Volt Polska 6pro122420 User manual

20A BATTERY CHARGER WITH LCD DISPLAY
LCD Display
SELECT LCD Display Status
MODE MODE1
MODE MODE2
MODE MODE3
MODE MODE4
Charging in Normal temperature
Charging in Low temperation
Charging in Silent mode
Charging in Low temperation
and Silent mode
6-step fully automatic charging cycle
Charging 12V
Charging 24V
Risk of chemical burns!
The charger features the following safety features to prevent damage to the charger and
▪Short circuit (defective battery),
▪incorrect connection (connected with reversed polarity),
▪overheating
▪excess current
▪overcharging
Risk of injury!
▪Never attempt to charge non-rechargeable, damaged or frozen batteries.
▪Do not use this device to charge dry cell batteries. These could burst, resulting in personal
injury and
property damage.
▪Please read and follow the operating manual and all safety instructions for the batteries to
be charged and the vehicle before using this device.
Risk of damage!
▪Never place the device over or near the battery to be charged. Gassesfrom the battery
battery as the connecting cable
▪Never operate the device if it has been dropped or damaged in any other way.For
Safety functions
▪Gaseous hydrogen (detonating gas) may form when charging the battery. Contact with
open fire (flame, embers, sparks) may result in explosions.
▪Never charge the battery close to an open fire or in places where sparks may occur.
▪Always ensure sufficient ventilation.
▪Be sure the supply voltage matches the input voltage specified on the device (220-240 V-
AC) to prevent damage to the device.
▪Only connect and disconnect the battery connecting cables when the charger is
disconnected from the mains.
▪Do not cover the device while charging, as it may be damaged from extreme heating.
Immediately stop using the device if you notice smoke or an unusual odour.
▪Do not use the device in rooms where explosive or flammable substances are stored (e.g.
petrol or solvents).
Risk of electrical shock!
▪Chargers may interfere with the operation of active electronic implants,e.g. pacemakers,
hus pose a personal hazard.
▪Avoid pouring or dripping water or other liquids over it. If water penetrates electrical
devices, the risk of electric shock increases.
▪Ensure that all plugs and cables are free of moisture. Never connect the device to the
mains with wet or moist hands.
▪Never touch both connections at once when the device is in uses.
▪Unplug from mains before connecting or disconnecting the charging cable with the battery,
or when the device is no longer being used.
▪Remove all device cables from the battery before attempting to drive your vehicle.
▪Always unplug device by the plug. The cable may be damaged.
▪Do not use device if damaged. Damage to the power cable, the device or the charging
cable increase the risk of electrical shock.
▪Do not attempt to disassemble or repair the device. Immediately have a defective device
or damaged
power cable repaired or replaced by a speciality shop.
▪Risk of short circuits! Do not allow the two connectors from the charging cable to touch if
the power plug is plugged into the power outlet. Be sure not to connect the connectors or
conductive objects (e.g. tools).
▪Never use the cable to carry or pull the device.
WARNING!
Explosion and fire hazard!
▪Batteries contain acid, which could damage the eyes and skin.Charging batteries further
generates
gasses and vapours hazardous to the health.
▪Use safety goggles and acid-proof safety gloves. Protect clothing, e.g.with an apron.
▪Never tip the battery, as acid may leak.
▪Always ensure adequate ventilation.
▪Do not inhale emerging gasses and vapours.
▪Avoid any contact with caustic battery acid. Immediately thoroughly flush skin and any
objaects which have come into contact with acid. If eyes have come into contact with
at least 5 minutes. Contact your physician.
cid, flush eyes with running water
the battery poles through
could damage the unit. Place the device as far from the
battery
will allow.
inspection and repair, take it to a qualified electrician.
the battery or the vehicle:
OPERATION
Before use
Before connecting the charger, the operating instructions must be observed.
Furthermore, the instructions of the
connected car battery must be observed. Secure the car, switch off
the ignition.Clean
Ensure sufficient ventilation.
Connecting
Connect the "+" pole clamp (red) of the charger to the "+" pole of the battery
Connect the "-" pole clamp (Black) of the charger to the "-" pole of the battery
Connect the mains cable with AC 230V VDE plug of the charger to the main socket
The battery voltage display shows the current battery voltage after connecting.
If the connecting is" Reverse" or "Short Circuit" , Voltage display "88.8v" will be display
"Err"
The battery charger can automatic recognition 12V or 24V voltage after connecting.
LCD display can automatic show the percent of voltage.
Before start charging , please press the Button of to Select which MODE you
want.
Then press the button of . The charger start to work.
If you want to stop charging , please press the Button of ,The charger will be
stop.
START
STOP
START
STOP
MODE
Disconnect
Disconnect the appliance from mains supply.
Remove the “-” pole clamp (black) from the “-” pole of the battery.
Remove the “+” pole clamp (red) from the “+” pole of the battery.
the battery poles. Take care that while doing so, your eyes do not come into contact
with the dirt.
vehicle manufacturer regarding a permanently
Technical Data
Input Voltage 220 – 240 VAC ~ 50/60 Hz
Output Voltage 12V DC or 24V DC
Efficiency >85%
Charging Voltage 14.3V DC ± 0.3V DC or 28.6V DC
± 0.3V DC
Charging Current 20A for 12V DC or 10A for 24V
DC
Surrounding temperature -10 Celsius to 40 Celsius
Battery type Lead-Acid e.g. AGM
Generated noise < 50 db (tested from distance of
50 cm)
Dimensions 292 x 118 x 60 mm
Weight 1,5 kg

X-ON Electronics
Largest Supplier of Electrical and Electronic Components
Click to view similar products for Adapters category:
Click to view products by VOLT POLSKA manufacturer:
Other Similar products are found below :
PD45II POLOLU MICROSD ADAPTER GROVE CAPE FOR BEAGLEBONE GROVE BREAKOUT FOR LINKIT SMART 7688 DUO
RBFN-EU-SEN-BMT-12 11293 9127 9546 9755 9983 OKY1201 OKY1204 I2C HUB DUAL MAX14870 MOTOR DRIVER SHIELD
6PRMOBI06S 6PRO122420 AB-12.100/ST8VA BC-20 PRO 20A 12V BC4 BQ-CC65 CABLE-1/CL CABLE-2/CL CABLE-3/CL
CL12.6VDC-1.5A CL12.6VDC-2.5A CL12.6VDC-4.76A CL8.4VDC-1.2A CL8.4VDC-2.5A CL8.4VDC-5A EP12M248L EPA1020-075
EPA1206PRO GM3A GP 2XP861 + 8X2100 RECYKO DOK GP E411 + 4 X R6 2100 RECYKO GP ECO B421 + 4XAA RECYKO 2100
GP ECO B421 + 4XAA RECYKO 2100 + D451 GP ECO B421 + 4XAA RECYKO 2700 GP ECO E211 + 2XAA RECYKO 2100 GP ECO
M451 + 4XAA RECYKO 2700 GP P461 + 4 X 2100 RECYKO DOK GP PRO P461 + 4XAA RECYKO 2100 LIFEPO4-12.8V-5A LIFEPO4-
38.4-5A LI-ION-11.1V-5A LI-ION-14.8V-10A LI-ION-14.8V-5A LI-ION-14.8V-8A LI-ION-25.9V-2A LI-ION-37V-4A