Von Duprin 35A-F User manual

*911402-00*
911402-00
© Allegion 2016
Printed in U.S.A.
911402-00 Rev. 05/16-d
#10-24
Dogging Key
(use with non-fire devices to lock down pushbar)
Devices covered by these instructions:
33/35A Rim Exit Device
33/35A-F Rim Exit Device
CD33/35A Rim Exit Device
EL33/35A Rim Exit Device
SS33/35A Rim Exit Device
Rim Exit Device Installation Instructions
33/35A Series

2
SCREW CHART
Device Subassembly Screw Application
Z\v-20 x1” (25 mm) Trim mount or sex bolts:
1C\v” (44 mm) door
Z\v-20 x 1-Z\x” (38 mm) 2Z\v” (57 mm) door
#10-24 x 1” (25 mm) Metal door surface mount
(Yellow)
#10 x 1Z\v” (32 mm) Wood screw Wood door surface mount
#10-24 x C\v” (19 mm) Surface mount or Sex bolts
1C\v” (44 mm) door
#10-24 x 1Z\,” (29 mm) Sex bolts, 2Z\v” (57 mm) door
#10-16 x C\,” (10 mm) Thread cutting End cap
#10-12 x 10-24 x 1Z\v” (32 mm)
combination Metal or wood frame
#10-24 x C\v” (19 mm) Metal frame
#10 x 1Z\x” (38 mm) Wood screw Wood frame
G
#10-24 x C\v” (19 mm) Metal frame
#10 x 1Z\x” (38 mm) Wood screw Wood frame
H
#10-12 x 10-24 x 1Z\v” (32 mm)
combination Metal or wood frame
I
#8-18 x C\,” (10 mm) Thread cutting Center case cover

3
1 Draw horizontal device and strike center lines (C
L).
For double doors with a
mullion and strike already
installed, use existing
strike center line.
RHR LHR
RHR
*39ZC\zn” (101.1 cm)
from finished floor
*
2 Prepare frame for strike using paper templates.
 See pages 8 through 12 for strike templates and frame
preparation dimensions.
1439 strike
preparation
shown
Metal #25 #10-24
OR
Wood
Z\,” (3 mm) x 1” (25 mm) deep
 See “Screw Chart” on previous page for screw types and
sizes.
3 Install strike using two screws only at this time.
1439 Strike (standard)
Panic Device
Fire Rated Device
299 Strike
299F Strike
Install strike
1/16” past door
side of stop
E
F
1606 Strike
Mullion
Door
H
Door
G
 For 499F strike installation, see page 6.
499F Strike

4
4 If using a 1439 strike, install wear strip. If not, go to
step 5.
A. Center wear strip on strike as shown.
B. Mark and drill 1/8” dia. holes (4 places).
C. Install wear strip with flat head drive
rivets (4 places) from 1439 strike package.
Wear
strip
Door
side
5 Tape template to door and mark door.
Paper Template
(pages 11 and 12)
Mark vertical line X-X for trim alignment
Mark door
cut-out
Mark 4
holes
Note: Line X-X is a reference line on the paper template used for
trim and exit device alignment. Line X-X shown here should
correspond to line X-X in the trim installation instructions
C
L
6 Prepare lock side of door for device and trim.
See template for drill and
cut-out information
X
X
See trim instructions for
pull side door preparation.
7 Measure to determine length to cut device.
dengilaeciveD
gnitnuomhtiw
seloh
If 5/8” diameter wire access hole
has been predrilled in door, cut
device 5/16” from center of hole.
”61/5
Note
1-3/16” minimum clearance
(with end cap removed)

