⑦ After installation, power on the circuit breaker or fuse box.
⑧ When the safety light is firmly secured to the junction box, apply silicone sealant around the
bottom of the safety light to prevent water from entering the interior of the safety light.
⑥ Install the security light to the mounting bracket E with screws B .
arrow up
push
B
4.2.2 Typical schematic diagram of the detection scope when the sensor is mounted in different angles.
4.5.3 Instruction about the setting of motion sensor detection scope
a.To determine the detection scope of the motion sensor, a simulation test is required:Walking
along an arc in front of the motion sensor.
b.The motion sensor is less sensitive if in a radial movement. As shown below (picture 1).
c.The motion sensor is more sensitive if in a lateral movement. As shown below (picture 2).
d.Observe the the light. If the light is on,that means the movement has been detected by the
sensor and has gave out lighting command.
e.Stop walking and wait for the light to turn off and then begin walking again.
picture 1 picture 2
Remark:
1.When Sensitivity is set to ON (PIR detection is switched off), the safety light will be constant on
and can control the light ON/OFF by switch.
5. Maintenance
5.1 Cleaning Maintenance
① It is recommended to use a soft damp cloth to clean to prolong the maintenance of the
original appearance of the security light.
② Do not use paints, solvents or other chemicals on the security light as it may cause
premature deterioration or damage to the surface of the light, which is not a cosmetic defect
and is not covered by the warranty.
③ Do not use hoses or automatic cleaners to flush the security light.
5.2 Troubleshooting
The light
can’t be on
1. The light switch is turned off. Turn the light switch on.
2. The power source fuse is blown. Replace the fuse.
3.The influence of daytime light-sensing
function on the lamp. Check again after dark;
4.Bad connection of the wire. Check if the wire is well connected.
①Decrease the “Sensitivity" setting
②If ①can not meet the requirement, relocate
the light fixture to avoid the inappropriate
installation position.
Re-adjust the direction of sensor or lamp
installation position to cover the desired area.
5.The sensor is not set at the correct angle.
1. The motion sensor may be installed
in a relatively dark location. Set the ”Ambient lux” switch to the appropriate
position or reposition the motion sensor.
2.The “Lighting Time” switch is set in the
“Test” position.
For the convenience of user testing, we close
“Test” switch’s light function of “Lighting
Time” specifically, just set to other position,
the light function will restore.
It will start to work normally after the self-test.
The lights turn
off too late in
the Dusk-to-
Dawn setting.
Relocate the light fixture.
The light
comes on for
no apparent
reason.
1.The motion sensor may be sensed small
animals ,cars or other heat source come by.Adjust the “Sensitivity” setting to appropriate
position or reposition the motion sensor.
2.The ambient temperature is much higher
than the human body temperature. Decrease the “Sensitivity” setting or
relocate the light fixture.
The lights
stay on
continuously.
1. The motion sensor may be
picking up a heat source Reposition the motion sensor.
2. The light fixture is on the same
circuit as a motor or transformer. Install the light fixture on a circuit without
high power motors and transformers.
Problem Possible Cause Solution
3.Power on self-test (The lamp will have a
self-test that lasting 1 minute when it ‘s
turned on in the first time and the light will
continue to light up during this time).
The light
comes on
during the
day.
The lights flash
continuously
1. Heat or light from other bulbs
may be turning the motion
sensor on and off.
2. Heat is being reflected from other
objects and may be turning the
motion sensor on and off.
Reposition other bulbs to keep away from
the motion sensor or adjust motion sensor
direction or relocate the light fixture.
Decrease the " Sensitivity "setting or
reposition the motion sensor.
1.The light fixture may be installed in a
relatively dark location, so do not
sensitive to outside light change.
6.The ambient temperature is almost the
same as the human body.
4. Operation
4.1 Setting for the light coverage area
①
②
Left and right to adjust the light irradiation area, the lamp head adjustment direction according tothe arrow
indicates direction 1, direction 2 adjustment.
Far and near to adjust the light irradiation area, the lamp head adjustment direction according tothe arrow
indicates direction 3, direction 4 adjustment.
1
2
3
4
① Adjust the switch of “Lighting Time” can set the duration of lighting time when the sensor detect
an object movement, then it will turn the light on (The duration time when the objects stop
movement), it can be set to 15min,5min,1min and Test(5s).
② When set on Test(5s) position, it is used to test for installation, which is not controlled by
ambient lux, and the light will stay on for 5 seconds.
4.3 Setting for the lighting time
4.4 Setting of colour temperature
① Slide the "CCT" switch toset the working colour temperature of the safety light,
which can be set to5000K, 4000K, 3000K respectively.
colour temperature
5000K
4000K 3000K
4.5 Setting for the motion sensor detection scope
① If you need to adjust the detection scope,the sensor can be rotated clockwise or counterclockwise
to the maximum of 225 degree.
4.5.1Adjustment of the detection scope
225° 45° the sensor can be rotated
clockwise to the maximum
of 45 degree.
the sensor can be rotated
counterclockwise to the
maximum of 225 degree
4.2.1 As shown in the picture 1(schematic diagram of the max detection scope). The sensor can be
adjusted up 4 °or down 130°. When fixture installed on the vertical wall, adjust the sensor to
different degree can change the detection distance. When the sensor is mounted at a
the detection distance is the largest.The detection distance and sensitivity
4.2 Adjustment and setting for the detection distance
picture 2picture 1
130°
45°
40°
52.49ft
4.5.2 Setting for the detection distance means the setting of sensitivity
slide the “Sensitivity ” switch can set the sensitivity of the sensor which means changing the
sensor’s detection distance, it can be set as high,mid, low and ON(turn off the function of PIR
detection and the the light will be constant on).
⑤ Connect the black wire on security light to terminal “L”, white wire to terminal “N”, screw on the wire
nut C to secure.
C
L
N
C
Typical detection distance when fixture is installed on the vertical wall
(lateral movement)
Mounting angle
Horizontal direction
High
52.49ft
Mid
39.37ft
Low
26.25ft
ON
turn off the function of PIR detection
and the the light will be constant on
The induction range is in the profile frame
0°
22.5°
45°
67.5°
90° 112.5°
135°
157.5°
180°
13.12
26.25
39.37
52.49
65.62ft
Sensitivity High Sensitivity Mid Sensitivity Low
52.49ft52.49ft
