Vogelzang International VG650ELG User manual

VGZ-025 | 201110519.0 Vogelzang International Corp. VG650ELG MOUNTAINEER™ | Page 1
READ ALL INSTRUCTIONS CAREFULLY
BEFORE STARTING THE INSTALLATION
OR OPERATINGTHE STOVE. FAILURE TO
FOLLOW INSTRUCTIONS MAY RESULT IN
PROPERTY DAMAGE, BODILY INJURY, OR
EVEN DEATH.
DO NOT USE THIS STOVE IN A MOBILE
HOME, MANUFACTURED HOME, TRAILER
OR TENT — NO EXCEPTIONS!
This stove meets
U.S. Test Standard:
UL 1482-1996
SAFETY INSTRUCTIONS
SAFETY NOTICE: IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE/BUILDING FIRE
MAY RESULT. FOR YOUR SAFETY, CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT
PERMITS, RESTRICTIONS, AND INSTALLATION REQUIREMENTS FOR YOUR AREA.
READ ALL INSTRUCTIONS CAREFULLY.
1. The installation of this stove must comply
with your local building code rulings. Please
observe the clearances to combustibles (see
reference figures 7– 9). Do not place furni-
ture or other objects within the clearance
area.
2. Verify that the stove is properly installed
before firing the stove for the first time.
After reading these instructions, if you have
any doubt about your ability to complete
your installation properly, you must ob-
tain the services of a professional licensed
installer familiar with all aspects of safe
and correct installation. DO NOT use
temporary or makeshift compromises
during installation.
3. DO NOT store wood, flammable liquids
or other combustible materials too close to
the unit. Refer to certification label on back
of unit and reference figures 7 – 9 in this
manual.
4. DO NOT INSTALL THIS STOVE
IN A MOBILE HOME, MANUFAC-
TURED HOME, TRAILER OR TENT
NO EXCEPTIONS! (HUD Federal Standard:
24 CFR Ch.XX).
5. If any parts are missing or defective, please
notify the dealer or manufacturer immediately.
DO NOT OPERATE A STOVE THAT IS
MISSING ANY PARTS!
6. Do not tamper with combustion air control
beyond normal adjustment capacities.
7. Always connect this stove to a chimney and
vent to the outside. Never vent to another
room or inside a building. DO NOT CON-
NECT THIS UNIT TO A CHIMNEY FLUE
SERVING ANOTHER APPLIANCE.
8. DO NOT CONNECT a wood burning stove
to an aluminum Type B gas vent. This is not
safe. Use code-approved lined masonry or
a UL 103 HT Listed Residential Type and
Building Heating Appliance chimney. Use
a 6” diameter chimney or larger, that is high
enough to give a good draft. (See specifics in
installation instructions).
Vogelzang International Corporation
400 West 17th Street
Holland, Michigan 49423
www.vogelzang.com
Phone: [phone]
Fax: [phone]
MOuNTaiNeer™WOOdsTOve
Model VG650ELG Owners Manual
(save this manual for future reference)
continued on next page

Page 2 | VG650ELG MOUNTAINEER™ www.vogelzang.com VGZ-025 | 201110519.0
9. Be sure that your chimney is safely constructed
and in good repair. Have the chimney inspected
by the fire department or a qualified inspector.
Your insurance company should be able to
recommend a qualified inspector.
10. Creosote or soot may build up in the chimney
connector and chimney and cause a house/
building fire. Inspect the chimney connector
and chimney twice monthly during the heating
season and clean if necessary. (See Chimney
Maintenance, page 14).
11. In the event of a chimney fire, turn the
damper to closed position, leave the build-
ing and CALL THE FIRE DEPARTMENT
IMMEDIATELY! Have a clearly understood
plan on how to handle a chimney fire by con-
tacting your local fire authority for information
on proper procedures in the event of a chimney
fire.
12. To prevent injury, do not allow anyone to use
this stove who is unfamiliar with the correct
operation of the stove.
13. Do not operate stove while under the
influence of drugs or alcohol.
14. Ashes should not be allowed to accumulate
above sides of ash drawer. Dispose of ashes in
a metal container with a tight fitting lid. Keep
the closed container on a noncombustible floor
or on the ground, well away from all combus-
tible materials. Keep the ashes in the closed
container until all cinders have thoroughly
cooled. The ashes may be buried in the ground
or picked up by a refuse collector.
15. The special paints used on your stove may
give off some smoke and an odor while
they are curing during the first 12 to 15 fires.
Additional smoke and odor may be emitted
from the light oils used in construction of the
fire box. This should disappear after a short
period of time and not occur again. Persons
with lung conditions or owners of susceptible
domestic pets (such as birds) should take
prudent precautions. Open windows and
doors as needed to clear smoke and/or odor.
Paint discoloration will occur if the stove is
over fired.
16. This stove has a painted surface which
is durable but it will not stand rough handling
or abuse. When installing your stove, use care
in handling. Clean with soap and warm water
when stove is NOT hot. Do not use any acids
SAFETY INSTRUCTIONS continued…
or scouring soap, as these solvents wear and
dull the finish.
17. While stove is in operation, all persons,
especially young children should be alerted to
the hazards from high surface temperatures.
Keep away from a hot stove to avoid burns or
clothing ignition.
18. The walls of the firebox may become slightly
distorted after a period of use. A slight distor-
tion will not affect the operation of the stove.
19. If small children will be in the same room
as the stove during operation, provide a
sturdy barrier to keep them at a safe distance
from the stove. NEVER LEAVE SMALL
CHILDREN UNSUPERVISED when they
are in the same room as the stove.
20. Keep stove area clear and free from all
combustible materials, gasoline, and other
flammable vapors and liquids.
21. To prevent burns always wear protective
clothing, leather hearth gloves and eye
protection, while tending the fire.
22. While in operation, keep the ash cleanout cover
in place. Keep the feed door closed and secured
at all times except while tending the fire.
23. Do not over fire the stove. Over firing will
occur if the feed door or ash clean-out cover
are left open during operation. Such actions can
result in very dangerous operating conditions.
24. DO NOT ELEVATE FIRE! Build fire directly
on the bottom of the firebox. This stove has not
been tested with the use of grates, andirons, or
other means of elevating fire and should not be
used.
25. All power cords and electrical appliances
and/or assemblies must be kept outside of the
clearance dimensions shown in this manual for
combustible materials.
26. For further information on using your stove
safely, obtain a copy of the National Fire
Protection Association (NFPA) publication,
“Using Coal and Wood Stoves Safely” NFPA
No. HS-10-1978. The address of the NFPA is
Batterymarch Park, Quincy, MA 02269.
NOTE: A PROFESSIONAL, LICENSED HEAT-
ING AND COOLING CONTRACTOR MUST
BE CONSULTED IF YOU HAVE QUESTIONS
REGARDING THE INSTALLATION OF THIS
SOLID FUEL BURNING APPLIANCE.

