VTOMAN Jump 600 User manual

Thank you for choosing VTOMAN portable power station.
VTOMAN
TOOLS & BATTERIES
User Manual
Model: Jump 600
WWW,VTOMAN.COM
Scan to get more information about VTOMAN products

TECHNICAL SPECIFICATIONS:
Product Model Jump 600
Battery Capacity 640Wh
Battery Type LiFePO4
DCInput 12-30V(Max 65W)
2xAC Output Total 600W (Peak 1200W) 110V~60Hz Pure Sine Wave
3xDC Output 1x Car Charger(12V 10A) + 2x DC5521(12V 10A)
2xUSB-AOutput 5V2.4A
1xUSB-AQC3.0 Output 5V 3A/9V 2A/12V 1.5A(Max 18W)
1xUSB-CPD Output 5V 3A/9V 3A/12V 3A/15V 3A/20V 3A(Max 60W)
1x 12V Jump Starter Output | Start current:500A; Peak current: 2000A
LED Light Power 12w
Operating Temp -4°F~131°F (-20°C~55°C)
Charging Temp 32°F~131°F (0~55°C)
Product Size 10.4x8.7x8.5in (264X 220X 216mm)
NetWeight 15.4 b (6.99Kg)
Instruction of Usage
1.Power on---Press any button on the state of standby.
2.Power off-—Close all outputs by manual operation, into the state of standby after 30mins.
3.Power offin 6 hours
The last time open any output, continue 8 hours, if the output loading current lower
than the setting current, it will be power off after 30min later, or after 6 hours the loading
current higher than the setting value, the output will be keep on until the loading current
lower than the setting value.
4.The over high temperature or the over low temperature both will be effect on the
battery's capacity, the unit allow to charge under the temperature within 0~55°C,
supply the power under the temperature within-20°C~55°C.
5.Advise to full charge before the first time using to avoid the lack of power make you
worse usage experience.

Jump Start 12V Vehicle Instruction:
1.Plugtheblue endof the jumpercableinto the
jump start port on the power station, and make
sure the Cable Indicator is off.
2.Connect the red clamp to the positive(+) of
battery terminal,and black clamp to the negative
(-) of battery terminal.
3.Perform the following operations according to the different states of the
indicator lightsonthe jumpercable:
GREEN LIGHT on:
Telling the connection
is correct and the
circuit is working, you
can turn on the engine
to jump-start directly.
GREEN LIGHT
blinking: Saying the
vehicle battery is low,
press the “BOOST"
button, wait GREEN
LIGHT becomes solid,
RED LIGHT on with
buzzing: Telling the
connection iswrong, and
buzzing to alarm to correct
the clamps as step 2
mentioned above, wait until
the GREEN LIGHT isonto
turn on the engine.
No Lights on, No buzzing:
Saying the vehicle's battery
maybe damaged, after
| confirm the clamps
Connection is correct, press
the “BOOST” button, wait
then turn on the engine
within 30s.
GREEN LIGHT is on, and
then turn on the engine
within 30s.
4.Start your vehicle. And when the vehicle is started, please remove the
jumper cable from the vehicle battery, and leave the vehicle's engine
running.
Ifyouneedthisjumpercable,please goto VTOMAN
storeto buy it.
Lighting Opening Method
Click the light switch button, the display islit, and it isin low light mode; click the LED
light switch again to switch from low light to medium light mode; click the LED light
switch again to switch from medium light to intensity light Mode; click the LED light
switch again to enter the burst flash mode; click the LED light switch again to enter
the SOS mode; in the SOS mode, click the light button to turn off the light.