-4- -5- -6-
6400-000123
6. Cabling RJ45
Connect Ethernet/RJ45 cable into Ethernet port of media
converter and other end to attached networking device.
• Copper of the media converter supports Fast Ethernet
as well as Gigabit Ethernet (10/100/1000Base-T RJ45
Port)
• The RJ45 port on the media converter supports auto
negotiation and auto MDI/MDI-X to eliminate the need
for crossover cabling.
Note: Category 5e cable or above should be used.
7. Link Fault Signaling (LFS)
The LFS LED will immediately light to indicate when a
cable has been severed or when some other cause of
disruption in service has occurred. The LFS function
monitors both copper and ber segment giving a total
connection status report.
DIP Switch 1: Set LFS to ON for normal operational use;
OFF when installing cables or when
testing the network connection.
7. Loop back Test
8. LED Indicators
This Converter features DIP switches to activate both
local and remote loopback diagnostic test functions. Use
local loop back (LLB) to check if the copper segment is
connected properly, and use remote loop back (RLB) to
check if the ber segment is connected properly.
Note: When enabling loopback testing in one side, another’s
trac will be blocked until the loopback is disabled.
Limited Warranty
VOLKTEK Corporation warrants this product against defect in materials
and workmanship for a period of TWO (2) YEARS to the original
purchaser.
If you discover a defect, VOLKTEK will, at its sole option, repair or
replace the product at no additional charge, provided that you contact
VOLKTEK technical support to obtain a Return Merchandise Authoriza-
tion Number (RMA) and instruction on how and where repairs can be
made. This warranty does not apply if the product has been damaged
by accident, abuse, misuse, misapplication, neglect, re, water,
lightning or other acts of nature, failure to follow supplied instructions,
installation or removal, have been repaired or have undergone
attempted repair by unauthorized personnel without written consent
from VOLKTEK, modied, defaced, or has its serial numbers removed.
VOLKTEK reserves the right to use remanufactured, refurbished, or
used parts and components in making warranty repairs.
All expressed or implied warranties for this product, including the
implied warranties of merchantability and tness for a particular
purpose are limited in duration to the warranty period. No warranties
expressed or implied will applied after this period. VOLKTEK shall not
be liable for lost prots, damage to other property caused by any
defects of this product, or damages based upon inconvenience, loss of
product use, loss of time, commercial use, incidental and/or
consequential damages for the breach of any expressed or implied
warranty, including damages to property, and to the extent permitted
by law, damages for personal injury, even if VOLKTEK has been advised
of the responsibilities of such damages.
If you have any further questions, please contact Customer Support:
Address of the manufacturer.
VOLKTEK CORPORATION
4F, 192 Liancheng Rd, Zhonghe, New Taipei 23553, Taiwan
Tel: +886-2-8242-1000
Fax: +886-2-8242-3333
Straight direction installation
Moun�ng direc�on
with screw
Horizontal direction installation
Moun�ng direc�on
with screw
RJ45
Fiber
LLB
RLB
Illuminated
O
PWR
(Green)
Power On by 12VDC power input
Power fails or is not available
Illuminated
O
ALM
(Red)
LFS enabled and link fault happened
LFS disable or no link fault happened
LNK/ACT
RJ45
1000 Illuminated
O
links speed at 1000Mbps
Link speed at 10/100Mbps or link failed
Illuminated
Blinking
O
Copper port link-up
Data is transmitting / receiving
Link failed
LNK/ACT
Fiber
1000 Illuminated
O
links speed at 1000Mbps
Link speed at 100Mbps or link failed
Illuminated
Blinking
O
Fiber port link-up
Data is transmitting / receiving
Link failed
Operating Temperature
0˚C~50˚C
Storage Temperature
-20˚C~70˚C
Altitude
Up to 2000m
Ambient relative humidity
10 to 95% (non-condensing)
9. Environmental limits
!ATTENTION:
This device complies with Part 15 of the FCC rules.
Operation is subject to the following conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received
including interference that may cause undesired operation.
!ATTENTION:
If the equipment is used in a manner not specied by the
VOLKTEK, the protection provided by the equipment may
be impaired.