VGZ-025 | 201110519.0 Vogelzang International Corp. VG650ELG MOUNTAINEER™ | Page 3
ASSEMBLY INSTRUCTIONS
NOTICE: Vogelzang International Corp. grants no warranty, stated or implied, for the installation or maintenance of
your wood stove and assumes no responsibility of any incidental or consequential damages.
t o o l s
TOOLS AND MATERIALS REQUIRED FOR INSTALLATION

 
 
 
 
 
 
 
 
m a t e r i a l s
(NOTE: The following items are NOT included with your stove)



 


Furnace Cement (manufacturer recommends Rutland Code 78

CAUTION: STOVE IS HEAVY. MAKE SURE YOU
HAVE ADEQUATE HELP AND USE PROPER
LIFTING TECHNIQUES WHENEVER MOVING
STOVE.
1. Uncrate the stove and remove all cardboard
and styrofoam packing materials and protective
poly bag. Remove rear deflector (#2), pedestal
base (#18) and pedestal top (#14) from the car-
ton. (Save cardboard for further assembly.)
2. Remove parts from inside stove. Parts include:
damper (#5), damper collar (#4), blower assem-
bly (#3), ash drawer (#13), pedestal front (#17),
pedestal sides (#15), pedestal drawer support
(#16), and hardware pack (#19) located inside
firebox.
5. Insert the pedestal drawer support (#16) into the
pedestal assembly. Secure with two (2) sheet
metal screws from the back of the assembly.
3. Using machine
screws, lock
washers and hex
nuts, attach the
pedestal sides
(#15) to the ped-
estal base (#18),
figure 1.
4. Attach the front panel (#17) of the pedestal base
assembly to the sides. Notice: the front panel
fits over the sides, figure 2. Attach the front
panel to the side panels with machine screws,
lockwashers and hex nuts (three each side).
Figure 1
Figure 2 Attach Front
Panel to Side Panels.
Figure 3 Insert the
Drawer Support inside the
pedestal base assembly
6. Attach the top plate to the pedestal assembly,
figure 4, with machine screws, lockwashers and
hex nuts.
Figure 4 Attach the
Top Plate to the pedestal
base assembly.
continued on next page

Page 4 | VG650ELG MOUNTAINEER™ www.vogelzang.com VGZ-025 | 201110519.0
CAUTION: STOVE BODY IS HEAVY. MAKE
SURE YOU HAVE ADEQUATE HELP TO LIFT
STOVE BODY AND PEDESTAL AND USE PROP-
ER LIFTING TECHNIQUES.
7. Place flattened carton on floor and carefully
tip the stove box assembly (#1) onto it’s back.
Prop up the bottom edge with additional pack-
ing material or wood pieces.
8. Tip the pedestal base assembly back and align
the four mounting holes in the top plate of the
pedestal base assembly to the mounting studs
in the bottom of the stove box. Secure with hex
nuts and tighten. NOTE: By design the pedestal
base is open on the back side to help dissipate
heat.
9. Carefully lift the stove to the upright posi-
tion.
10. Insert the ash drawer (#13) into the pedestal
base
11. After properly locating flooring protector
(figure 7, page 5) to accommodate minimum
stove clearances, place stove in position on
floor protector.
12. Attach rear deflector (#2) to the rear side cor-
ners of the stove using four screws provided.
13. Attach blower assembly (#3) to back of rear
deflector. NOTE: Make sure ceramic gasket
(#26) is positioned between rear deflector and
blower assembly and is properly aligned so it
doesn’t block the fan, Figure 5.
14. Install damper (#5) into damper collar (#4) [see
damper installation below] and secure to top
surface of stove using machine screws.
Figure 5 Align Ceramic
Gasket with blower fan
opening before mounting.
ASSEMBLY INSTRUCTIONS continued
DAMPER INSTALLATION
Fig. 6 – Cast Iron Damper
1. Position collar onto hole in stove top and align
the mounting holes.
2. Secure the collar to stove with bolts and nuts
supplied (figure 6).
3. Install damper into collar as shown in lower
illustration (figure 6).
4. Insert damper handle through collar into
damper and out the opposite side of collar.
Bolt
Nut
Damper
Collar
Stove T o p

