. DO NOT CONNECT A WOOD BURNING STOVE
TO AN ALUMINUM TYPE B GAS VENT. This is
not safe. Use code-approved lined masonry or a UL
103 HT Listed Residential Type and Building Heat-
ing Appliance chimney. Use a 6” diameter chimney
or larger, that is high enough to give a good draft.
(See specifics in installation instructions).
9. Be sure that your chimney is safely constructed and
in good repair. Have the chimney inspected by the fire
department or a qualified inspector. Your insurance
company should be able to recommend a qualified
inspector. Chimney connector pipe must be in good
condition. Replace if necessary before using stove.
10. Creosote or soot may build up in the chimney con-
nector and chimney and cause a house/building
fire. Inspect the chimney connector and chimney
twice monthly during the heating season and clean
if necessary. (See Service Hints, page 14)
11. IN THE EVENT OF A CHIMNEY FIRE, turn the
damper control to closed position, leave the building
and CALL THE FIRE DEPARTMENT IMMEDIATE-
LY! Have a clearly understood plan on how to handle
a chimney fire by contacting your local fire authority
for information on proper procedures in the event of
a chimney fire. After the fire is out, the chimney must
be cleaned and inspected for any stress or cracks
before starting another fire. Check the condition of
any combustibles surrounding the chimney.
12. To prevent injury, do not allow anyone to use this
stove who is unfamiliar with the correct operation
of the stove.
13. Do not allow ashes to accumulate above top of ash
drawer.
14. DISPOSAL OF ASHES Ashes should be placed
in a steel container with a tight fitting lid and moved
outdoors immediately. The closed container of
ashes should be placed on a noncombustible floor
or on the ground, well away from all combustible
materials, pending final disposal. If the ashes are
disposed of by burial in soil or otherwise locally
dispersed, they should be retained in the closed
container until all cinders have completely cooled.
Other waste shall not be placed in this container.
15. The special paints used on your stove may
give off some smoke and an odor while
they are curing during the first 12 to 15 fires. Addi-
tional smoke and odor may be emitted from the light
oils used in construction of the fire box.This should
disappear after a short period of time and not occur
again.Persons with lung conditions or owners of sus-
ceptible domestic pets (such as birds) should take
prudent precautions. Open windows and
doors as needed to clear smoke and/or odor.
Paint discoloration will occur if the stove is
over fired.
16. This stove has a painted surface which is durable
but it will not stand rough handling or abuse. When
installing your stove, use care in handling.
17. DO NOT ELEVATE THE FIRE. Build fire directly on
the bottom of the firebox. This stove has not been
tested with the use of grates, andirons or other means
of elevating the fire and must not be used.
SAFETY INSTRUCTIONS

VGZ-014 / 20120424.0 Vogelzang International Corp. VG450EL FRONTIERSMAN™ / Page 3
18. CLEAN STOVE FREQUENTLY as soot, creosote
and ash may accumulate. Clean exterior with soap
and warm water when stove is not hot. Do not use
any acids or scouring soap, as these solvents wear
and dull the finish.
19. Do not operate stove while under the influence of
drugs or alcohol
20. ALERT ALL PERSONS TO THE HAZARDS OF
HIGH SURFACE TEMPERATURES while stove is
in operation – especially young children. Keep away
from a hot stove to avoid burns or clothing ignition.
21. NEVER LEAVE SMALL CHILDREN UNSUPER-
VISED WHEN THEY ARE IN THE SAME ROOM
AS THE STOVE. If small children will be in the same
room as the stove during operation, provide a sturdy
barrier to keep them at a safe distance from the stove.
22. Keep stove area clear and free from all combustible
materials, gasoline, engine oil, naphtha and other
flammable vapors and liquids.
23. WHILETENDINGTHE FIRE ALWAYS WEAR PRO-
TECTIVE CLOTHING, fire retardant hearth gloves
and eye protection, to prevent burns.
24. NEVER OPERATE THIS STOVE WITH THE DOOR
OPEN except when re-fueling. Such actions can
result in very dangerous operating conditions.
25. DO NOT OVER FIRE THE STOVE. Over firing will
occur if combustion air is uncontrolled as when oper-
ated with the feed door left open during operation.
Such actions can result in very dangerous operating
conditions. While in operation, keep the feed door
closed and secured at all times except while tending
the fire
26. DO NOT SMOTHER FIREWHEN ADDING FUEL. Do
not build fires against glass and do not load fuel to a
height or in such a manner that it creates a hazard
when opening the door.
27. NEVER LEAVE THE STOVE UNATTENDED with
door open. Always close the door after ignition.
28. DO NOT CONNECT TO OR USE IN CONJUNC-
TION WITH ANY AIR DISTRIBUTION DUCTWORK
UNLESS SPECIFICALLY APPROVED FOR SUCH
INSTALLATIONS.
29. A WOOD-BURNING STOVE MUST NEVER BE
INSTALLED IN A HALLWAY OR NEAR A STAIR-
CASE, as it may block egress in the event of a fire.
30. DO NOT INSTALL IN A SLEEPING ROOM.
31. DO NOT INSTALL IN AN ALCOVE OR INSIDE A
FIREPLACE.
32. Install at least one smoke detector on each floor of
your home. Detectors should be located away from
the heating appliance to avoid false alarms. Detectors
should be located close to sleeping areas. Follow
the smoke detector manufacturer’s placement and
installation instructions. Maintain smoke detector per
manufacturer’s instructions.
SAFETY INSTRUCTIONS continued…
33. CARBON MONOXIDE (CO) HAZARD.A buildup of
CO fumes is toxic and can be fatal. Carbon Monoxide
is a colorless, odorless gas produced during combus-
tion of wood, coal, oil, gas and by other fuel burning
appliances. It is important to have a proper draft and
adequate replacement air ventilation so fumes are
drawn out the chimney. Installed as instructed this
stove is designed to be as safe as possible yet it is
recommended to install a CO detector. Follow the
manufacturer’s recommendations for proper instal-
lation and use. It is recommended to be placed at
table-top level (not near the ceiling) to avoid false
alarms. Realize that devices other than a stove (i.e.
motor exhaust) can trigger CO alarms.
If alarm sounds:
 • RecognizethesymptomsofCOpoisoning(head-
aches, nausea & drowsiness).
 • Increaseventilation(openwindows&doors).
 • Makesurestovedoorsand/orlidsareclosedand
secured.
 • Checkstoveforsmokingorpufng(openairow
controls).
 • Checkchimney&connectorpipeforleaks,block-
age or down-draft conditions.
 • CheckCOdeviceforfalsealarm.
34. The walls of the fire box may become slightly dis-
torted after a period of use. A slight distortion will
not affect 34 operation of the stove.
35. Keep power cords, electrical appliances and/or as-
semblies outside of the clearance area shown in this
manual for combustible materials.
36. Consult your municipal building department or fire
officials about restrictions, permits and installation
requirements for your area.
37. For further information on using your stove
safely, a copy of the National Fire Protection
Association (NFPA) publication, “Using Coal and
Wood Stoves Safely” NFPA No. HS-10-1978. Write
NFPA, Batterymarch Park, Quincy, MA 02269.

