Vogue 330410 Wiring diagram

To prevent the risk of accidents or damage to the appliance, it is essential
to read these instructions before it is installed and used for the first time
3304
INSTALLATION
INSTRUCTIONS
USER GUIDE
VOGUE Intelligent Rangehood - Steam Wash 900mm
10

Contents
The installation guide
Installation instructions
Electrical schematic diagram
Clean and maintain
Important information
Safety warning
Product structure schematic
The attachment list
Outline dimensions
Control panel and function comments
Precautions
Daily maintenance
Product parameters
2
2
3
3
4
4
5
6
8
9
11
12
12
2 3
4567
8 9 10 11
12

Important information
Safety warning
All packaging materials are environment-friendly and recyclable. Please dispose these
packaging materials in an environmentally friendly manner so as to maintain a good
environment.
Please do not allow children to play with plastic film and packing boxes, which may cause
asphyxiation. Please keep the children away from the packaging materials. The packaging
materials are not children's toys.
When the old smoking machine can no longer be used, it should be abandoned. Remove
power cord plug and cut power cord.
The old cooker hood contains reusable useful materials.Please assist in the proper handling
or recycling of environmental protection.
This product is for household use only. Please do not use it in special environment (e.g.
outdoor);It must not be used to discharge hazardous or explosive materials or gases;
The gas emitted from the cooker hood should not be discharged into the hot flue gas used to
discharge the smoke from burning gas or other fuels.
In order to ensure that you can use the smoke absorber correctly and safely, please read the
instruction manual of the cooker you purchased at the same time.
Please contact the local distributor or company's customer service department immediately if
there is any obvious damage to the oil absorption machine.
Only through professional training, and have qualified personnel, to installation and
debugging and maintenance of the oil absorption, other staff without permission, shall not be
carried out on the oil absorption without installation or dismantling machine maintenance, so
as to avoid serious consequences.
Please read this manual carefully before installation, and strictly follow this instruction to
properly install and use. We are not responsible for any damage caused by improper
installation or use.
Prohibit the fire to directly bake the cooker hood.
The room must be well ventilated when using a cooker hood in a well-sealed building.
If it is not cleaned according to the instruction manual, there is a risk of fire.
It is forbidden to modify this product, and the power cord shall not be replaced or modified by
itself.
If the power cord is damaged, it must be replaced by the manufacturer, its maintenance
department or similar professional staff in order to avoid danger.
1.
2.
3.
4.
5.
●
●
●
●
●
●
●
●
●
●
2 3
4567
8 9 10 11
12

Exhaust pipe
Exhaust pipe fixed ring
Check valve
Check valve sealing gasket
Installatinon plate
Decorative cover plate
Cold plate
Oil cup
4
1
56
78
11
9
10 12
14 15
13
4
1
5
6
7
8
Ref. Qty. Product Components
Water cup
Filter cotton
Screws(ST4.2×16)
Screws (M5×16)
Screws(ST4.2×9.5)
Plastic expansion pipe
Note: filter cotton in water cup.
Cross - groove countersunk
head wood screw.（M5×50）
12
9
10
11
13
14
15
Ref. Qty. Product Components
1
1
1
1
1
1
1
1
5
4
1
2
6
6
1
Product structure schematic
The attachment list
Adjustable Decorative cover
Decorative cover
Switch panel
Guide plate
lighting
Cold plate
Oil cup
Water inlet
2 3
4567
8 9 10 11
12

Outline dimensions
Control panel and function comments
See page 8 specification for long and wide dimensions
It can be used after power supply
Light
Time
Time+power
Boost
Speed
Power
Steam
washing
Short press:Turn on the light ; Long press:Adjust the light.
Open/close clock show
Short press time: Hour key flashing, Short press speed: adjust hour;
Short press time : minute key flashing, Short press speed:adjust minute;
Short press time:confirm save.
Long press:Start;
Long press and twice short press:Cancel the indicator light reminder.
Long press:Start;
Long press and twice short press:Cancel the indicator light reminder.
Short press:Adjust speed(As clock flash,adjust clock).
1st Short press:Startup(3 speed); 2nd Short press:Delay 3 min;
3rd Short press:OFF immediately.
long
high
wide
Short press:0.5 second Long press:2~3 seconds
403mm
0~310mm
313mm
2 3
4 5 6 7
8 9 10 11
12