VGZ-025 | 201110519.0 Vogelzang International Corp. VG650ELG MOUNTAINEER™ | Page 5
LOCATING STOVE continued
1. The stove must be placed on solid concrete, sol-
id masonry, or when installed on a combustible
floor, on a listed floor protector, such as Hy-C
or Imperial Model UL4848BK or equivalent
with 1.0 R-factor. (NOTE: to calculate R-value
of alternative materials see page 17). The base
must extend at least 16˝ beyond the front of the
access door, 8˝ to the sides, 8˝ behind and must
extend under and 2 inches beyond either side of
the stove pipe if it is elbowed towards a wall.
(See figures 7 & 9 and consult local building
codes and fire protection ordinances.)
CAUTION: (FIRE HAZARD) CARPETING AND
OTHER COMBUSTIBLE MATERIAL MUST NOT
COVER THE FLOOR PROTECTOR. THESE
MATERIALS MUST REMAIN OUTSIDE OF
COMBUSTIBLE CLEARANCES, SEE FIG. 7– 9.
2. The stove must have its own flue. DO NOT
CONNECT THIS UNIT TO A CHIMNEY
FLUE SERVING OTHER APPLIANCES.
3. After observing the clearances to combus-
tible materials (figures 7–9), locate your floor
protector accordingly (figure 7) and care-
fully place the stove in your selected location.
Install connector pipe, elbows, and thimble as
required, utilizing either a recently cleaned
and inspected 6” masonry chimney or a 6”
i.d. listed chimney.
4. Use round 6” dia., minimum 24 MSG (mini-
mum standard gauge) black or 26 MSG blue
Fig. 7 – TOP VIEW Minimum Clearance Dimensions from Combustible Surfaces
FLOOR
PROTECTOR
DASHED LINES SHOW HORIZONTAL CHIMNEY CONNECTOR
AND ADDITIONAL FLOOR PROTECTOR REQUIRED BENEATH
AND EXTENDING 2” BEYOUND EACH SIDE
COMBUSTIBLE CONSTRUCTION IN ACCORDANCE WITH NFPA 211
BACKWALL
SIDEWALL
8"min.
17"
48"
16"min.
8"min.28"
25"
min.
26"min
MINIMUM CLEARANCES TOP VIEW
44"
Volgelzang
VG650
Use 48"x 48"
Standard Size
Floor Protector
steel stove pipe. DO NOT use galvanized
stove pipe. Secure pipe sections with three
(3) sheet metal screws in each stove pipe and/
or elbow joint to firmly hold the pipe sections
together. DO NOT CONNECTTHIS STOVE
TO ANY AIR DISTRIBUTION OR DUCT
SYSTEM.
5. Recheck clearances from the stove,
connector stove pipe, and corner clearances
using the illustrations in figures 7–9 and
your local building codes or fire protection
ordinances.
NOTE: A wall faced with drywall, brick
or stone must be considered a combustible
surface.
6. D o N o t i N s ta l l t h i s s t o v e i N
a mobile home, maNufactureD home,
teNt or trailer – NO EXCEPTIONS!
(HUD Federal Standard: 24 CFR Ch.xx)
7. The clearances provided are minimum
dimensions determined by Intertek Testing
Services, the manufacturer’s testing laboratory.
Installation of this stove must comply with the
latest edition of NFPA 211 for reduced clear-
ances and/or your local building code rulings.
Use whichever minimum dimensions are
LARGEST.
8. This stove meets U.S. Test Standard:
UL 1482-1996.
continued on next page

Page 6 | VG650ELG MOUNTAINEER™ www.vogelzang.com VGZ-025 | 201110519.0
LOCATING STOVE continued…
Fig. 9a – Front View
Minimum Clearance Dimensions
from Combustible Surfaces
Fig. 9b – Side View
Minimum Clearance Dimensions
from Combustible Surfaces
CAUTION: KEEP FURNISHINGS AND OTHER
COMBUSTIBLE MATERIALS AWAY FROM THE
STOVE.
NOTE: BEFORE FIRING WOODSTOVE SLIDE
FIREBRICKS TOWARDS THE REAR SO NO
GAPS REMAIN BETWEEN BRICKS.
18-1/2"
18-1/2"
CORNER CLEARANCES
Fig. 8 – Top View
Minimum Corner Clearances
from Combustible Surfaces

VGZ-025 | 201110519.0 Vogelzang International Corp. VG650ELG MOUNTAINEER™ | Page 7
PIPE CONNECTOR INSTALLATION
1. The crimped end of the stovepipe fits inside
the stove flue collar. Install additional pipe and
elbow with the crimped end towards the stove.
This will allow any condensation in the flue to
run back into the firebox.
2. Horizontal pipe runs must slope upwards
towards the chimney at least 1/4” per foot of
horizontal run.
3. You must have at least 18 inches of clearance
between any horizontal piping and the ceil-
ing.
4. The pipe cannot extend into the chimney flue
(figure 10).
5. Secure pipe/elbow sections with three (3) sheet
metal screws at each joint to make the piping
rigid.
6. It is recommended that no more than two (2)
90° bends be used in the stovepipe installa-
tion. The use of more than two 90° bends may
decrease the amount of draw and possibly
cause smoke spillage. Where possible, use only
corrugated (nonadjustable) elbows. These
provide a better seal.
7. The connector pipe must not pass through an
attic or roof space, closet, or any concealed
space, or floor, ceiling, wall or combustible
construction. (See Chimney Connector Sys-
tems & Clearances, page 18). A UL 103 HT
Listed chimney must be used from the first
penetration of ceiling or wall to the chimney
cap.
CAUTION: NEVER USE SINGLE WALL CON-
NECTOR PIPE AS A CHIMNEY - A HOUSE FIRE
COULD RESULT.
Fig. 10 – Stovepipe/Flue Connections
CORRECT WRONG WRONG
NOTE: STOVE PIPE IS NOT INCLUDED. TO
PURCHASE,VISITYOUR LOCAL HARDWARE,
HOME OR BUILDING CENTER. USE ROUND
minimum standard
gauge) BLACK OR 26 MSG BLUE STEEL
STOVE PIPE. DO NOT USE GALVANIZED
STOVE PIPE.