Page 4 / VG450EL FRONTIERSMAN™ www.vogelzang.com VGZ-014 / 20120424.0
ASSEMBLY INSTRUCTIONS
tools
Safety Glasses & Gloves
Pencil
6 foot Folding Rule or Tape Measure
Tin Snips
Drill: Hand or Electric
1/8” dia. Drill Bit (sheet metal screws)
Screwdrivers (blade and Phillips type)
14mm Nut Driver or Ratchet with 14mm Socket
CAUTION: STOVE IS HEAVY. MAKE SURE YOU
HAVE ADEQUATE HELP AND USE PROPER
LIFTING TECHNIQUES WHENEVER MOVING
STOVE.
1. Uncrate the stove and remove cardboard
packing, styfofoam and protective poly bag.
Remove rear deflector (#21) from the carton.
(Save cardboard for further assembly.)
2. Remove parts from inside stove. Parts in-
clude: one damper collar (#1), four legs (#16),
hardware pack (#22) and air deflectors (#33)
located inside firebox.
3. Place flattened carton behind stove and care-
fully turn stove over onto its back on carton.
4. Remove the four 14mm nuts holding the
bottom floor shield in place.
5. Without removing the floorshield, place each
leg in position and secure using the four (4)
TOOLS AND MATERIALS REQUIRED FOR INSTALLATION
materials
(NOTE: The following items are NOT included with your stove)
Flooring Protection: 40” x 48” as specified (see page 4)
Chimney Connection: 6” dia. minimum 24 MSG black or 26 MSG
blue steel straig ht stove pipe or elbow(s) as required.
1/2” Sheet Metal Screws
Chimney: Existing 6” lined masonry chimney or 6” inside dia.
manufactured chimney system listed to UL 103 HT.
Furnace Cement (manufacturer recommends Rutland Code 78
or equivalent)
Continued on next page
14mm nuts removed in step 4. Tighten nuts
securely.
6. Carefully lift stove to upright position.
WARNING: METAL PANEL FASTENED BE-
TWEEN LEGS ACTS AS A HEAT DEFLECTOR.
THIS PANEL MUST BE IN PLACE FOR SAFE
OPERATION.
7. Attach rear deflector to the rear side corners of
the stove using four screws.
8. On VG450ELGB models (only), attach
blower assembly to rear of heat deflector.
NOTE: Make sure ceramic gasket is positioned
between rear deflector and blower assembly.
Attach two (2) air deflectors (#33) to the top
of the rear heat deflector. When installed, the
angled lip should face towards the front of the
stove.
9. Attach damper collar to rear top surface of stove
using machine screws.
LOCATING STOVE
1. The stove must be placed on solid concrete,
solid masonry, or when installed on a com-
bustible floor, on a listed UL1618 type 2 floor
protector, such as Hy-C or Imperial Model
UL 4048BK or equivalent with 0.8 R-factor.
(NOTE: to calculate R-value of alternative
materials see page 16). The base must extend
at least 16” beyond the side with the access
door, 8” to the sides of fuel opening, 8” behind
the stove, and must extend under the stove
pipe and 2” beyond each side if it is elbowed
towards a wall. (See figures 1 & 3 and consult
local building codes and fire protection ordi-
nances)
CAUTION: (FIRE HAZARD) CARPETING AND
OTHER COMBUSTIBLE MATERIAL MUST NOT
COVER THE FLOOR PROTECTOR. THESE
MATERIALS MUST REMAIN OUTSIDE OF
COMBUSTIBLE CLEARANCES, SEE FIG. 1– 3.
2. The stove must have its own flue. DO NOT
CONNECT THIS UNIT TO A CHIMNEY
FLUE SERVING OTHER APPLIANCES.
3. After observing the clearances to combus-
tible materials (figures 1–3), locate your floor
protector accordingly (figure 1) and care-
fully place the stove in your selected location.
Install connector pipe, elbows, and thimble as
NOTICE: Vogelzang International Corp. grants no warranty, stated or implied, for the installation or maintenance of
your wood stove and assumes no responsibility of any incidental or consequential damages.

VGZ-014 / 20120424.0 Vogelzang International Corp. VG450EL FRONTIERSMAN™ / Page 5
required, utilizing either a recently cleaned
and inspected 6˝ masonry chimney or a 6˝ i.d.
manufactured chimney listed to UL 103 HT.
4. Use round 6˝ dia., minimum 24 MSG (mini-
mum standard gauge) black or 26 MSG blue
steel stove pipe to connect the stove to the
chimney. Do not use galvanized duct pipe.
Secure pipe sections with three (3) sheet metal
screws in each stove pipe and/or elbow joint to
firmly hold the pipe sections together. Screws
may be no more than a maximum of 3˝/76mm
apart. DO NOT CONNECT THIS STOVE
TO ANY AIR DISTRIBUTION OR DUCT
SYSTEM.
5. Recheck clearances from the stove,
connector stove pipe, and corner clearances
using the illustrations in figures 1–3 and
your local building codes or fire protection
ordinances.
NOTE: A WALL FACED WITH DRYWALL,
BRICK OR STONE MUST BE CONSIDERED
A COMBUSTIBLE SURFACE.
LOCATING STOVE continued…
CAUTION: KEEP FURNISHINGS AND OTHER
COMBUSTIBLE MATERIALS AWAY FORM THE
STOVE.
NOTE: BEFORE FIRING WOODSTOVE SLIDE
FIREBRICKS TOWARDS THE REAR SO NO
GAPS REMAIN BETWEEN BRICKS.
Fig. 2 – TOP VIEW Minimum Corner
Clearances from Combustible Surfaces
Fig. 1 – TOP VIEW Minimum Clearance
Dimensions from Combustible Surfaces
FLOOR
PROTECTOR
DASHED LINE SHOWS HORIZONTAL CHIMNEY CONNECTOR
AND ADDITIONAL FLOOR PROTECTOR REQUIRED EXTENDING
BENEATH AND 2” BEYOND EACH SIDE.
COMBUSTIBLE CONSTRUCTION IN ACCORDANCE WITH NFPA 211
BACKWALL
SIDEWALL
8"min.
17"
48"
16"min.
8"min.24"
28"
min.
33"min
TOP VIEW
40"
6. DO NOT INSTALL THIS STOVE IN A MOBILE
HOME, MANUFACTURED HOME, TENT OR
TRAILER – NO EXCEPTIONS! (HUD FeDeral
StanDarD: 24 CFr CH.xx)
7. The clearances provided are minimum
dimensions determined by the manufacturer’s
testing laboratory shown on the front cover.
Installation of this stove must comply with the
latest edition of NFPA 211 for reduced clear-
ances and/or your local building code rulings.
Use whichever minimum dimensions are
LARGEST.
8. This stove meets U.S. Test Standard:
UL 1482-1996.
28"
28"
CORNER CLEARANCES