Precautions
Daily maintenance
Surface cleaning
When the indicator light is on for 3 hours, the indicator light will be lit.
After the indicator light is lit, the steam washing icon will flash 10 times
next time, reminding the user to clean the cigarette machine.
display
gear display ( gear )
, , ,
time delay display
Steam washing clean
air dry（minute）
clock display
3-2-1（minute）
（clock）
Please note that the power supply voltage and frequency should be consistent with the
voltage and frequency required by the product.。
Please make sure that the oil cup has been properly installed.。
In the cooking process, please keep the kitchen environment well ventilated or open the
cigarette smoking function.
In the process of use, if abnormal conditions (abnormal noise, odor, smoke, fever), the power
should be shut off immediately, unplug the plug.
Do not plug the power cord with wet hand.
Do not pull the power cord to pull out the power cord plug.
If you do not use the cooker hood for a long time, please unplug the power cord.
When the cooker hood is working, it is forbidden to put the hand into the fan operation area.
Always clean the surface and screen of the cooker hood. Do not use clean ball, brush or
coarse cloth to avoid scratching the surface of the machine.
When the oil cup window can be seen in the oil, please timely
dump, otherwise it may spill out of the stove.
Cleaning screen method: according to the removal guide of the condenser plate and the filter
screen (see page 7), remove the condensation plate and filter screen, and put the filter net into
the warm water with neutral detergent, and then use the soft brush to clean it.
1.
2.
3.
●
●
●
●
●
●
●
●
Oil cup window
2 3
45 6 7
8 9 10 11
12

Daily maintenance
Steam washing (machine internal cleaning)
Water cup is filled
with pure water to
live distilled water.
Long press the steam washing
button to start the steam
washing for 3 seconds.
2 3
4 5
6 7
1
2
3
remove oil cup
Pour out the product oil
Put back into the oil cup
1
2
3
Remove oil cup
Pour out the product water
Put back into the oil cup
Insert the water cup
aqueduct into the inlet.
1 Indicator light flashing
The instructions require
steam washing.
12 minutes steam washing
and 3 minutes air drying
inlet
During steam washing, do not touch the surface
CAUTION of glass panels or deflector to avoid scalding.
1. Cancel the steam washsing reminder (not washing):
Long press 3 seconds + short press twice to fast forward to the end.
2.
Short press
Fast forward or end in advance（during washing）:
again to fast forward to the next step.
2 3
4 5 6 7
8 9 10 11
12
washing drying

Internal clean
Cleaning impeller and volute should be completed by professionals.
Clean the impeller and volute inside
and outside with a soft brush with
neutral detergent, and then install it
in reverse order.
First, unplug the power plug, remove
the machine and place it in a reliable
position, remove the decorative cover
and set screw.
screw
Remove the decorative cover
Remove the screws on the frame
cover and remove the frame cover.
Remove the screw from the volute and
the nozzle, and remove the inlet wind ring.
Inlet wind ring
Nozzle
Turn the lock nut and remove
the impeller in the direction of
the motor shaft.
Impeller
Impeller
lock nut
1 2
34
5 6
2 3
4567
8 9 10 11
12