Page 8 | VG650ELG MOUNTAINEER™ www.vogelzang.com VGZ-025 | 201110519.0
MASONRY CHIMNEY
Before using an existing masonry chimney,
clean the chimney, inspect the flue liner and make
any repairs needed to be sure it is safe to use. Make
repairs before attaching the stove. The connec-
tor stove pipe and fittings you will need to con-
nect directly to a masonry chimney are shown in
figure 11.
CHIMNEY CONNECTIONS
The stove must be connected to either a ma-
sonry or manufactured metal chimney built and
tested to the specifications listed on the previous
pages.
Chimneys perform two functions:
1). As a means of exhausting smoke and flue
gases which are the result of fuel combustion.
2). The chimney provides “draft” which allows
oxygen to be continuously introduced into the
appliance, so that proper combustion is possible.
This stove relies on natural draft to operate.
NOTICE: Always provide a source of fresh air
into the room where the stove is located. Failure
to do so may result in air starvation of other fuel
burning appliances and the possible development
of hazardous conditions, fire or death.
Your stove itself does not create draft. Draft is
provided by the chimney. To achieve proper draft
your chimney must meet the three minimum height
requirements detailed in figures 12–14.A minimum
of 0.05 w.c. (measured in water column) is required
for proper drafting to prevent back puffing, smoke
spillage, and to maximize performance. (Gauges to
measure draft are readily available at stove stores
and are economical to rent or purchase.)
Factors such as wind, barometric pressure,
trees, terrain and chimney temperature can have
an adverse effect on the draft. The manufacturer
cannot be held responsible for external factors
leading to less than optimal drafting.
Should you have a problem with inadequate
draft, you should contact a licensed heating and
cooling contractor for assistance in solving the
problem.
IMPORTANT Installation Points
1. Size chimney flue to stove collar. This stove
requires a 6” diameter flue.
2. Never connect this unit to a chimney serv-
ing another appliance.
3. The chimney must meet all minimum
height requirements.
4. Never use a chimney to ventilate a cellar
or basement.
5. Contact your local building authority
for approved methods of installation and any
necessary permits and/or inspections.
Fig. 12 - Chimney Construction Through Attic Space
Fig. 11 - Masonry Chimney Connection
If the connector stove pipe must go through
a combustible wall before entering the masonry
chimney, consult a qualified mason or chimney
dealer. The installation must conform to local
building and fire codes and latest edition of NFPA
211.
If there is a cleanout opening in the base of the
chimney, close it tightly.
CHIMNEY
FLUE
5/8" TILE
CHIMNEY
LINER
MASONRY
CHIMNEY
THIMBLE
COLLAR
6˝ ROUND
24 ga. BLACK
STOVEPIPE
8˝ MIN.
LINER
BELOW
ENTRY
HOLE

VGZ-025 | 201110519.0 Vogelzang International Corp. VG650ELG MOUNTAINEER™ | Page 9
Fig. 13 - Chimney Construction Through Roof
Fig. 14 - Chimney Connection to Firebox
Through Masonry Wall
CHIMNEY CONNECTIONS continued …
MANUFACTURED CHIMNEY
REFER TO CHIMNEY AND CHIMNEY
CONNECTOR MAKER’S INSTRUCTIONS FOR
INSTALLATION AND USE.
Use only 6” diameter listed chimney UL 103
HT. Chimney made to this listing is High Tempera-
ture rated to 2100 degrees Fahrenheit. Use chimney
from only one manufacturer. Never mix brands.
Carefully follow the chimney manufacturer’s stated
requirements and clearances. Use the chimney
manufacturer’s attic guards, roof supports, flashing
and fire stops when passing through a ceiling. Use a
listed thimble when passing through a combustible
wall. Do not use makeshift compromises during
installation. Never use a single-wall connection
pipe as a chimney!
When using a pre-existing chimney, have it’s
condition and installation inspected before using.
Make sure that the chimney meets all of the UL
rating requirements listed above. Be aware that
not all manufactured chimney is of the UL 103
HT type.
NOTE: It is recommended that you contact a li-
censed heating and cooling contractor (consult your
local yellow pages) for chimney installation.
Manufactured chimney with the proper required
UL listing is available from most home centers,
hardware stores, and HVAC supply stores.
If you have access to the internet, you may
wish to view chimney manufacturers’ informa-
tion on-line. See, www.duravent.com, www.
selkirkinc.com, or www.mtlfab.com.
VENTING TO EXISTING FIREPLACE
In some instances, people desire to convert an
existing fireplace for stove use. Usually, safe con-
nection to an existing masonry chimney requires
more work than using a prefabricated chimney.
The existing fireplace must be closed and sealed at
the damper with high-temperature caulk, ceramic
wool, or furnace cement. Prior to installation, clean
and inspect the existing flue and smoke shelf. In-
stallation should be designed so the system can be
dismantled for periodic cleaning and inspection.
Before conversion, make sure the existing chimney
is structurally sound, the chimney incorporates a
flue liner and make sure it is in good condition.
continued on next page