Page 6 / VG450EL FRONTIERSMAN™ www.vogelzang.com VGZ-014 / 20120424.0
Fig. 3a – FRONT VIEW
Minimum Clearance Dimensions
from Combustible Surfaces
Fig. 3b – SIDE VIEW
Minimum Clearance Dimensions
from Combustible Surfaces
CONNECTOR PIPE INSTALLATION
1. The straight end of the stovepipe fits over the
stove flue collar. Secure with three (3) sheet
metal screws.
2. Horizontal pipe runs must slope upwards
towards the chimney at least 1/4” per foot of
horizontal run. This allows any condensation
in the pipe to drain back into the firebox.
3. You must have at least 18 inches of clearance
between any horizontal piping and the ceiling.
4. The pipe cannot extend into the chimney flue
(figure 4).
5. Secure the pipe/flue collar and all pipe/elbow
sections with three (3) sheet metal screws at
each joint to make the piping rigid. Screws
may be no more than a maximum of 3˝/76mm
apart.
6. It is recommended that no more than two (2)
90° bends be used in the stovepipe installa-
tion. The use of more than two 90° bends may
decrease the amount of draw and possibly
cause smoke spillage. Where possible, use only
corrugated (nonadjustable) elbows. These
provide a better seal.
7. The connector pipe must not pass through an
attic or roof space, closet, or any concealed
space, or floor, ceiling, wall or combustible
construction. (See Chimney Connector Sys-
tems & Clearances, page 10). A manufactrured
chimney system listed to UL 103 HT MUST
be used from the first penetration of ceiling or
wall to the chimney cap. Any wall or ceiling
penetrations must conform to NFPA 211.
Fig. 4 – Stovepipe/Flue Connections
CORRECT WRONG WRONG
NOTE: STOVE PIPE IS NOT INCLUDED. TO
PURCHASE, VISIT YOUR LOCAL HARD-
WARE, HOME OR BUILDING CENTER. SEE
“LOCATING STOVE” PAGE 3 FOR ADDITIONAL
SPECIFICATIONS.
LOCATING STOVE continued…
WARNING: DO NOT USE SINGLE WALL CON-
NECTOR PIPE AS A CHIMNEY - A HOUSE FIRE
COULD RESULT.

VGZ-014 / 20120424.0 Vogelzang International Corp. VG450EL FRONTIERSMAN™ / Page 7
CHIMNEY
FLUE
5/8" TILE
CHIMNEY
LINER
MASONRY
CHIMNEY
THIMBLE
COLLAR
6˝ ROUND
24 ga. BLACK
CONNECTOR
STOVEPIPE
8˝ MIN.
LINER
BELOW
ENTRY
HOLE
Fig. 6 - Masonry Chimney Connection
CHIMNEY CONNECTIONS
The stove must be connected to either a mason-
ry or manufactured metal chimney built and tested
to the specifications listed on the previous pages.
Chimneys perform two functions:
1). As a means of exhausting smoke and flue
gases which are the result of fuel combustion.
2). The chimney provides “draft” which allows
oxygen to be continuously introduced into the
appliance, so that proper combustion is possible.
This stove relies on natural draft to operate.
NOTICE: Always provide a source of fresh air
into the room where the stove is located. Failure
to do so may result in air starvation of other fuel
burning appliances and the possible development
of hazardous conditions, fire or death.
Your stove itself does not create draft. Draft is
provided by the chimney. To achieve proper draft
your chimney must meet the three minimum height
requirements detailed in figures 7–9. A minimum
of 0.05 w.c. (measured in water column) is required
for proper drafting to prevent back puffing, smoke
spillage, and to maximize performance. (Gauges to
measure draft are readily available at stove stores
and are economical to rent or purchase.)
FACTORS SUCH AS WIND, BAROMET-
RIC PRESSURE, TREES, TERRAIN AND
CHIMNEY TEMPERATURE CAN HAVE AN
ADVERSE EFFECT ON THE DRAFT. The
manufacturer cannot be held responsible for ex-
ternal factors leading to less than optimal drafting.
Should you have a problem with inadequate
draft, you should contact a licensed heating and
cooling contractor for assistance in solving the
problem.
IMPORTANT Installation Points
1. Size chimney flue to stove collar. This stove
requires a 6” diameter flue.
2. Never connect this unit to a chimney serv-
ing another appliance.
3. The chimney must meet all minimum
height requirements.
4. Never use a chimney to ventilate a cellar
or basement.
5. Contact your local building authority
for approved methods of installation and any
necessary permits and/or inspections.
Fig. 7 - Chimney Construction Through Attic Space
MASONRY CHIMNEY
Chimney must be a code-approved, ma-
sonry chimney with flue liner. Before using an
existing masonry chimney, clean the chimney,
inspect the flue liner and make any repairs
needed to be sure it is safe to use. Make re-
pairs before attaching the stove. The connector
stove pipe and fittings you will need to connect
directly to a masonry chimney are shown in
figure 6.
If the connector stove pipe must go through a
combustible wall before entering the masonry chim-
ney, consult a qualified mason or chimney dealer.
The installation must conform to local building and
fire codes and latest edition of NFPA 211.
If there is a cleanout opening in the base of the
chimney, close it tightly.

