Voxx Electronics Prestige APS510Z User manual

OWNER’S GUIDE
MODEL APS510Z
VOXXELECTRONICS.COM

2APS510Z Owners REV.C
Using Your Remote Control................................................................3
Arming the Security System ..........................................................3
Disarming the Security System .....................................................3
Two Stage Door Unlock (optional).................................................3
Activating Trunk Release (optional) ..............................................3
Activating AUX Output (optional) ..................................................3
Using the Personal Protection Alarm ............................................3
Bypassing the Shock Sensor.........................................................4
Alarm City Mode ..............................................................................4
Valet Mode............................................................................................4
Manually Overriding the Security System.........................................4
Custom Code Valet Override ..............................................................5
User Selectable Notication Chirps...................................................6
User Selectable LED............................................................................6
Programmed Transmitter Notication ...............................................6
Status LED, Light Flashes and Siren/Horn Indications ...................7
Remote Control Programming ...........................................................8
Replacing Remote Control Batteries.................................................8
Warranty Information ........................................................................ 11
Table of Contents

32020 Voxx Electronics Corporation. All rights reserved.
Arming the Security System
To arm the system, exit the vehicle, close all doors, then press the button.
The parking lights will ash one (1) time, indicating the system is armed, has
locked the doors (if equipped and connected) and activated the starter disable
feature. The LED status indicator will blink steadily, once per second.
NOTE: The system is equipped with a feature called Silent Choice. If enabled,
the system requires a second press of the button to activate an audible
arming response from the vehicle.
*Throughout this manual, ‘press’ refers to pressing for less than 1 second; ‘press and hold’ refers to pressing for
more than 3 seconds.
Two Stage Door Unlock (Optional)
If this feature is enabled on your system, pressing the button one time will
unlock only the driver’s door. Press again within three (3) seconds to unlock
the remaining doors.
Disarming the Security System
To disarm the system press the button. The parking lights will ash two
(2) times, indicating the system is disarmed and has unlocked the doors (if
equipped and connected).
NOTE: The system is equipped with a feature called Silent Choice. If enabled,
the system requires a second press of the button to activate an audible
disarming response from the vehicle. If your system is set up for two (2) step
unlock, a third press of unlock will activate the audible response.
Activating the AUX Ch. 4 & 5 Output (Optional)
AUX channel output is an optional feature and programming is required at the
time of installation. Please consult your dealer for more information.
Using the Personal Protection Alarm (Panic)
Press and hold the or button for three (3) seconds to activate the personal
protection alarm. During panic mode, the normal function of the transmitter
buttons will be suspended. The transmitter’s and buttons can be used to
lock and unlock the door (if the option is installed). To stop the alarm, press
and hold the or button on the transmitter again for three (3) seconds. The
system will automatically stop after thirty (30) seconds.
Activating the Trunk Release Feature (Optional)
If this feature is enabled on your system, pressing and holding the button
for three (3) seconds will open the vehicle’s trunk or hatch.
Using Your Remote Control

4APS510Z Owners REV.C
Bypassing The Shock Sensor
The included security shock sensor has two stages of detection, Warn-Away
and Full Trigger. To arm the system and shock sensor press the button. The
system will beep and the lights will ash one (1) time.
To Arm the system and bypass the Warn-Away detection stage press the
button two (2) times within ve (5) seconds.
To Arm the Alarm the bypass both detection stages press the button three
(3) times within ve (5) seconds.
City Mode
City Mode allows the user to change the sound of the alarm system to make
it easily identied when the alarm is triggered. To enter City Mode press the
button four (4) times within ten (10) seconds.
Valet Mode
When valet mode is activated the status LED will light solid, and all security
functions will be disabled. To enter or exit valet mode simply follow the steps
outlined below:
1. Turn the vehicle’s ignition ON.
2. Push and hold the valet button for ve (5) Seconds.
3. The LED will turn on solid when valet mode is active.
4. Release the valet button.
Manually Overriding the Security System
Your system can be disarmed without the use of the transmitter. This is
necessary to operate your vehicle if the transmitter is lost or its battery fails. To
by-pass the alarm system;
1. Open the vehicle door. The alarm will sound.
2. Turn the ignition key to the ON position.
3. Within ten (10) seconds, press and release the valet button.
The alarm system will stop sounding and enter the (by-passed) mode. You
can now start and operate the vehicle normally.

52020 Voxx Electronics Corporation. All rights reserved.
Custom Code Valet Override (Optional)
Unlike the default Valet Override, Custom Code Override is a user
personalized code that o󰀨ers a higher lever of security. If the user chooses to
use Custom Code Override, Feature Bank 2 ; Feature 9 must be programmed
for “Custom Code”. Once the option has been selected the code must be
programmed. Once the Custom Code is programmed it cannot be changed
without rst disarming the alarm.
Custom Code Override Procedure
The Custom Code is made up of 2 numbers. Each chosen number must be
between digits 1-9. The default Custom Code is “11”. To disarm the alarm
using the Custom Code option:
1. Turn the vehicle ignition to ON.
2. Within ve (5) seconds, Press the valet button one (1) time.
3. Within ve (5) seconds, Turn the ignition OFF/ON.
4. Within ve (5) seconds, Press the valet button one (1) time.
5. Turn the vehicle ignition to OFF then ON to start the vehicle.
Custom Code Programming Procedure
In this example, the user has selected Custom Code “23”. To program a user
selected custom code:
Start with the alarm disarmed.
1. Turn the ignition to the ON position.
2. Within ten (10) seconds, press the valet button three (3) times to
enter programming.
3. Within ten (10) seconds, Cycle the ignition OFF/ON, OFF/ON, OFF/
ON. The system will beep one (1) time.
4. Within ten (10) seconds, Press the valet button two (2) times. This
number will indicate the rst digit of the chosen Custom Code.
5. Within ten (10) seconds, Cycle the ignition OFF/ON.
6. Within ten (10) seconds, Press the valet button three (3) times. This
number will indicate the second digit of the chosen Custom Code.
7. Cycle the ignition OFF.
If the Custom Code was accepted the LED will ash the rst number (2),
pause, then the second number (3). This will repeat two (2) more times to
conrm the Custom Code entry. If after fteen (15) seconds the LED does not
ash please repeat steps 1-7.