Page 10 | VG650ELG MOUNTAINEER™ www.vogelzang.com VGZ-025 | 201110519.0
CHIMNEY CONNECTIONS continued …
(A flue liner consists of clay tile that protects the
brickwork of a chimney. If a chimney does not
have a liner, or it is damaged, have it relined by
a professional. DO NOT USE a chimney that is
unlined or damaged!) If you have any question
regarding the condition of the chimney, consult a
qualified licensed contractor, qualified engineer,
competent mason, certified Chimney Sweep, or a
knowledgable inspector. Consult your insurance
company if you cannot find a qualified expert.
CAUTION: NOT ALL FIREPLACES ARE SUIT-
ABLE FOR CONVERSION TO A WOOD STOVE.
CHECK WITH A QUALIFIED EXPERT.
Many prefabricated fireplaces are of the
“zero-clearance fireplace” category. These consist
of multilayered metal construction. They are de-
signed with enough insulation and/or air cooling
on the base, back and sides so they can be safely
installed in direct contact with combustible floors
and walls. Although many prefabricated fireplaces
carry endorsements from nationally recognized
organizations for use as fireplaces, they have not
been tested for connection to wood stove heaters.
Connecting a stove to such a device will void the
manufacturer’s warranty.
Steel-lined fireplaces are constructed with
1/4” firebox liner, an air chamber in connection
with 8” of masonry. These can be safely used
with wood burning stoves. They contain all the
FIG. 15 - Fireplace Conversion
FIREPLACE INSTALLATION
Directly connecting the stovepipe into the exist-
ing masonry chimney (figure 15 “Type A” fireplace
conversion) of the fireplace is the only approved
method of installation. This is a complicated and
involved process and to insure safety should only
by done by a qualified installer.
1. An entry hole must be cut through the masonry
and tile liner with minimal damage to the liner.
At least 8” of liner must remain below the entry
position. When locating the stove and stove-
pipe, all minimum clearances must be observed
from combustible surfaces including mantels,
combustible trimwork, ceilings and walls.
Positioning the center of the stove pipe entry
into the chimney 24” below the ceiling should
insure proper clearance for a 6” stovepipe.
2. Install a metal or fire clay (5/8” minimum thick-
ness) thimble. Make sure the thimble is flush
with the inner surface of the chimney liner and
does not protrude into the flue (see figure 10
on page 7).
3. Secure the thimble with refractory mortar. The
thimble should be surrounded by 8” of solid
unit masonry brickwork or 24” of stone.
4. Install the stovepipe into the thimble as far as
possible without extending past the flue lining
(see figures 10 & 11 on pages 7 & 8).
5. A small airspace (about 1/2”) should remain
between the stovepipe and thimble to allow for
expansion of the pipe. Seal this airspace with
high-temperature caulking or ceramic wool.
essential components of a fireplace,
firebox, damper, throat, smoke shelf,
and smoke chamber. Many look identi-
cal to masonry fireplaces and should be
checked carefully before connecting a
stove to them.
Venting a stove directly into a fire-
place does not meet code and should not
be attempted. (This constitutes connec-
tion to another appliance - the fireplace.)
Combustion products will be deposited
and build up in the firebox or fireplace.
The stove warranty will be void with
such an installation. Do not create a
hazard in your home by connecting in
this manner.
Continued on next page

VGZ-025 | 201110519.0 Vogelzang International Corp. VG650ELG MOUNTAINEER™ | Page 11
OPERATING INSTRUCTIONS
This stove is designed to burn
WOOD FUEL ONLY!
Hardwood, 16” to 18” should be split and air
dried (seasoned), for 6 months to obtain maximum
burning efficiency. Wood should be stored in a dry,
well ventilated area.
NOTICE: USE SOLID WOOD MATERIALS ONLY.
DO NOT BURN GARBAGE OR FLAMMABLE
FLUIDS. DO NOT USE COALTHIS STOVE IS NOT
DESIGNEDTO ACCOMMODATETHE AIR FLOW
(DRAFT) NECESSARY TO PROPERLY BURN
COAL OR COAL PRODUCTS. DO NOT ELEVATE
FIRE OR USE GRATES OR ANDIRONS. BUILD
FIRE DIRECTLY ON BOTTOM OF FIREBOX.
LIGHTING
1. Open draft damper fully to provide maximum
draft.
2. Open the feed door and place several wads of
crushed paper in the firebox.
3. Lay small stacks of kindling on the paper to
start the fire.
4. Light the paper and kindling, close the door
and secure tightly.
5. Add fuel after fire is burning briskly. Use care
not to smother the kindling fire when adding
wood.
CAUTION: HOUSE FIRE HAZARDS
 -
TOR, UNDERNEATH STOVEPIPE OR ANY-
WHEREWITHIN MINIMUM CLEARANCES FROM
COMBUSTIBLE SURFACES SPECIFIED FOR
THIS STOVE.
       
YOU ARE OVER FIRING IF A UNIT OR CHIMNEY
CONNECTOR GLOWS RED.
OPERATING SAFETY PRECAUTIONS
1. NEVER OVER FIRE THIS STOVE BY BUILD-
ING EXCESSIVELY HOT FIRES AS A HOUSE/
BUILDING FIRE MAY RESULT.YOU ARE OVER-
FIRING THE STOVE IF UNIT OR STOVEPIPE
BEGINS TO GLOW OR TURN RED.
2. NEVER BUILD EXTREMELY LARGE FIRES
IN THIS TYPE OF STOVE AS DAMAGE TO THE
STOVE OR SMOKE LEAKAGE MAY RESULT
3. ON MODELS WITH GLASS DOOR, DO NOT
BUILD FIRE TOO CLOSE TO GLASS.
4. UNIT IS HOT WHILE IN OPERATION. KEEP
CHILDREN, CLOTHING, AND FURNITURE AWAY.
CONTACT MAY CAUSE SKIN BURNS. DO NOT
TOUCH THE STOVE AFTER FIRING UNTIL IT
HAS COOLED.
5. PROVIDE AIR INTO THE ROOM FOR PROP-
ER COMBUSTION.
6. INSPECT STOVEPIPE EVERY 60 DAYS.
REPLACE IMMEDIATELY IF STOVEPIPE IS
RUSTING OR LEAKING SMOKE INTO THE
ROOM.
6. Secure and seal the damper in the closed posi-
tion using high-temp caulking, ceramic wool,
or furnace cement. Also check to see if the
chimney has a cleanout. If it does, make sure it
is closed and sealed as well. A leaky cleanout
will greatly reduce draft efficiency.
If you have any questions regarding venting
your stove, contact the manufacturer or contact
the National Fire Protection Association (NFPA)
and request a copy of the latest editions of NFPA
Standard 211 and NFPA Standard 908. Their ad-
dress is:
Battery March Park, Quincy, MA 02269.
CHIMNEY C0NNECTIONS continued …
continued on next page
WARNING: EXPLOSION HAZARD
    
GASOLINE-TYPE LANTERN FUEL, KEROSENE,
CHARCOAL LIGHTER FLUID, OR SIMILAR
FLAMMABLE LIQUIDS TO START OR “FRESH-

    
ESPECIALLY GASOLINE, OUT OF THE
VICINITY OFTHE HEATER —WHETHER IN USE
OR IN STORAGE.