Page 8 / VG450EL FRONTIERSMAN™ www.vogelzang.com VGZ-014 / 20120424.0
Fig. 8 - Chimney Construction Through Roof
Fig. 9 - Chimney Connection to Firebox
Through Masonry Wall
CHIMNEY CONNECTIONS continued …
MANUFACTURED CHIMNEY
REFER TO CHIMNEY AND CHIMNEY
CONNECTOR MAKER’S INSTRUCTIONS FOR
INSTALLATION AND USE.
Use only 6˝ diameter manufactured chimney
system listed to UL 103 HT. Chimney made to this
listing is High Temperature rated to 2100 degrees
Fahrenheit. Use chimney from only one manu-
facturer. Never mix brands. Carefully follow the
chimney manufacturer’s stated requirements and
clearances. Use the chimney manufacturer’s attic
guards, roof supports, flashing and fire stops when
passing through a ceiling. Use a listed thimble
when passing through a combustible wall. Do not
use makeshift compromises during installation.
WARNING: DO NOT USE A SINGLE-WALL CON-
NECTOR PIPE AS A CHIMNEY!
When using a pre-existing chimney, have it’s
condition and installation inspected before using.
Make sure that the chimney meets all of the UL rat-
ing requirements listed above. Be aware that not all
manufactured chimney is of the UL 103 HT type.
NOTE: It is recommended that you contact a
licensed heating and cooling contractor (consult
your local yellow pages) for chimney installation.
Manufactured chimney with the proper re-
quired UL listing is available from most home
centers, hardware stores, and HVAC supply stores.
If you have access to the internet, you may
wish to view chimney manufacturers’ informa-
tion on-line. See, www.duravent.com, www.
selkirkinc.com, or www.mtlfab.com.
VENTING TO EXISTING FIREPLACE
In some instances, people desire to convert an
existing fireplace for stove use. Usually, safe con-
nection to an existing masonry chimney requires
more work than using a prefabricated chimney.
The existing fireplace must be closed and sealed at
the damper with high-temperature caulk, ceramic
wool, or furnace cement. Prior to installation, clean
and inspect the existing flue and smoke shelf. In-
stallation should be designed so the system can be
dismantled for periodic cleaning and inspection.
Before conversion, make sure the existing chimney
is structurally sound, the chimney incorporates a
flue liner and make sure it is in good condition.
(A flue liner consists of clay tile that protects the
Continued on next page

VGZ-014 / 20120424.0 Vogelzang International Corp. VG450EL FRONTIERSMAN™ / Page 9
CHIMNEY CONNECTIONS continued …
brickwork of a chimney. If a chimney does not
have a liner, or it is damaged, have it relined by a
professional. DO NOT USE a chimney that is
unlined or damaged!) If you have any ques-
tion regarding the condition of the chimney,
consult a qualified licensed contractor, qualified
engineer, competent mason, certified Chimney
Sweep, or a knowledgable inspector. Consult your
insurance company if you cannot find a qualified
expert.
CAUTION: NOT ALL FIREPLACE
CHIMNEYS ARE SUITABLE FOR
CONVERSION TO ACCOMMODATE
CONNECTION TO A WOOD STOVE.
CHECK WITH A QUALIFIED EXPERT.
Many prefabricated fireplaces are of the “zero-
clearance fireplace” category. These consist of
multilayered metal construction. Connecting a
stove to such a device will void the manufacturer’s
warranty.
Venting a stove directly into a fireplace does
not meet code and should not be attempted. (This
constitutes connection to another appliance - the
fireplace.) Combustion products will be deposited
and build up in the firebox or fireplace. The stove
warranty will be void with such an installation. Do
not create a hazard in your home by connecting in
this manner.
FIG. 10 - Fireplace Conversion
trimwork, ceilings and walls. Positioning the
center of the stove pipe entry into the chimney
24” below the ceiling should insure proper
clearance for a 6” stovepipe.
2. Install a fire clay (5/8˝ minimum thickness)
thimble. Make sure the thimble is flush with
the inner surface of the chimney liner and does
not protrude into the flue (see figure 6).
3. Secure the thimble with refractory mortar. The
thimble should be surrounded by 12˝ of solid
unit masonry brickwork or 24˝ of stone.
4. Install the stovepipe into the thimble as far as
possible without extending past the flue lining
(see figures 4 & 6 on pages 5& 6).
5. A small airspace (about 1/2˝) should remain
between the stovepipe and thimble to allow for
expansion of the pipe. Seal this airspace with
high-temperature caulking or ceramic wool.
6. Secure and seal the damper in the closed posi-
tion using high-temp caulking, ceramic wool,
or furnace cement. Also check to see if the
chimney has a cleanout. If it does, make sure it
is closed and sealed as well. A leaky cleanout
will greatly reduce draft efficiency.
If you have any questions regarding venting
your stove, contact the manufacturer or contact
the National Fire Protection Association (NFPA)
and request a copy of the latest editions of NFPA
Standard 211 and NFPA Standard 908. Their ad-
dress is:
Battery March Park, Quincy, MA 02269.
FIREPLACE INSTALLATION
Directly connecting the stovepipe
into the existing masonry chimney
(figure 10 “Type A” Fireplace Con-
version) of the fireplace is the only
approved method of installation. This
is a complicated and involved process
and to insure safety should only by
done by a qualified installer.
1. An entry hole must be cut through
the masonry and tile liner with
minimal damage to the liner. At
least 8˝ of liner must remain below
the entry position. When locat-
ing the stove and stovepipe, all
minimum clearances must be ob-
served from combustible surfaces
including mantels, combustible
Continued on next page

Page 10 / VG450EL FRONTIERSMAN™ www.vogelzang.com VGZ-014 / 20120424.0
A. Brick Masonry
Minimum 3.5˝/89mm thick brick masonry all framed into com-
bustible wall with a minimum of 12˝/305mm brick separation
from clay liner to combustibles. The fireclay liner shall run
from outer surface of brick wall to, but not beyond, the inner
surface of chimney flue liner and shall be firmly cemented in
place.
B. Insulated Sleeve
Solid-insulated, listed factory-built chimney length of
the same inside diameter as the chimney connector and
having 1˝/25.4cm or more of insulation with a minimum
9˝/229mm air space between the outer wall of the chimney
length and combustibles.
C. Ventilated Thimble
Sheet steel chimney connector, minimum 24 gauge in
thickness, with a ventilated thimble, minimum 24 gauge
in thickness, having two 1˝/25.4mm air channels, sepa-
rated from combustibles by a minimum of 6˝/152mm of glass
fiber insulation. Opening shall be covered, and thimble support-
ed with a sheet steel support, minimum 24 gauge in thickness.
D. Chimney Section Pass-through
Solid insulated, listed factory-built chimney length with an
inside diameter 2˝/51mm larger than the chimney connec-
tor and having 1˝/25.4mm or more of insulation, serving as
a pass-through for a single wall sheet steel chimney con-
nector of minimum 24 gauge thickness, with a minimum
2˝/51mm air space between the outer wall of chimney
section and combustibles. Minimum length of chimney
section shall be 12˝/305mm chimney section spaced
1˝/25.4mm away from connector using sheet steel sup-
port plates on both ends of chimney section. Opening
shall be covered, and chimney section supported on both
sides with sheet steel support securely fastened to wall
surfaces of minimum 24 gauge thickness. Fasteners
used to secure chimney section shall not penetrate
chimney flue liner.
CHIMNEY CONNECTOR SYSTEMS & CLEARANCES