Guide for disassembly of condensates and filters
Remove the condenser plate to indicate
2. After the condenser is opened, hold
the condenser with both hands and
remove it horizontally.
1. Hold the condenser with both hands,
and press the left and right sides to
open the condenser.
2. After the filter is opened, both hands
shall be taken out of the filter screen
along the horizontal direction.
1. Hold the mesh by hand, use the cross
screwdriver to top the filter to the left and
right sides of the filter, open the screen.
Remove the filter screen to indicate
Product parameters
2 3
4 5 6 7
8 9 10 11
12
Voltage Noisea
The level of energy
efficiency
Total pressure
efficiency (%)
Turn off the power (W)
Standby power (W)
Odor reduction (%)
Oil separation (%)
Net weight (kg)
Size (mm)
Length × width × height
The fan number
Motor power (W)
Maximum lighting
power (W)
Rated power (W)
Diameter of air
tube (mm)
Air flow
φ190
1600
12V=/1.5W×2
260
Single
220-240V/50Hz
≤2.0
≥96
≥85
N/A
≥23
Level 1
280
380
29Wind pressure (Pa)
Maximum static
pressure (Pa) 896x534x692
≤
55
69dB(A)
/
(SPL/APL)
Acounstc Power Level
*Sound Power Level/
19m³ /min
(Boost:
2
m³ /min)
1

The installation guide
To determine the location (unit: mm)
1
The range hood machine should be installed horizontally and above the cooker.
The installation diagram is as follows:
The installation (unit: mm)
2
Installation precautions
Exhaust pipe to the cabinet
installation diagram
Schematic diagram of opening size
of exhaust pipe at the ceiling
120
69
200
905~915
650~750 692~929800~850
403
313
The center line of range hood machine
As shown in the picture on the right in the
out of the wall of 4 to 8 mm diameter, depth
of 50 ~ 60 mm hole, plastic expansion pipe
pressure inside the manhole, provided with
M5 * 50 countersunk head wood screws to
fix the body panels and reliable.
20~40
538
692~929
Upholstery board
Installation plate
310
324
180
Noise: for the sound power level of A, the average sound pressure level noise is 55dB (A).
Wind volume, maximum static pressure: the measured value and the express value should
not exceed the value of -10%.
Net weight: refers to the machine's own weight plus the installation and use of light
accessories, including hanging board, check valve, exhaust pipe, screw, etc.
Stir-fried function: when running function for a while, air volume for 20 m3/ min.
After installation of the cooker hood, the left and right level should be maintained.
Should avoid excessive Windows and air convection in the vicinity of the cooker hood,
otherwise it will affect the efficiency of the cooker hood.
Exhaust pipe requirements.
The exit of the exhaust pipe should not be too long.
●
●
●
●
●
●
●
●
2 3
4567
8910 11
12

Install check valve
3
Install the machine
4
The install exhaust pipe
5
Install adjustable decorative cover
6
Install the check valve components together with the check
valve seal pad in the position of the rack outlet, tighten with
4 ST4.2 x 16 screws at random, check and make sure that
the disc is rotating flexibly.
Align the hole in the rear of the body to the hanger of the
body plate, and hang it from the top down; After hanging
the cooker hood, confirm the installation level of the
machine, and then use the randomly equipped M5 x 16
self-tapping lock screw to load the screw hole in the top of
the body plate to prevent the machine from falling off
accidentally.
Will exhaust pipe fixed ring on the exhaust pipe compo-
nent, one end of the exhaust pipe components installed
with loaded check valve outlet, then exhaust pipe fixed ring
threaded on the check valve, pressure exhaust pipe joint.
At the end of the exhaust pipe, the other end of the pipe is
directed to the indoor or public flue. If the exhaust pipe
does not match with the public exhaust pipe, it can be
converted to the after-sales department to purchase the
pipe reducer. If the pipe is too long, please adjust the long
pipe to the contraction state and fix it with adhesive tape to
prevent the pipe from swinging during the working process.
According to the installation height, adjustable decoration
to cover the required in the out of the wall two phi 8 mm
diameter, depth of 50 mm hole, the expansion pipe
pressure inside the manhole, provided with two M5 x50
cross slots countersunk head wood screw will cover
decoration hangs Taiwan reliable fixation. Adjustable
decorative cover to the corresponding height, and use the
2 ST4.2 x 9.5 cross flat head self-tapping screw with
random equipment on the wall.
The check valve
Hang hole
The body panels
Check valve gasket
Exhaust pipe
component
Fixed ring
Decoration
cover plate
Adjustable
decoration
cover
Exhaust pipe joint
Check valve outlet
2 3
4567
8 9 10 11
12