Page 12 | VG650ELG MOUNTAINEER™ www.vogelzang.com VGZ-025 | 201110519.0
6. Close the door and secure tightly.
7. Adjust the draft damper control. The more
closed the slower the fire will burn. The more
open, the faster and hotter the fire will burn.
8. Do not over fire the stove.
ADDING FUEL
Add small amounts of fuel each hour or so
instead of piling large quantities of fuel at one
time. This will insure a more complete combustion
process and less buildup of tars, soot, or creosote
will occur in the chimney.
1. Always open draft damper before opening the
feed door.
2. When adding fuel be careful not to smother the
fire. Do not build fires against glass on models
with glass door.
3. Close the feed door and secure tightly.
4. Adjust the draft damper control.
5. Empty ashes regularly. Do not allow ashes
to pile up (see Safety Instructions #14 on
page 2.)
6. Properly dispose of hot ashes (see Safety
Instructions, item #14 on page 2.)
7. Do not over fire the stove.
CAUTION: DO NOT OVER FIRE APPLIANCE.
YOU ARE OVER FIRING IF THE CHIMNEY
CONNECTORS OR STOVE GLOWS RED. CLOSE
THE DOOR AND SHUT FLUE DAMPER IMME-
DIATELY TO REDUCE THE AIR SUPPLY TO THE
FIRE. THIS WILL SLOW DOWN THE FIRE.
CAUTION: SLOW BURNING FIRES AND
EXTENDED USE MAY CAUSE EXCESSIVE
CREOSOTE BUILDUP. IGNITION OF CREO-
SOTE BUILDUP OR OVERFIRING MAY CAUSE
A CHIMNEY FIRE. CHIMNEY FIRES BURN
EXTREMELY HOT AND MAY IGNITE
SURROUNDING MATERIALS. IN CASE OF A
CHIMNEY FIRE CALL THE FIRE DEPARTMENT
IMMEDIATELY.
OPERATING continued … OPERATING TIPS

1. Burn with air control open for several minutes
at numerous intervals throughout the day dur-
ing the heating season, being careful not to
over-fire the unit.
2. Burn stove with flue damper wide open for sev-
eral minutes every time you apply fresh wood.
This allows wood to achieve the charcoal stage
faster and burns wood vapors which might
otherwise be deposited as creosote within the
heating system.
3. BURN ONLY SEASONED WOOD. Avoid
burning wet or green wood. Seasoned wood
has been dried for at least one year.
4. A small fire is preferable to a large smoldering
one that can deposit creosote within the heating
system.
5. Establish a routine for the handling of fuel,
wood burner and firing technique. Check daily
for creosote build-up until experience shows
how often you need to clean for safe operation.
Be aware that the hotter the fire, the less creo-
sote is deposited and weekly cleanings may be
necessary in mild weather even though monthly
cleanings may be enough in colder months.
WARNING: IN CASE OF CHIMNEY FIRE
(1) CLOSE AIR INLET CONTROL (2) GET OUT
OF THE HOUSE (3) CALL THE FIRE DEPART-
MENT.
SERVICE HINTS
CHIMNEY DRAFT
Draft is a function of the chimney, not the
stove — do not expect the stove to draw. Smoke
spillage into the house or excess buildup of conden-
sation or creosote in the chimney are warnings that
the chimney is NOT functioning properly. Correct
the problem before using the stove. Following are
some possible causes for improper draft.
1. The connector stovepipe may be pushed
into the chimney too far, stopping the draft.
2. If the chimney is operating too cool, water
will condense in the chimney and run back into the
stove. Creosote formation will be rapid and may
block the chimney. Operate the stove at a fire level
high enough to keep the chimney warm preventing
this condensation.

VGZ-025 | 201110519.0 Vogelzang International Corp. VG650ELG MOUNTAINEER™ | Page 13
SERVICE HINTS continued …
3. If the fire burns well but sometimes creates
excessive smoke or burns slowly, it may be caused
by the chimney top being lower than another part
of the house or a nearby tree. The wind blowing
over a house or tree, falls on top of the chimney like
water over a dam, beating down the smoke. The
top of the chimney should be at least three (3) feet
above the roof and be at least two (2) feet higher
than any point of the roof within ten (10) feet.
NOTE: A DRAFT READING OF 0.05 TO 0.06
W.C. (WATER COLUMN) IS SUGGESTED FOR
PROPER BURNING OF THIS STOVE.
GLASS CARE
The following usage and safety tips should be
observed:
1. Inspect the glass regularly for cracks and
breaks. If you detect a crack or break, extin-
guish the fire immediately and contact the
manufacturer for a replacement.
2. Do not slam the door or otherwise impact the
glass. When closing doors, make sure that logs
or other objects do not protrude to impact the
glass.
3. Do not build fires against (or that might fall
against) the glass.
4. Do not clean the glass with materials that
may scratch (or otherwise damage) the glass.
Scratches on the glass can develop into cracks
or breaks during operation.
5. Never attempt to clean the glass while the unit
is hot. If deposits are not very heavy, normal
glass cleaners are adequate using a soft, non-
abrasive cleaning pad. Heavier deposits may
be removed with oven cleaners.
6. Never put substances which can ignite explo-
sively in the unit. Even small explosions in
confined areas can blow out the glass.
Gasket and Glass cleaning products are avail-
able at local retail home centers. Manufacturers of
cleaning products for wood stoves include, A.W.
Perkins Co. (www.awperkins.com) or Rutland
Products (www.rutland.com).
GLASS REPLACEMENT
CAUTION: REPLACE GLASS ONLY WITH 5MM
HIGHTEMPERATURE CERAMIC GLASS OFTHE
PROPER SIZE. DO NOT USETEMPERED GLASS
OR DOUBLE THICKNESS WINDOW GLASS!
Glass Replacement Procedure:
1. Ensure appliance is not in operation and is
thoroughly cooled.
2. Remove screw and glass clip. (See parts list
and diagram.)
3. Lift glass out from glass clip.
4. Remove old gasket and clean glass.
5. Replace new gasket starting at the bottom of
glass working along edges, being sure to center
gasket channel on glass.
6. Trim to length and butt ends together.
7. Replace glass into door, being sure not to over-
tighten screw and clip.
After extensive use, the gasket material which
provides glass and door seal may lose it’s resil-
iency and will need to be replaced. Inspect glass
and door gaskets periodically to ensure proper
seal; if gaskets become frayed or worn, replace
immediately.
Door Gasket Replacement Procedure:
1. Ensure appliance is not in operation and is
thoroughly cooled.
2. Remove old door gasket and clean channel.
3. Using an approved, high temperature gasket ce-
ment, apply a thin coat in bottom of channel.
4. Starting at hinge side of door, work 3/8-inch
diameter fiberglass gasket material into channel
around door unit, end butt and trim to length to
ensure no gaps.
5. Close door and allow three to four hours for
cement to set before firing appliance.