VGZ-014 / 20120424.0 Vogelzang International Corp. VG450EL FRONTIERSMAN™ / Page 11
OPERATING INSTRUCTIONS
THIS STOVE IS DESIGNED TO
BURN WOOD FUEL ONLY!
Hardwood, 14” to 16” should be split and air
dried (seasoned), for 6 months to obtain maximum
burning efficiency. Wood should be stored in a dry,
well ventilated area.
NOTICE: USE SOLID WOOD MATERIALS ONLY.
DO NOT BURN GARBAGE OR FLAMMABLE
FLUIDS. DO NOT USE COALTHIS STOVE IS NOT
DESIGNEDTO ACCOMMODATE THE AIR FLOW
(DRAFT) NECESSARY TO PROPERLY BURN
COAL OR COAL PRODUCTS. DO NOT ELEVATE
FIRE OR USE GRATES OR ANDIRONS. BUILD
FIRE DIRECTLY ON BOTTOM OF FIREBOX.
LIGHTING
1. Open draft damper fully to provide maximum
draft.
2. Open the feed door and place several wads of
crushed paper in the firebox.
3. Lay small stacks of kindling on the paper to
start the fire.
4. Light the paper and kindling, close the door
and secure tightly.
5. Add fuel after fire is burning briskly. Use care
not to smother the kindling fire when adding
wood.
6. Close the door and secure tightly.
7. Adjust the draft damper control. The more
closed the slower the fire will burn. The more
open, the faster and hotter the fire will burn.
8. Do not overfire the stove.
ADDING FUEL
Add small amounts of fuel each hour or so
instead of piling large quantities of fuel at one
time. This will insure a more complete combustion
process and less buildup of tars, soot, or creosote
will occur in the chimney.
1. Always open draft damper before opening the
feed door.
2. When adding fuel be careful not to smother the
fire. Do not build fires against glass on models
with glass door.
CAUTION: HOUSE FIRE HAZARDS
• Do not storewooD on floor pro-
TECTOR, UNDERNEATH STOVEPIPE OR ANY-
WHEREWITHIN MINIMUM CLEARANCES FROM
COMBUSTIBLE SURFACES SPECIFIED FOR
THIS STOVE.
• overfiring may cause a house fire.
YOU ARE OVERFIRING IF A UNIT OR CHIMNEY
CONNECTOR GLOWS RED.
Continued on next page
WARNING: EXPLOSION HAZARD
• never use chemicals, gasoline,
GASOLINE-TYPE LANTERN FUEL, KEROSENE,
CHARCOAL LIGHTER FLUID, OR SIMILAR
FLAMMABLE LIQUIDS TO START OR “FRESH-
EN-UP” A FIRE IN THE STOVE.
• Keep all flammable liquiDs,
ESPECIALLY GASOLINE, OUT OF THE
VICINITY OFTHE HEATER — WHETHER IN USE
OR IN STORAGE.
OPERATING SAFETY PRECAUTIONS
1. NEVER OVERFIRE THIS STOVE BY BUILD-
ING EXCESSIVELY HOT FIRES AS A HOUSE/
BUILDING FIRE MAY RESULT.YOU ARE OVER-
FIRING THE STOVE IF UNIT OR STOVEPIPE
BEGINS TO GLOW OR TURN RED.
2. NEVER BUILD EXTREMELY LARGE FIRES
IN THIS TYPE OF STOVE AS DAMAGE TO THE
STOVE OR SMOKE LEAKAGE MAY RESULT
3. ON MODELS WITH GLASS DOOR, DO NOT
BUILD FIRE TOO CLOSE TO GLASS.
4. UNIT IS HOT WHILE IN OPERATION. KEEP
CHILDREN, CLOTHING, AND FURNITURE
AWAY. CONTACT MAY CAUSE SKIN BURNS. DO
NOT TOUCH THE STOVE AFTER FIRING UNTIL
IT HAS COOLED.
5. PROVIDE AIR INTOTHE ROOM FOR PROP-
ER COMBUSTION.
6. INSPECT STOVEPIPE EVERY 60 DAYS.
REPLACE IMMEDIATELY IF STOVEPIPE IS
RUSTING OR LEAKING SMOKE INTO THE
ROOM.