Daily maintenance
Install check valve
7
Install cold plate
8
This range hood machine is an external exhaust type cooker hood machine, and the gas
discharged from the cooker hood machine should not be discharged into the hot flue gas
used for the discharge of smoke burning gas or other fuel.
If the range hood is installed above the gas stove, the distance from the bottom of the body
to the focal plane is at least 650mm, which should be considered if the installation instruc-
tions of gas-fired stoves provide a larger installation distance.
It is strictly forbidden to modify the product without authorization, and the power cord shall
not be replaced or modified by itself.
Please do not install the cooker hood machine on the wall of flammable material.
Do not install the cooker hood machine on the top of the stove with solid fuel.
When drilling holes in the wall, avoid electrical wires embedded in the wall to avoid electric
shock hazard.
A special power supply socket shall be used for the cooker hood machine, and the special
power outlet should be reliably grounded (the product must use 10A, 220~v or above).
The wall shall have sufficient supporting strength for the installation of the cooker hood
machine The hollow core of the hollow wall shall be greater than 30mm, and the concrete
wall can be directly punched and installed. The machine must be securely mounted on the
wall.
The cooker hood machine may have very sharp edges. Please wear protective gloves when
you install or clean the cooker hood machine.
If your kitchen is under a state of decoration, do not use cooker hood exposed, for building
materials, dust, paint, coatings and their volatile gas cooker hood surface causes corrosion
and lose luster, please install cooker hood in after the decoration.
Hold the bottom end of the oil cup with both hands
and place the oil cup horizontally. Insert the oil cup
into the holder of the oil cup holder and push the oil
cup back to the county seat.
The hands hold the cold plate, cold
plate rotation of a shaft insertion on
the guide plate hook slot, turn up,
insert the condensation plate card
buckle on the guide plate in the
booth, fixed can.
Booth
Oil cup stents
Pins
Oil cup
Condensing
boards buckle
Guide plate
Hook
Hook slot
Rotating seat rotating shaft
Rotator
Cold plate
●
●
●
●
●
●
●
●
●
●
2 3
4567
8 9 10 11
12

Before cleaning, please note that when you need to clean the condenser and screen, cut off the
power and unplug the power.
It is recommended to maintain and maintain the washing machine regularly. It is recommended
to use dry cloth after cooking or to occupy the inner and outer surface of the wet cloth cleaning
machine with neutral detergent. Do not use gasoline, acid, benzene, this solvent or any other
chemical to clean the cooker hood.
When the oil cup in the oil cup is filled with oil cup clean
line, please clean the oil cup in time. The oil cup
disassembly is as follows: hold the lower part of the oil
cup with both hands, and remove the oil cup horizontally;
After cleaning, install the oil cup in reverse order.(the oil
cup is longer, please keep the level when the oil cup is
removed so as not to overflow the oil.)
Regularly replace the filter cotton.
The attachment is equipped with 5 filter cotton for
replacement. In order to ensure better steam cleaning
effect, a replacement can be made every two years.
Replace the filter cotton: open an Angle according to the
direction on the lid of the water cup, then take out the
water cup cover along the vertical direction. Remove the
filter cotton at the filter junction.
When the lighting is needed (by professionals), please remove the power plug first.
Insert a small screwdriver into the gap between the lamp and the guide plate and gently pry
open and remove the lamp.
Replace the new lamps with the same specifications and install them in the mounting holes of
the guide plate.
Electrical schematic diagram
Clean and maintain
POWER BOARD
Light
(Black)
(Black)
(White)(Yellow)
(Brown)
(Orange)
(Red)
(Blue)
(Red)
L
N
E
Temperature Sensor
Steam generator
Water cup cover
Filter junction
Filter cotton
Tump
Heat protector
Heat protector
220V-240V~/50Hz
●
●
●
●
2 3
4567
8 9 10 11
12

2 3
4 5 6 7
8 9 10 11
12 P/N:16173000A10872