VOLTRIUM Pro Series User manual

Pro Series
Owner's Manual
2022 Edition
For:
Pro+

Thanks for Choosing Voltrium
We are committed to bring you desirable & environmentally
friendly Micro Transport.
Developed in Melbourne Australia, each vehicle is designed
and tinkered on by a team of talented, passionate engineers
and technicians who's mission is to put a smile on your face.
Because to us it is more than just a scooter.
-The Voltrium Team.

Always wear a helmet & obey all laws!
Important!
Variants of the Rogue series scooters conform to the
Australian Personal Mobility Device (PMD) vehicle category
in some states of Australia.
Please check with your local state & territory's road rules before
riding in public.
To minimise risk, riders should wear safety equipment such as:
Full Face Motorcycle Helmet
Full Face Bicycle Helmet
Cycling Goggles
Cycling Gloves
Elbow pads
Knee Pads
Closed Footwear
The rider assumes ALL risks associated with operating this
scooter.
The recommended rider age is 14+

Do Not Hose down or
pressure wash. Use a
towel with soapy
water to clean.
Do not allow the
battery to fall into a
state of deep
discharge
Do not jump the
scooter.
Do not ride with more
than 1 person
onboard
140KG
Limit
Do not overload the
scooter.
Periodically maintain
the scooter and check
for proper operation
before riding.
Precautions
Use Genuine replacement parts & Accessories. Damage & Improper
performance of the scooter may occur otherwise

Package Contents
1x Pro Series Scooter
1 x Charger
1 x Tool Kit
1 x Spare Fuse
1 x Seat
1 x Seatpost & Clamp
Accessories (Optional)

Assembly
Carefully remove the scooter from the
box
Unfold the scooter by pressing down
on the Folding lever with one hand
while gently pulling up on the steering
column with the other.
Fully Extend the Steering column to the
upright position, until you feel the
mechanism lock into place.
Affix handlebars, by firstly, removing the
top cap of the handle bar clamp.
Once removed, place handlebars onto
the bottom cap.The correct orientation
is with the throttle on the right hand
side.
Ensure the alignment of the handlebar
assembly is true with the front wheels
of the scooter.
Tighten the bolts on the handlebar
assembly clamp.
It is recommended that you use high
quality workshop grade tools to
complete the assembly.
Fasten the Speedometer and bracket
assembly to the underside of the
handlebar clamp with the existing 2x
M6 bolts.

Assembly
Insert the seat stem by passing the
locking feet through the slits of the foot
board and then pushing the stem
forwards to lock it into the battery box.
Secure seat with the knob. Fasten until
handtight.
Place seat onto the seatpost, adjust the
rake and then tighten the two nuts on
the underside of the seat evenly.
Remove the bottom X bar from the
headstem area. Bolt the twin headlight
assembly to the now vacant 4 holes
with the original 4 bolts.
Attach the horn to the same headlight
bracket. Using the top right hand side
nut and bolt to affix the horn.
The rear nut of the horn can be
positioned in the cutout of the frame
for flush fitment as pictured.

Controls Layout
Speedometer
Switch Cluster
Brake Levers
Throttle
HIGH /ECO mode switch
Ignition Key
1.
2.
3.
4.
5.
6.

2-4 Hrs
In extreme temperature conditions, the battery may not charge.
Avoid charging under direct sunlight
Let the scooter cool down for at least 10 minutes after riding before charging.
Ensure cooling fan on charger is operating at all times during charging.
Ensure charge port is dry before inserting charger.
Charging
The charging process takes
between 2 - 4 hours.
When the scooter's battery
meter is flashing on 0 bars,
recharge immediately
The charge port is located on the front right hand side of the battery box.
Insert the Round, three pronged connector into the charge port, then insert the
AC plug into a power socket. Switch power on to charge.
LED1 and LED2 will be red when scooter is charging.
LED2 will turn green and cooling fan will stop once scooter is fully charged.
Ensure the cap is closed when not charging to prevent water ingress.

Do not apply throttle when dismounted.
Starting up the scooter
Turn the ignition key clockwise by 1 "Click
Once the dashboard is switched on, the scooter is ready to go.
1.
2.
It is best practice to switch the scooter off when parked and not in use.
Riding
Pre - Ride Checks
Check Tyre Pressures (50PSI - On Road Tyres, 40PSI - Off Road Tures)
Ensure all bolts and screws are tight
Ensure Chain drive system is properly lubricated, adjusted and clean.
1.
2.
3.
Headlights
Flip the headlight switch on the left cluster to turn on1.
The headlight(s) have 3 modes that can be cycled through by switching the light on and
off:
Mode 1: High Beam - Full Brightness
Mode 2: Low Beam - Half Brightness
Mode 3: Strobe - Flashing
Horn
Press horn button on the left cluster to activate1.
Ride Modes
Limits top speed of scooter to
25km/h (Can be adjusted in P-
settings)
Reduces performance of scooter
Eco Mode
Unrestricted performance.
High Mode
The ride modes are changed by pressing the Red button under the throttle
Button pressed in - Eco Mode
Button not pressed in - High Mode