VTech Baby Push and Ride Alphabet Train User manual

© 2012 VTech
Printed in China
91-002305-024UK
User’s Manual
Push and Ride
Alphabet Train

3
INTRODUCTION
Thank you for purchasing the VTech®Push and Ride Alphabet Train
learning toy!
The VTech®Push and Ride Alphabet Train will take your child on a
journey through letters, numbers, music and more. Entertaining sound
effects, dancing lights and fun melodies reward your child’s curiosity.
Introduction
5 NUMBER
BUTTONS
13 DOUBLE-SIDED
LETTER BLOCKS
BOOK WITH
6 PAGES
ATTACHABLE
CARRIAGE WITH
BLOCK STORAGE
ON/OFF/MODE
SELECTOR
SWITCH
BLOCK
DROP SLOT
BLOCK
SLOTS
VOLUME
CONTROL
SWITCH

4
INCLUDED IN THIS PACKAGE
- One engine
- One engine handle
- Two back engine wheels
- One soft hinge and two screws
- One instruction manual
Included in This Package
- Four carriage wheels with
two axle trees, four blue
covers and eight screws
- 13 double-sided letter blocks
- Two front engine wheels
- One carriage

5
WARNING:
All packing materials, such as tape, plastic sheets, packaging locks and
tags are not part of this toy, and should be discarded for your child’s
safety.
NOTE: Please keep user’s manual as it contains important information.
GETTING STARTED
BATTERY INSTALLATION
1. Make sure the unit is turned OFF.
2. Locate the battery cover on the back of the
unit. Use a coin or a screwdriver to loosen
the screw.
3. Install 3 new ‘AA’ (AM-3/LR6) batteries
following the diagram inside the battery box.
4. Replace the battery cover and tighten the
screw to secure.
BATTERY NOTICE
• Usenewalkalinebatteriesformaximumperformance.
• Useonlybatteriesofthesameorequivalenttypeasrecommended.
• Donotmixdifferenttypesofbatteries:alkaline,standard(carbon-
zinc) or rechargeable (Ni-Cd, Ni-MH), or new and used batteries.
• Donotusedamagedbatteries.
• Insertbatterieswiththecorrectpolarity.
• Donotshort-circuitthebatteryterminals.
• Removeexhaustedbatteriesfromthetoy.
• Removebatteriesduringlongperiodsofnon-use.
• Donotdisposeofbatteriesinfire.
• Donotchargenon-rechargeablebatteries.
• Remove rechargeable batteries from the toy before charging (if
removable).
Getting Started

6
Assembly Instructions
• Rechargeable batteries are only to be charged under adult
supervision.
Disposal of batteries and product
The crossed-out wheelie bin symbols on products and
batteries, or on their respective packaging, indicates they
must not be disposed of in domestic waste as they contain
substances that can be damaging to the environment and
human health.
The chemical symbols Hg, Cd or Pb, where marked, indicate
that the battery contains more than the specified value of
mercury (Hg), cadmium (Cd) or lead (Pb) set out in Battery
Directive (2006/66/EC).
The solid bar indicates that the product was placed on the
market after 13th August, 2005.
Help protect the environment by disposing of your product or
batteries responsibly.
Formoreinformation,pleasevisit:
www.recycle-more.co.uk
www.recyclenow.com
With the VTech Push and Ride Alphabet Train, safety comes first.
Toensureyourchild’ssafety,adultassemblyisrequired.
Please ensure that all assembled parts are securely locked into
position before use.
Assembly Instructions
1. Install the two green front wheels onto
the front of the engine by placing them
over the yellow front axles. Push the
wheels onto the axles until you hear
a click. Once you have installed the
wheels, they cannot be removed.

7
2. Install the two green back engine wheels
onto the back of the engine by inserting
them into the yellow sockets at the back
of the train. Push the wheels into the
sockets until you hear a click. Once you
have installed the wheels, they cannot
be removed.
3. Install the four green carriage wheels with axle trees into the sides
of the bottom of the carriage. Place the covers over the axles. Use
a screwdriver to tighten the screws.
4. Position the handle so that the curved
part of the handle faces the back of
the engine. Insert the handle into the
hole in the top of the engine until you
hear a click. Once you have installed
the handle, it cannot be removed.
5. Position the soft, blue hinge so that its large hole is facing up and to
the front. Insert the hinge into the hole at the front of the carriage,
use a screwdriver to tighten the two screws on the bottom of the
carriage.
Assembly Instructions

8
6. To attach the carriage to the engine,
insert it into the slot at the back of
engine. You will hear a click, which
lets you know the carriage is attached
correctly.
7. To detach the carriage from the engine, press and hold the blue
button under the end of the engine, pull the carriage from the slot.
PRODUCT FEATURES
1. ON/OFF/MODE SELECTOR SWITCH
To turn the unit ON, slide the red ON/
OFF/MODE SELECTOR SWITCH
located at the top of the engine to the
Learning Mode ( ) or Discovery
Mode ( ) position.To turn the unit OFF,
slide the ON/OFF/MODE SELECTOR
SWITCH to the OFF ( ) position.
Product Features

9
2. VOLUME CONTROL SWITCH
To adjust the volume, slide the
VOLUME CONTROL SWITCH to the
LOW VOLUME or the HIGH VOLUME
position.
3. AUTOMATIC SHUT-OFF
To preserve battery life, the VTech®Push and Ride Alphabet
Train will automatically power-down after approximately 78 seconds
without input.The unit can be turned on again by pressing any button.
ACTIVITIES
1. Slide the red on/off/mode selector
switch located at the top of the
engine to the Learning Mode ( ) or
Discovery Mode ( )position to turn
the unit on.You will hear a train engine
sound, entertaining phrases and music.
The lights will flash with the sounds.
2. Press the elephant button to hear an
elephant sound effect followed by fun
phrases and sing-along songs. The
lights will flash with the sounds.
Activities

10
3. Press the number buttons to learn
about numbers in the Learning
Mode and learn about colours in the
Discovery Mode. The lights will flash
with the sounds.
4. Turn the book’s pages to learn about
letters and objects and listen to fun
stories in both modes. The lights will
flash with the sounds.
5. Place the blocks into the train’s block
slots to learn letters and objects in
both modes. Upbeat melodies and fun
sounds will accompany the play. The
lights will flash with the sounds.
6. Drop the blocks into the drop block slot
at the top of the train and they’ll slide out
the back into the attachable carriage
storage area.
7. If there is no input to the unit after approximately 10 seconds, you will
hear a fun sing-along song. After another 10 seconds if there is still
noinput,youwillhearaquestion,whichwillencouragethechildto
find the correct block according to the book page. After another 10
seconds if there is still no input, you will hear the phrase “Bye-bye,”
then the unit will automatically power-down.
Activities