5
8 If necessary, cut device.
cut device
squareand
remove all burrs
Note: Device must
be cut square for
proper end cap fit
Tape
Cover plate
(flush to pushbar)
Pushbar
Anti-rattle clip
(remove while cutting, then
replace after cutting)
Prepare device for cutting
Cut device square
9 If using a cylinder with a tailpiece, prepare device
and cylinder.
*Tailpiece
Tailpiece
guide
Cut tailpiece
if needed
1/8”
Door
surface
* Tailpiece is attached to
trim or cylinder depending
on application
Rotate tailpiece
guide to match
tailpiece
10 Attach center case to door.
Center
case
Trim (optional)
OR
#325 Sex bolts
(required when
not using trim)
A
11 Install hinge stile mounting bracket.
Secure mounting bracket
Mounting
bracket flush
Level device
Mark and prepare 2 mounting holes
Metal
Wood
1/4” drill
inside
13/32” drill
outside
13/32” drill
thru
C
#425
Sex bolts
(required)
12 Adjust strike as needed.
299/299F/1606 Strike
3/16”
1409 Strike
3/16”
Shim strike for 3/16” clearance to chassis
Shim
(if necessary)
Shim
(if necessary)
13 Install strike support screw.
OR
G
#25
#10-24
METAL WOOD
Z\,” (3 mm) x
1” (25 mm) Deep

6
14 Install 2 support screws and center case cover
Center
case cover
Remove protective film
from pushbar
2 support
screws
B
I
15 Install 2 support screws and center case cover
End cap
D
499F STRIKE INSTALLATION
1. Prepare and install screws through
two strike slots.
2. Install strike hook and additional
strike screws.
3. Template aligns as shown.
Roller
(against door)
 If using a mullion,
holes may be predrilled
#25 Drill
#10-24 Tap
2 places
#7 Drill
Z\v” (6 mm)-
20 Tap
2 places
ZC\cx” (10 mm)
Drill thru for
sex bolts
2 places
MetalWood
#25 Drill
#10-24 Tap
3 places
C
L
Template
(align on C
Land
against strike

7
OPTIONAL EQUIPMENT
CD (Cylinder Dogging) Option
Dog Undog
a
b
c
d
e
f

8
1439 Strike
Frame Preparation
7/8”
7/16”
7/16”
1-9/16” to
face of
door
Blade stop
7/8”
Cut -out
C
L
C
L
RHR shown
(LHR opposite)
1439 Strike
#25 Drill
#10-24 tap
1/8” Drill pilot
1” deep
MetalWood

9
299/299F/1606 Strike
Template
DoorDoor
Stop
Door
Stop
RHR
299F299
Cut paper along this line
and place on door stop
against edge of door
(see picture below)
L
C
Template
LHR
5/8”
1-1/16”
L
C
1-1/16”
Door edge
#25 Drill
#10-24 tap
1/8” Drill pilot
1” deep
MetalWood
1606 Strike
Mullion

10
This page
intentionally
left blank

11
3/16”
1/4”
7/32”
7/8”
1-3/16”
3-1/8”
C
Lof device
33/35A Rim device
Template
LHR
C
Lof device
X
X
7/8”
1-3/16”
3-1/8”
7/8”
19/32”
1/4”
Radius
#25 drill inside
#10-24 tap
1/8” diameter drill
1” deep pilot hole
Metal
Wood
Holes - 2 places
5/16” drill inside
13/32” drill outside (sex bolts)
1/2” drill outside (trim)
13/32” drill thru (sex bolts)
1/2” drill thru (trim)
Metal
Wood
Holes - 2 places
Cut-out
device side only
5/8” deep for
wood door
Align this line
with edge of
strike or roller
Line X-X is a reference line for
trim and exit device alignment.
Line X-X shown here should
correspond to line X-X in the
trim installation instructions

12
33/35A Rim device
Template
RHR
3/16”
1/4”
7/32”
7/8”
1-3/16”
3-1/8”
C
L
Device
C
L
Device
Cut-out
device side only
5/8” deep for
wood door
7/8”
1-3/16”
3-1/8”
7/8”
19/32”
1/4”
Radius
#25 drill inside
#10-24 tap
1/8” diameter drill
1” deep pilot hole
Metal
Wood
Holes - 2 places
X
X
5/16” drill inside
13/32” drill outside (sex bolts)
1/2” drill outside (trim)
13/32” drill thru (sex bolts)
1/2” drill thru (trim)
Metal
Wood
Holes - 2 places
Align this line
with edge of
strike or roller
Line X-X is a reference line for trim and
exit device alignment. Line X-X shown
here should correspond to line X-X in
the trim installation instructions