Voxx Electronics PURSUIT User manual

INSTALL GUIDE
WIRELESS KEYPAD
ADVENTPRODUCTS.COM

22020 Voxx Electronics Corporation. All rights reserved.
Installation
Installation
The Pursuit wireless keypad is designed to be placed on the driver’s door “B
Pillar.” The rear slanted keypad should be places on the door pillar with the
keypad angled to the rear.
Clean and prep the installation area with a isopropyl alcohol based solution.
Allow the surface to dry completely before placing the keypad on the pillar.
Remove the red plastic backing from the adhesive pad on the rear of the
keypad. Place the keypad on the door pillar so that the keypad is angled
(Slanted) to the rear. Press rmly for 60 seconds to ensure the adhesive
properly adheres to the vehicle.
Programming
Locate the valet override button inside the vehicle. The vehicle’s door must be
open until programming is complete.
To Program the keypad:
1. Set the vehicle’s ignition to the ON position.
2. Press and release the valet override button three (3) times. The
system will beep one (1) time to conrm it has entered remote
programming.
3. Press and release the 7/8 and the 9/0 buttons. The system will
beep one (1) time to conrm the keypad has be programmed
successfully.
Note: The security system can store up to four (4) remote controls in its
memory banks. This can be any combination of four (4) keypad or key
chain remote controls. Any remote control programmed after four (4) will
automatically delete the oldest remote control in the memory bank.
Programming Personal Pin Code (Optional)
The keypad master unlock code cannot be changed or deleted. The keypad
can learn and store a personal pin code. This code can be changed at any
time.
To Program a Personal Pin Code:
1. Enter the ve (5) digit master code.
2. Within ve (5) seconds press and hold the 1/2 button for one (1)
second. The keypad LED will ash two (2) times.
3. Within ve (5) seconds, enter the new Personal Pin Code. The
keypad LED will ash two (2) times to conrm the Pin Code has
been stored.

32020 Voxx Electronics Corporation. All rights reserved.
Using Your Remote Control
Locking the Vehicle
To lock the vehicle, exit the vehicle, close all doors, then press and release
the 7/8 & 9/0 buttons at the same time. The parking lights will ash one (1)
time, indicating the system is armed, has locked the doors (if equipped and
connected) and activated the starter disable feature. The LED status indicator
will blink steadily, once per second.
NOTE: The system is equipped with a feature called Silent Choice. If enabled,
the system requires a second press of the 7/8 & 9/0 buttons to activate an
audible arming response from the vehicle.
Two Stage Door Unlock (Optional)
If this feature is enabled entering the ve (5) digit unlock code will unlock the
driver’s door only. To unlock all doors, enter the ve (5) digit unlock code then
press and release the 3/4 button within ve (5) seconds
Unlocking the Vehicle
To unlock the vehicle enter the ve (5) digit unlock code. The parking lights will
ash two (2) times, indicating the system is disarmed and has unlocked the
doors (if equipped and connected).
Activating the Trunk Release Feature (Optional)
If this feature is enabled on your system, enter the ve (5) digit unlock code
then press and release the 7/8 button within ve (5) seconds.
Using the Personal Protection Alarm (Panic)
To activate the Panic alarm, enter the ve (5) digit unlock code then press and
hold the 5/6 button for ve (5) seconds. To stop the alarm, enter the ve (5)
digit unlock code or press the lock functions (Press and release the 7/8 & 9/0
buttons). The system will automatically stop after thirty (30) seconds.
Deleting Personal Pin Code
To deleted the Personal Pin Code:
1. Enter the ve (5) digit master code.
2. Within ve (5) seconds press and hold the 1/2 button for ve (5)
second. The keypad LED will ash four (4) times to conrm the pin
code has been deleted.

42020 Voxx Electronics Corporation. All rights reserved.
Voxx Electronics Corporation.
Customer Service 1-800-225-6074
www.AdventProducts.com
PATENTED: www.voxxintl.com/company/patents
FCC COMPLIANCE
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
any interference that may cause undesired operation.
Warning!
Changes or modications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.