Page 14 | VG650ELG MOUNTAINEER™ www.vogelzang.com VGZ-025 | 201110519.0
CHIMNEY MAINTENANCE
CREOSOTE – Formation and Removal
When wood is burned slowly, it produces tar
and other organic vapors which combine with
expelled moisture to form creosote. The creosote
vapors condense in the relatively cool chimney
flue of a slow-burning fire. As a result, creosote
residue accumulates on the flue lining. If ignited,
this creosote creates an extremely hot fire which
may ignite surrounding materials resulting in a
building fire.
The chimney connector and chimney should
be inspected at least twice a month during the
heating season to determine if a creosote buildup
has occurred.
If creosote has accumulated, it should be
removed. Failure to remove creosote may result
in ignition and may cause a house/building fire.
Creosote may be removed using a chimney brush
or other commonly available materials from your
local hardware retailer.
Chimney fires burn very hot. If the unit or
chimney connector should glow red, reduce the
fire by closing the inlet air control and immediately
call the fire department.
CAUTION: A CHIMNEY FIRE MAY CAUSE IGNI-
TION OF WALL STUDS OR RAFTERS WHICH
WERE ASSUMED TO BE A SAFE DISTANCE
FROM THE CHIMNEY. IF A CHIMNEY FIRE
HAS OCCURRED, HAVE YOUR CHIMNEY IN-
SPECTED BY A QUALIFIED EXPERT BEFORE
USING AGAIN.
A fire in the firebox may be smothered by pour-
ing a large quantity of coarse salt, baking soda, or
cool ashes on top of the fire.
WIRING DIAGRAM - VG650ELG MOUNTAINEER STOVE
When ordering missing or replacement parts, always give the Model Number of the stove,
Part Number, and Part Description. Use the illustrations and part lists provided to identify parts.

VGZ-025 | 201110519.0 Vogelzang International Corp. VG650ELG MOUNTAINEER™ | Page 15
ORDERING PARTS - VG650ELG MOUNTAINEER STOVE
     
17 Pedestal Front............................................... 1
18 Pedestal Base............................................... 1
19 Hardware Pack (not shown) ......................... 1
20 Fire Brick Pack (only one brick shown)......... 1
A Size: 9”x4.5”x1.25” ................................... 17
Half Size: 4.5”x4.5”x1.25” ............................. 2
21 Blower Housing (only) .................................. 1
22 Blower/Motor (not shown)............................. 1
23 Power Cord (not shown) ............................... 1
24 Cord Strain Relief (not shown) ..................... 1
25 Speed Control (not shown)........................... 1
26 Ceramic Fiber Gasket (not shown)............... 1
27 Glass Retainer Screws (shown on pg 15) ... 11
28 Complete Door Assembly (less handle) ....... 1
29 Baffle ............................................................ 1
1 Stove Body ................................................... 1
2 Heat Shield ................................................... 1
3 Blower Assembly F-6.................................... 1
4 Flue Collar .................................................... 1
5 Flue Damper................................................. 1
6 Cover, Ash Cleanout..................................... 1
7 Stove Door Frame ........................................ 1
8 Door Handle Assembly................................. 1
9 Gasket, 3/8” dia. Fiberglass Glass Door ....... 1
10 Glass, Hi-Temp Ceramic .............................. 1
11 Glass Retainer Brackets (shown on pg 15) . 11
12 Door Pins...................................................... 2
13 Ash Drawer................................................... 1
14 Pedestal Top ................................................. 1
15 Pedestal Side................................................ 2
16 Pedestal Drawer Slide .................................. 1
When ordering missing or replacement parts, always give the Model Number of the stove,
Part Number, and Part Description. Use the illustrations and part lists provided to identify parts.

Page 16 | VG650ELG MOUNTAINEER™ www.vogelzang.com VGZ-025 | 201110519.0
ORDERING PARTS - VG650ELG MOUNTAINEER STOVE
  
7 Door Frame................................................... 1
9 3/8” dia. Fiberglass Glass Gasket................. 1
10 High-Temp Ceramic Glass............................ 1
11 Glass Retainer............................................. 11
27 Retainer Screws .......................................... 11
28 Complete Door Assembly (less handle) ....... 1
Glass replacement instructions for model VG650ELG
CAUTION: WHEN REMOVING BROKEN
GLASS, WEAR THICK GLOVES AND SAFETY
GLASSES. KEEP CHILDREN AWAY AND
DISCARD BROKEN GLASS SAFELY.
1. Be sure stove has cooled before beginning.
2. Using a screwdriver, remove all screws (#27)
and retainers (#11) holding glass.
3. Remove glass (#10). Replace with high-
temperature ceramic glass only.
4. Reinstall glass, gasket and retainers. When
replacing broken glass, remove gasket (#9)
from broken glass, remove all glass pieces and
replace around new glass. If gasket is damaged,
it MUST be replaced.
WARNING: Do not use substitute materials.
Replace only with original manufacturer
components.
WARNING: Do not slam door or strike glass.
Slamming door or striking glass may cause
glass breakage.
WARNING: Do not use abrasive cleaners on
glass surface. Abrasives can damage the glass
and breakage may occur when heated.
CAUTION: Do not build fire directly against
glass.
CAUTION: Do not operate stove with
broken glass.
When ordering missing or replacement parts, always give the Model Number of the stove, Part
Number, and Part Description. Use the illustrations and part lists provided to identify parts.