Page 12 / VG450EL FRONTIERSMAN™ www.vogelzang.com VGZ-014 / 20120424.0
3. Close the feed door and secure tightly.
4. Adjust the draft damper control.
5. Empty ashes regularly. Do not allow ashes to
pile up (see Safety Instructions #14, page 2.)
6. Properly dispose of hot ashes (see Safety
Instructions, item #14 on page 2.)
7. Do not overfire the stove.
CAUTION: DO NOT OVERFIRE APPLIANCE.
TOO MUCH WOOD OR BURNING NON-REC-
OMMENDED MATERIALS SUCH AS TRASH OR
FLAMMABLE LIQUIDS MAY CAUSE OVERFIR-
ING. YOU ARE OVERFIRING IF THE CHIMNEY
CONNECTORS OR STOVE GLOWS RED. CLOSE
THE DOOR AND SHUT DAMPER IMMEDIATELY
TO REDUCE THE AIR SUPPLY TO THE FIRE.
THIS WILL SLOW DOWN THE FIRE.
CAUTION: SLOW BURNING FIRES AND
EXTENDED USE MAY CAUSE EXCESSIVE
CREOSOTE BUILDUP. IGNITION OF CREO-
SOTE BUILDUP OR OVERFIRING MAY CAUSE
A CHIMNEY FIRE. CHIMNEY FIRES BURN
EXTREMELY HOT AND MAY IGNITE
SURROUNDING MATERIALS. IN CASE OF A
CHIMNEY FIRE CALL THE FIRE DEPARTMENT
IMMEDIATELY.
OPERATING continued …
CREOSOTE – FORMATION AND NEED
FOR REMOVAL
CAUTION: RISK OF FIRE WHEN WOOD IS
BURNED SLOWLY, IT PRODUCES TAR AND
OTHER ORGANIC VAPORS, WHICH COMBINE
WITH EXPELLED MOISTURE TO FORM CREO-
SOTE. THE CREOSOTE VAPORS CONDENSE
IN THE RELATIVELY COOL CHIMNEY FLUE
OF A SLOW-BURNING FIRE. AS A RESULT,
CREOSOTE RESIDUE ACCUMULATES ON THE
FLUE LINING.WHEN IGNITEDTHIS CREOSOTE
MAKES AN EXTREMELY HOT FIRE.
THE CHIMNEY CONNECTOR AND CHIMNEY
SHOULD BE INSPECTED AT LEAST ONCE
EVERY TWO MONTHS DURING THE HEATING
SEASON TO DETERMINE IF A CREOSOTE
BUILDUP HAS OCCURRED.
IF CREOSOTE HAS ACCUMULATED (3MM OR
MORE) IT SHOULD BE REMOVED TO REDUCE
THE RISK OF A CHIMNEY FIRE.
Failure to remove creosote may result in igni-
tion and may cause a house/building fire. Creosote
may be removed using a chimney brush or other
commonly available materials from your local
hardware retailer.
Chimney fires burn very hot. If the unit or
chimney connector should glow red, reduce the
fire by closing the inlet air control and immediately
call the fire department.
CAUTION: A CHIMNEY FIRE MAY CAUSE IGNI-
TION OF WALL STUDS OR RAFTERS WHICH
WERE ASSUMED TO BE A SAFE DISTANCE
FROM THE CHIMNEY. IF A CHIMNEY FIRE
HAS OCCURRED, HAVE YOUR CHIMNEY IN-
SPECTED BY A QUALIFIED EXPERT BEFORE
USING AGAIN.
A fire in the firebox may be smothered by pour-
ing a large quantity of coarse salt, baking soda, or
cool ashes on top of the fire.
PREVENTING CREOSOTE BUILDUP
1. Burn with draft damper open for several
minutes at numerous intervals throughout the
day during the heating season, being careful
not to over-fire the unit.
2. BURN ONLY SEASONED WOOD. Avoid
burning wet or green wood. Seasoned wood
has been dried for at least one year.
3. A small fire is preferable to a large smoldering
one that can deposit creosote within the heating
system.
SERVICE HINTS
MAINTENANCE

VGZ-014 / 20120424.0 Vogelzang International Corp. VG450EL FRONTIERSMAN™ / Page 13
SERVICE HINTS
MAINTENANCE continued…
4. Establish a routine for the handling of fuel,
wood burner and firing technique. Check daily
for creosote build-up until experience shows
how often you need to clean for safe operation.
Be aware that the hotter the fire, the less creo-
sote is deposited and weekly cleanings may be
necessary in mild weather even though monthly
cleanings may be enough in colder months.
WARNING: IN CASE OF CHIMNEY FIRE
(1) CLOSE AIR INLET CONTROL (2) GET
OUT OF THE HOUSE (3) CALL THE FIRE
DEPARTMENT.
CHIMNEY DRAFT
The chimney is critical to the proper operation
of the stove. It is the chimney that creates draft;
THE STOVE DOES NOTAND CANNOT CRE-
ATE DRAFT. The chimney provides two vital
functions for proper stove operation. First, it is
the passage to exhaust smoke and hot gases created
in the combustion process. Secondly, it supplies
the draft (or pressure) to bring oxygen to the fire
to sustain combustion. Draft is the natural move-
ment of air or gases through a chimney. Chimney
draft comes from the natural tendency for hot (less
dense) air to rise. As the hot air rises within the
chimney it creates a lower pressure at the bottom of
the chimney to which the stove is connected. The
higher pressure air outside the stove then rushes
into the stove where the lower air pressure level
exists, thus bringing oxygen to the fire. This con-
stant flow of air is referred to as the draft. Many
factors or combination of factors can act together
to build or impede the draft. Without the correct
amount of draft, the stove will not operate properly.
If there is excessive draft, an unsafe condition
will arise with too much air being drawn into the
stove and creating an excessively hot fire. This
could cause over firing which runs the risk of
igniting structural elements around the stove and
chimney.
The most common experience is that of insuf-
ficient draft. Under insufficient draft conditions,
the fire will be starved for oxygen, improper or
incomplete combustion occurs resulting in smoke
spillage into the area around the stove. A fire that
is starved for oxygen will not burn well. Such a
fire will produce excessive smoke that will cool
and condense in the chimney creating creosote.
Excessive amounts of creosote buildup can ignite
causing a chimney fire with the possibility of struc-
tural elements igniting as well.
Correct any draft related issues before using
the stove. The following are some possible causes
of insufficient draft. Please note that one or more
factors may play a role in a draft issue and certain
factors may change over time as conditions vary.
1. Atmospheric Pressure and Air Supply
Atmospheric pressure that affects the draft may
occur from outside the structure, inside the
structure, or both. High pressure weather (clear
and cold) usually produces a better chimney
draft than low pressure (overcast and damp)
conditions. Negative pressure can be created
inside a home by appliances that expel air from
within such as bathroom vents, range hoods,
clothes dryers, and forced air furnaces. Do not
allow such appliances to overcome the natural
draft. Note that newer homes tend to be built
more tightly allowing less make up air to seep
freely in. Negative pressure may be overcome
by opening a nearby door or window. In ex-
treme conditions of negative draft, the airflow
in the chimney will reverse direction. This is
known as “down drafting.”
2. Environmental Factors
Wind or air deflecting off external objects such
as the roof, neighboring structures, trees, or
hills. These can cause a pressure change in the
air surrounding the chimney.
3. Chimney Temperature
The temperature of the chimney is an important
factor in how well it drafts. Warm chimneys
draft better than cold chimneys. This is based
upon the principle that hot air rises while cold
air sinks. Hot gases going up a cold chimney
will cool rapidly. Warm the chimney by allow-
ing a hot fire to burn for the first fifteen to thirty
minutes after starting the fire. Be careful not to
over fire the stove. If any part of the stove or
chimney starts to glow, you are over firing the
stove. Masonry chimneys will take longer to
warm than manufactured chimneys on account
of their greater structural mass. Chimneys
that have a flue diameter larger than the stove
outlet take more heat to warm, thus resulting
in a faster cooling of the hot gases needed to
build or maintain draft.
4. Chimney Installation and Maintenance
Confirm that all four minimum chimney

