Vonets VBG1200 User instructions

VONETS - Wireless Module/Finished Product
Wireless module/WiFi product
VM300/VM5G/VBG1200/VAP11AC
Quick Setting Guide

VONETS - Wireless Module/Finished Product
Declaration
Copyright © 2023 Shenzhen HouTian Network Communication Technology Co.,Ltd
All rights reserved, with retained ownership Without Shenzhen HouTian Network
communication Technology Co.,Ltd written authorization, any company or personal can’t
copy, writer or translation part or all contents. Can’tdo commodity distribution for any
commercial or profitable purposes by any ways(electricity, mechanical, photoprint, record or othe
rmethods).
VONETS is the registered trademark of Shenzhen HouTian Network Communication
Technology Co.,Ltd. The other all trademarks or registered trademarks mentioned in this
documents are belong to the individual owners. Theproduct specifications and information
technology mentioned in this manual are just for reference, if any updates, without other notice.
Except for special agreements, this manual is just for user guidance, any statements, information
and so on in this manual can’tconstitute the warranty of any forms.
Product application and secondary development precautions
1. Problems related to wireless interference:
1.1 Use the ping command to test the wireless transmission performance. If it is found that the delay of
the ping packet response is extremely uneven, and there are many responses with a large delay, it can
basically be judged that the wireless has been strongly interfered;
1.2 The product antenna should be kept as far away as possible from sources of interference, such as
switching power supplies, antennas of other modules or wireless products, etc.;
1.3 If it is too close to the antenna of other wireless products, it will cause mutual interference,
resulting in an increase in the transmission bit error rate and a slower transmission rate.At this point, the
wireless signal must be properly attenuated. The methods of attenuating the signal include adding
obstacles, extending the distance, and adding a resistor in series between the antenna feed point and the
antenna, etc., to meet the actual application requirements;
2. Selecting a suitable power supply is the key to good and stable wireless transmission and stable
operation of the product. Improper power supply will cause damage to the product or poor wireless
performance. The selected power supply must meet the voltage range and input power requirements of
the power supply input, and the ripple must be less than the required maximum power supply ripple
(100mV);
Form 1
Transmission Distance Parameters Form
Model
No-barrier point to
point Transmission
Distance
Transmission
Rate (Mbps)
Band
VM300
80m--100m
300
VM5G/VBG1200/VAP11AC
600m--700m
300+900
5G

VONETS - Wireless Module/Finished Product
Form2
Power Supply Parameters List
Model
Power Supply Voltage
Input Power
Typical Power
Supply
VM300
DC5V--15V
≥5W
5V/1A
VM5G/VBG1200
DC5V--15V
≥10W
5V/2A
VAP11AC
DC5V--24V

VONETS - Wireless Module/Finished Product
Contents
Chapter 1 Application Mode...................................................................1
1.1 Bridge + Repeater Mode ..............................................................................................................1
1.2 Router Mode ................................................................................................................................2
Chapter 2 Bridge+Repeater Mode Configuration Instruction ................3
2.1.1 Device Connection ....................................................................................................................3
2.2 Bridge+Repeater Application Configuration................................................................................4
2.3 AP Application Configuration.......................................................................................................7
Chapter 3 Router Mode Configuration Instruction ..................................9
3.1 Change device mode....................................................................................................................9
3.2 WAN port setting........................................................................................................................11
3.2.1 WAN/LAN exchange ............................................................................................................11
3.2.2 WAN Port connection method.........................................................................................12
3.2.3 WAN port wired connect network——DHCP..................................................................12
3.2.4 WAN port wired connect network——PPPoE.................................................................13
3.2.5 WAN port wireless connect network---- WiFi ................................................................13
3.3 Set WiFi hotspot parameters ..................................................................................................15
Appendix Frequently Asked Questions ................................................. 17

