WAC Lighting 4011 User manual

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JANUARY 11, 2016 4:32 PM
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
1
INSTALLATION INSTRUCTION
Step and Wall Light
4011
WARNING
IMPORTANT: NEVER attempt to do any work without shutting o the electricity.
1. Read all instructions before installing.
2. System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
3. Place the wall switch in the“OFF”position.
4. Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch“OFF”the circuit breaker switch(es) that control the power to the
space that you are working on.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out
or broken. Failure to follow this instruction may invalidate the UL/CUL listing of this xture.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les règlements locaux.
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
- Toujours mettre le fusible ou le disjoncteur en position arrêt dans la pièce ou des travaux électriques sont prévus
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez
pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler
l’homologation UL /CUL du luminaire.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e instalación de esta lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de alimentación principal
en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni utilice
piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación UL/CUL esta lámpara.
Ruber Washer
Qty: 2pcs
Mounting Screw
Qty: 2pcs
Wire Nut
Qty: 2pc
Mounting Bracket
Qty: 1pc
Junction Box Screw
Qty: 2pc
MOUNTING ACCESSORIES INCLUDED IN BOX
*Note: Transformer is required to power the xture. (sold separately)

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JANUARY 11, 2016 4:32 PM
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
2
STEP 1: DETERMINE MOUNTING POSITION
*Note: Transformer is required to power the xture. (sold separately)
1. Make sure the main power supply to your transformer
is turned o.
2. Install a 2’’ by 4’’ junction box, and ensure it is water-tight
for outdoor use.
3. Secure the mounting bracket to the junction box using
two 8-32 junction box screws.
4. Connect the xture wires to the landscape wires from the
transformer using the wire nuts provided.
5. Place all wiring and connectors back in the junction box.
6. Use the rubber washer and mounting screw to install and
secure the xture to the mounting surface.
Note: It is recommended that the installer run a bead
of clear, outdoor-rated silicone (GE RTV-162 or
equivalent, provided by others) caulk between
gasket or back of xture and mounting surface to
prevent seepage of water into xture)
Mounting Bracket
Junction Box
Screws
Mounting Surface to prevent seepage of water into xture
Wire Nuts
Rubber Washer
INSTALLATION INSTRUCTION
Step and Wall Light
4011