Page 14 / VG450EL FRONTIERSMAN™ www.vogelzang.com VGZ-014 / 20120424.0
MAINTENANCE
height requirements listed in the Chimney
Connection section of the manual have been
met. The physics that link chimney height with
draft creation are vital to the proper operation
of the stove. Failure to meet each of these
minimum requirements will have an adverse
affect on draft. Avoid long horizontal runs
or multiple elbows. Use stove cement to seal
joints in the connector pipe section. Regularly
clean the chimney, connector pipe, rain cap, and
spark arrestor screen. Creosote build up can
reduce the chimney draw and possibly create
a chimney fire.
5. Temporarily out of Operation
After the fire has burned out, open the air con-
trol to its fully open position. This will allow
warm room air to enter the chimney and keep
it as warm as possible until the stove is used
again.
For assistance involving chimney draft issues, con-
tact a knowledgeable licensed heating and cooling
contractor in your area. For questions regarding
manufactured chimney, contact the manufacturer
of the chimney.
NOTE: A DRAFT READING OF 0.05 TO 0.06 W.C.
(WATER COLUMN) IS REQUIRED FOR PROPER
BURNING OF THIS STOVE.
GLASS CARE
CAUTION: DO NOT OPERATE WITH CRACKED
OR BROKEN GLASS.
Periodic cleaning of glass will be necessary to
prevent accumulations of ash. Acidic ash buildup
can eventually etch and weaken glass. Creosote
accumulations should burn off during hot fires. The
following usage and safety tips should be observed:
1. Inspect the glass regularly for cracks and
breaks. If you detect a crack or break, extin-
guish the fire immediately and contact the
manufacturer for a replacement before re-firing
the stove.
2. Do not slam the door or otherwise impact the
glass. When closing doors, make sure that logs
or other objects do not protrude to impact the
glass.
3. Do not build fires against (or that might fall
against) the glass.
4. Do not clean the glass with materials that
may scratch (or otherwise damage) the glass.
Scratches on the glass can develop into cracks
or breaks during operation.
5. Never attempt to clean the glass while the unit
is hot; allow to dry thoroughly before reuse.
If deposits are not very heavy, normal glass
cleaners are adequate using a soft, non-abrasive
cleaning pad.
6. Never put substances which can ignite explo-
sively in the unit. Even small explosions in
confined areas can blow out the glass.
GLASS REPLACEMENT
WARNING: REPLACE GLASS ONLY WITH 5MM
HIGH TEMPERATURE CERAMIC GLASS OF
THE PROPER SIZE. DO NOT USE SUBSTITUTE
MATERIALS SUCH AS TEMPERED GLASS
OR DOUBLE THICKNESS WINDOW GLASS!
CONTACT THE STOVE MANUFACTURER FOR
REPLACEMENT GLASS.
Gasket and Glass cleaning products are avail-
able at local retail home centers. Manufacturers
of cleaning products include, A.W. Perkins Co.
(www.awperkins.com) or Rutland Products (www.
rutland.com).
Glass Replacement Procedure:
1. Ensure appliance is not in operation and is
thoroughly cooled.
2. Remove screw and glass clips. (See parts list
and diagram.)
3. Remove glass from door frame.
4. If glass is broken, carefully remove and discard
each broken piece to avoid cuts. Discard win-
dow gasket. Replace window and gasket with
original factory replacement parts.
5. Replace new gasket starting at the bottom of
glass working along edges, being sure to center
gasket channel on glass.
6. Trim to length and butt ends together.
7. Perform replacement procedure in reverse order
after replacing glass and gasket.
8. When replacing glass into door, be sure not to
overtighten screws and clips.
DOOR GASKET REPLACEMENT
CAUTION: DO NOT OPERATE A STOVE THAT
IS MISSING DOOR GASKET MATERIAL. OVER
FIRING AND UNSAFE OPERATING CONDI-
TIONS MAY RESULT.
After extensive use, the gasket material which
provides glass and door seal may lose it’s resiliency
and will need to be replaced. Inspect glass and door

VGZ-014 / 20120424.0 Vogelzang International Corp. VG450EL FRONTIERSMAN™ / Page 15
MAINTENANCE
WIRING DIAGRAM - OPTIONAL BLOWER
When ordering missing or replacement parts, always give the Model Number of the stove,
Part Number, and Part Description. Use the illustrations and part lists provided to identify parts.
NOTICE: ALL POWER CORDS
AND ELECTRICAL APPLI-
ANCES AND/OR ASSEMBLIES
MUST BE KEPT OUTSIDE OF
THE CLEARANCE DIMEN-
SIONS SHOWN IN THIS MAN-
UAL FOR COMBUSTIBLE MA-
TERIALS.
gaskets periodically to ensure proper seal; if gas-
kets become frayed or worn, replace immediately.
PROCEDURE:
1. Ensure appliance is not in operation and is
thoroughly cooled.
2. Remove old door gasket and clean channel.
3. Using an approved, high temperature gasket
cement, apply a thin coat in bottom of channel.
4. Starting at hinge side of door, work gasket into
channel around door unit, end butt and trim to
length.
5. Close door and allow three to four hours for
cement to set before firing appliance.
BLOWER MAINTENANCE
The optional blower is maintenance free other than
cleaning. Lightly vacuum motor and air inlet
to keep free of dust and dirt.
NOTICE: ANY REPLACE-
MENT WIRING MUST HAVE
EQUIVALENT INSULA-
TION AND TEMPERATURE
RATING (105°C).
CAUTION: MOVING PARTS CAN CAUSE
INJURY. DO NOT OPERATE WITH COVER
REMOVED.
DANGER:SHOCK HAZARD.DISCONNECT
POWER SOURCE BEFORE INSTALLATION
AND WHENEVER SERVICING BLOWER
ASSEMBLY.