VONETS - Wireless Module/Finished Product
1
Chapter 1 Application Mode
1.1 Bridge + Repeater Mode
There are three application modes for the bridge mode of VONETS module/WiFi product: WiFi
repeater, WiFi bridge and WiFi AP.
⚫WiFi Repeater:
VONETS module/WiFi product as WiFi Repeater, it must be configured to source WiFi hostpot
parameters, can be used to extend the wireless signal coverage of existing APs or wifi router .
⚫WiFi Bridge:
VONETS module/WiFi product as WiFi bridge, it must be configured to source WiFi hotspot
parameters, can be used for devices only with Ethernet ports to access wireless networks.
⚫WiFi AP：
VONETS module/WiFi product as WiFi AP, it can achieve wireless access to wired LAN, no
configuration required, plug and play.

VONETS - Wireless Module/Finished Product
2
1.2 Router Mode
⚫VONETS module/WiFi product as WiFi router
The Ethernet port of VM300 module/ VAP11AC finished product defaults to WAN port. The
Ethernet cable defaults to the LAN port. WAN and LAN ports are interchangeable.
The Ethernet cable of VM5G module/VBG1200 WiFi product defaults to LAN port, you must set
“WAN/LAN interchange”so that the Ethernet cable is WAN port to use the broadband
dialing function.
⚫VONETS module/WiFi product is used as a wireless router. WAN port can be set to connect to
the WiFi hotspot for use as a secondary router.

VONETS - Wireless Module/Finished Product
3
Chapter 2 Bridge+Repeater Mode Configuration Instruction
2.1 Method 1: Log in to the device's Web configuration page to configure
2.1.1 Device Connection
Power on VONETS module/WiFi product by 5V/2A power supply, then connect to PC, there are two
connection ways as below:
A. Computer is wired connected to LAN port of VONETS module/WiFi product;
（Recommend Method）
B. The computer wirelessly connects to the WiFi signal of VONETS module/WiFi product, its
default hotspot parameters are as follows:
WiFi SSID: VONETS_****** (corresponding to VONETS device MAC address)
WiFi password: 12345678

VONETS - Wireless Module/Finished Product
4
(After the WiFi parameters are configured, the WiFi will be disconnected, that is normal.)
2.2 Bridge+Repeater Application Configuration
The configuration steps of VONETS module/WiFi product for WiFi repeater and WiFi bridge are
basically the same, so this manual combines the configuration instructions of the two application
modes.
1. After computer is connected to VONETS module/WiFi product, open browser, input configured
page: http://vonets.cfg (or IP: 192.168.254.254), then press Enter;
2. Input User name and Password in login page (both are “admin”), click “Login”button to
enter configured page;
3. “Scan Hotspots”, choose the source hotspots, click “Next”;

VONETS - Wireless Module/Finished Product
5
4. Input “Source wireless hotspot password”, click “Apply”;
⚫IP layer transparent transmission (factory default), transparent transmission of IP layer data,
can meet most of WiFi bridge applications;
⚫MAC layer transparent transmission, transparent transmission of all data above the MAC
layer (link layer) and MAC layer, including IP layer data. MAC transparent transmission can
solve some special applications for MAC layer encryption, such as GoPro camera, Cisco AP,
Hikvision monitoring system, etc;
⚫The option “The configuration parameters of WiFi repeater security is synchronized with
source hotspot”is default ticked, it means the SSID of VONETS repeater is associated with
the SSID of the source hotspot, and the WiFi password is the same as the password of the
source hotspot;
⚫Disable hotspot, if you select “Disable hotspot”on the right side of the SSID, the device
will not transmit the corresponding hotspot and can only be used as a bridge application;
⚫Advanced Setting,include Hot spot authentication match mode, WiFi Signal Motion
Detection and SSA Signal strength alarm threshold,these options here can be kept
unchanged, for instructions on this option, go to www.vonets.com and download the “V
Series WiFi Bridge Advanced Features Instruction”;

VONETS - Wireless Module/Finished Product
6
5. Click “Reboot”, VONETS module will connect to the configured WiFi hotspot automatically, if
connection is successful, the WiFi LED light will flash quickly;