VGZ-025 | 201110519.0 Vogelzang International Corp. VG650ELG MOUNTAINEER™ | Page 17
FLOOR PROTECTOR MATERIAL CALCULATIONS
This stove has been tested for and must be installed on a floor protector with the proper Thermal
Resistance or R-value as stated in the installation instructions on page 3, “Locating Stove” step 1, of
this manual. If the floor protector materials listed in the instructions are not available, materials with
an equivalent R-value may be substituted.
Alternate materials may be rated with C-factor (Thermal Conductance) or k-factor (Thermal
Conductivity) ratings which must be converted to R-value to determine if the alternate material meets
the tested requirements. The following instructions provide the proper information and formulas for
conversion to R-value.
To determine if alternate materials are acceptable follow this sequence.
1. Convert material specifications to R-value:
a. R-value given — no conversion necessary
b. k-factor is given with a required thickness (T) in inches:
R = 1/k x T
c. C-factor is given: R = 1/C
2. Determine the R-value of proposed alternate floor protector:
a. Use formulas in step 1 above to calculate R-value of proposed material(s).
b. For multiple layers, add R-values of each layer to determine overall R-value.
3. If the overall R-value of the floor protector system is equal to or greater than the floor protector
specifications given, the alternate is acceptable.
Definitions:
Thermal conductance(C) = BTU =W
(hr)(ft2)(°F) (m2)(°K)
Thermal conductivity (k) = (Btu)(inch) =W =Btu
(hr)(ft2)(°F) (m)(°K) (hr)(ft)(°F)
Thermal resistance (R) = (ft2)(hr)(°F) =(m2)(°K)
Btu W
Example:
The specs of floor protector material should be 3/4-inch thick material with a k-factor of 0.84.
The proposed alternative material is 4” brick with a C-factor of 1.25 over 1/8-inch mineral board
with a k-factor of 0.29.
Step 1: Convert specs to R-value.
R = 1/k x T = 1/0.84 x 0.75 = 0.893 System must have a R-value of 0.893 = Rspecs
Step 2: Calculate R-value of individual components
4” Brick with C-factor = 1.25. R = 1/C = 1/1.25 = 0.80 = Rbrick
1/8-inch (0.125”) mineral board with k-factor = 0.29. R = 1/0.29 x 0.125 = 0.431 = Rmin.brd.
Step 3: Add R-values of components to get total R-value of system
Rbrick + Rmin.brd = 0.80 + 0.431 = 1.231 = Rsystem
Step 4: Compare Rsystem to Rspecs
Rsystem = 1.231 is larger than Rspecs of 0.893. System R-value exceeds the required
specifications and therefore is an acceptable alternative.

Page 18 | VG650ELG MOUNTAINEER™ www.vogelzang.com VGZ-025 | 201110519.0
A. Brick Masonry
Minimum 3.5˝/89mm thick brick masonry all framed into com-
bustible wall with a minimum of 12˝/305mm brick separation
from clay liner to combustibles. The fireclay liner shall run
from outer surface of brick wall to, but not beyond, the inner
surface of chimney flue liner and shall be firmly cemented in
place.
B. Insulated Sleeve
Solid-insulated, listed factory-built chimney length of
the same inside diameter as the chimney connector and
having 1˝/25.4cm or more of insulation with a minimum
9˝/229mm air space between the outer wall of the chimney
length and combustibles.
C. Ventilated Thimble
Sheet steel chimney connector, minimum 24 gauge in
thickness, with a ventilated thimble, minimum 24 gauge
in thickness, having two 1˝/25.4mm air channels, sepa-
rated from combustibles by a minimum of 6˝/152mm of glass
fiber insulation. Opening shall be covered, and thimble
supported with a sheet steel support, minimum 24 gauge in
thickness.
D. Chimney Section Pass-through
Solid insulated, listed factory-built chimney length with an
inside diameter 2˝/51mm larger than the chimney connec-
tor and having 1˝/25.4mm or more of insulation, serving as
a pass-through for a single wall sheet steel chimney con-
nector of minimum 24 gauge thickness, with a minimum
2˝/51mm air space between the outer wall of chimney
section and combustibles. Minimum length of chimney
section shall be 12˝/305mm chimney section spaced
1˝/25.4mm away from connector using sheet steel sup-
port plates on both ends of chimney section. Opening
shall be covered, and chimney section supported on both
sides with sheet steel support securely fastened to wall
surfaces of minimum 24 gauge thickness. Fasteners
used to secure chimney section shall not penetrate
chimney flue liner.
CHIMNEY CONNECTOR SYSTEMS & CLEARANCES

VGZ-025 | 201110519.0 Vogelzang International Corp. VG650ELG MOUNTAINEER™ | Page 19

Page 20 | VG650ELG MOUNTAINEER™ www.vogelzang.com VGZ-025 | 201110519.0
Vogelzang International Corporation
400 West 17th Street
Holland, Michigan 49423
www.vogelzang.com
Phone: [phone]
Fax: [phone]
COMPANY TESTIMONY:
“FOR GOD SO LOVED THE WORLD THAT HE GAVE HIS ONLY BEGOTTEN SON, THAT WHOEVER

JOHN 3:16
MADE IN CHINA
This Vogelzang heating appliance is safe when installed properly and will provide you with years of
service. However, always exercise good judgement when you are using this stove.You are dealing with
FIRE! Fire is inherently dangerous and must be treated with respect. Stay warm and in good health!
Respectfully yours,
SteveVogelzang
Proprietor
DO NOT USE THIS STOVE IN A
MOBILE HOME, MANUFACTURED HOME,
TRAILER OR TENT — NO EXCEPTIONS!