Page 16 / VG450EL FRONTIERSMAN™ www.vogelzang.com VGZ-014 / 20120424.0
ORDERING PARTS - VG450EL FRONTIERSMAN STOVE
When ordering missing or replacement parts, always give the Model Number of the stove,
Part Number, and Part Description. Use the illustrations and part lists provided to identify parts.
Part No. Description Qty. Part No. Description Qty.
16 Legs.............................................................. 4
17 14 mm Nut ................................................... 4
18 Bottom Deflector........................................... 1
19 Firebox Bottom ............................................. 1
20 Firebox.......................................................... 1
21 Rear Deflector .............................................. 1
22 Hardware Pack (not shown) ......................... 1
**Models VG450ELGB only:
32 Complete Blower Assembly, F-4
32a Blower Housing (only) .................................. 1
32b Blower Motor (not shown)............................. 1
32c Blower Power Cord (not shown) ................... 1
32d Cord Strain Relief (not shown) ..................... 1
32e Ceramic Fiber Gasket (not shown)............... 1
33 Air Deflector.................................................. 2
1 Flue Collar .................................................... 1
2 Top Support Rails ......................................... 2
3 Baffle Hangers.............................................. 2
4 Baffle ............................................................ 1
5 Door, Cast Iron ............................................. 1
6 Draft Deflector .............................................. 1
7 Door Latch.................................................... 1
8 Door Handle ................................................. 1
9 Door Header................................................. 1
10 Door Pins...................................................... 2
11 Hearth Plate ................................................. 1
12 Rear Retainer ............................................... 2
13 Side Retainer............................................... 1
14 Fire Bricks.................................................... 14
15 Vented Bricks................................................ 2

VGZ-014 / 20120424.0 Vogelzang International Corp. VG450EL FRONTIERSMAN™ / Page 17
ORDERING PARTS - VG450EL FRONTIERSMAN STOVE
When ordering missing or replacement parts, always give the Model Number of the stove, Part
Number, and Part Description. Use the illustrations and part lists provided to identify parts.
Part No. Description Qty.
23 Door Frame................................................... 1
24 High-Temp Glass .......................................... 1
25 Glass Gasket, 5/8” dia. Fiberglass................ 1
26 Glass Retainer.............................................. 1
27 Retainer Screws ........................................... 3
28 Nuts .............................................................. 2
29 Air Wash Deflector........................................ 1
30 Bolts.............................................................. 2
31 Complete Door Assembly (less handle) ....... 1
Glass replacement instructions for model VG450ELG
CAUTION: WHEN REMOVING BROKEN
GLASS, WEAR THICK GLOVES AND SAFETY
GLASSES. KEEP CHILDREN AWAY AND
DISCARD BROKEN GLASS SAFELY.
1. Be sure stove has cooled before beginning.
2. Using a screwdriver, remove three screws (#27)
and glass retainer (#26).
3. Remove two nuts (#28) and air wash deflector
(#29).
4. Remove glass (#24). Replace with 8”x10”
high-temperature ceramic glass only.
5. Re-install glass reversing steps 1-3. When re-
placing broken glass, remove gasket (#25) from
broken glass and replace around new glass.
WARNING: Do not use substitute materials.
Replace only with original manufacturer
components.
WARNING: Do not slam door or strike glass.
Slamming door or striking glass may cause
glass breakage.
WARNING: Do not use abrasive cleaners on
glass surface. Abrasives may damage the
glass and breakage may occur when heated.
CAUTION: Do not build fire directly against
glass.
CAUTION: Do not operate stove with
broken glass.

Page 18 / VG450EL FRONTIERSMAN™ www.vogelzang.com VGZ-014 / 20120424.0
FLOOR PROTECTOR MATERIAL CALCULATIONS
This stove has been tested for and must be installed on a floor protector with the proper Thermal
Resistance or R-value as stated in the installation instructions on page 3, “Locating Stove” step 1, of
this manual. If the floor protector materials listed in the instructions are not available, materials with
an equivalent R-value may be substituted.
Alternate materials may be rated with C-factor (Thermal Conductance) or k-factor (Thermal
Conductivity) ratings which must be converted to R-value to determine if the alternate material meets
the tested requirements. The following instructions provide the proper information and formulas for
conversion to R-value.
To determine if alternate materials are acceptable follow this sequence.
1. Convert material specifications to R-value:
a. R-value given — no conversion necessary
b. k-factor is given with a required thickness (T) in inches:
R = 1/k x T
c. C-factor is given: R = 1/C
2. Determine the R-value of proposed alternate floor protector:
a. Use formulas in step 1 above to calculate R-value of proposed material(s).
b. For multiple layers, add R-values of each layer to determine overall R-value.
3. If the overall R-value of the floor protector system is equal to or greater than the floor protector
specifications given, the alternate is acceptable.
Definitions:
Thermal conductance(C) = BTU =W
(hr)(ft2)(°F) (m2)(°K)
Thermal conductivity (k) = (Btu)(inch) =W =Btu
(hr)(ft2)(°F) (m)(°K) (hr)(ft)(°F)
Thermal resistance (R) = (ft2)(hr)(°F) =(m2)(°K)
Btu W
Example:
The specs of floor protector material should be 3/4-inch thick material with a k-factor of 0.84.
The proposed alternative material is 4” brick with a C-factor of 1.25 over 1/8-inch mineral board
with a k-factor of 0.29.
Step 1: Convert specs to R-value.
R = 1/k x T = 1/0.84 x 0.75 = 0.893 System must have a R-value of 0.893 = Rspecs
Step 2: Calculate R-value of individual components
4” Brick with C-factor = 1.25. R = 1/C = 1/1.25 = 0.80 = Rbrick
1/8-inch (0.125”) mineral board with k-factor = 0.29. R = 1/0.29 x 0.125 = 0.431 = Rmin.brd.
Step 3: Add R-values of components to get total R-value of system
Rbrick + Rmin.brd = 0.80 + 0.431 = 1.231 = Rsystem
Step 4: Compare Rsystem to Rspecs
Rsystem = 1.231 is larger than Rspecs of 0.893. System R-value exceeds the required
specifications and therefore is an acceptable alternative.

VGZ-014 / 20120424.0 Vogelzang International Corp. VG450EL FRONTIERSMAN™ / Page 19
CHIMNEY & STOVE MAINTENANCE LOG
DATE OF SERVICE PERFORMED BY DESCRIPTION

Page 20 / VG450EL FRONTIERSMAN™ www.vogelzang.com VGZ-014 / 20120424.0
Vogelzang International Corporation
400 West 17th Street
Holland, Michigan 49423
www.vogelzang.com
Phone:[phone]
Fax: [phone]
COMPANY TESTIMONY:
“FOR GOD SO LOVED THE WORLD THAT HE GAVE HIS ONLY BEGOTTEN SON, THAT WHOEVER
BELIEVES IN HIM SHALL NOT PERISH BUT HAVE ETERNAL LIFE”
JOHN 3:16
MADE IN CHINA
This Vogelzang heating appliance is safe when installed properly and will provide you with years of
service. However, always exercise good judgement when you are using this stove.You are dealing with
FIRE! Fire is inherently dangerous and must be treated with respect. Stay warm and in good health!
Respectfully yours,
SteveVogelzang
Proprietor
DO not USE THIS STOVE IN A
MOBILE HOME, MANUFACTURED HOME,
TRAILER OR TENT — NO EXCEPTIONS!