WAC Lighting Grand Accent 5212 User manual

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. 1
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
Grand Accent
5212
WARNING
1. Read all instructions before installing.
2. System is intended f
3. Place the wall switch in the“OFF”position.
4. Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch“OFF”the circuit breaker switch(es) that control the power to the
space that you are working on.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out
or broken. Failure to follo
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électr
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
- Toujours mettre le fusible ou le disjoncteur en position arrêt dans la pièce ou des travaux électriques sont prévus
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez
pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler
l’homologation UL du luminaire.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
-Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e instalación de esta lámpara.
- do con el código eléctrico nacional y las normas locales.
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de alimentación principal
en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni utilice
piezas gastadas o rotas. El incumplimiento de esta indicación podría in
This instruction apply to the model(s) below:
5212

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. 2
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Rated Wire Nut
Qty: 3pcs
Hex Key
Qty: 1pcs
7MPE155003
1/16“
Adjustable Shroud
Qty: 1pc
MOUNTING ACCESSORIES
1. .
2. Excavate a trench for the UF supply line cable or
conduit/conductors and the Landscape Power Stake.
The Landscape Power Stake requires approximately
a one (1) square foot hole to facilitate installation.
The excavated should be approximately 15” deep.
This will allow the hex-head set screw on the Power
Stake to remain above ground when the installation is completed.
3. Turn the hex-head set screw counterclockwise to
remove the Power Stake Cap from the top of the PVC Light Stake
4. Feed the light xtures black, white, and ground wires
through the top of the Power Stake Cap. Then, thread
the light xture until it’s rmly attached to the Power Stake Cap.
5. Fed the incoming supply line cable through the slanted
bottom of the PVC Light Stake. Note: If you are wiring
multiple light xtures in series, also bring the second
supply line cable into the PVC Light Stake.
6.
Using appropriate UL Listed wire connectors, splice the white
incoming supply line’s black wire(s). Then splice the ground
ground wire(s).
INSTALLATION INSTRUCTION
Grand Accent
5212
Light Fixture
Power Stake Cap
PVC Stake
Incoming UF
supply line
cable of
conduit
Cap Locking Screws
1/2" NPT Threaded Hole

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. 3
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
Grand Accent
5212
7. Place the Power Stake Cap with attached light xture over
the PVC Light Stake.Carefully push the incoming supply line cable
down into the PVC Light Stake. Tighten the hex-head screw
clockwise on the Landscape Power Stake Cap.
8. Lower the completely wired and assembled Landscape
Power Stake into the excavated hole.
Make sure that the excavated hole is approximately 13”
deep to allow the hex-head set screw on the Landscape
Power Stake Cap to remain above the ground.
9. er Stake.
10. Repeat steps for other xtures in the same electrical circuit
11. Turn the main pow
light up.
Step 4: Aiming the Fixture
12. Tilting: Loosen the joint scr
to the desired direction before retightening the screw.
13. Rotating: Loosen the moun
the desired position before retightening the knob.
Mounting Knob
Tilting
Rotating
Joint Screw

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. 4
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Step 3: Dimming Adjustment:
14. Use a Phillips head screwdriver to adjust the dimming dial.
15. Rotate until the arrow on the dial is pointed at the desired
wattage. The wattage may be adjusted to the pre-existing tabs
or any value in between.
16. The lower the watage,the dimmer the xture will be.
17. Please refer to the yellow tag to determine the size of the
required transformer.
Step 4: Beam Angle Adjustment:
18. Note the four pre-determined beam angles on the beam angle
changing dial.
19. Remove shroud before adjusting beam angle (See step 7)
20. Use the provided Hex Key to sightly loosen the set screw one or
CAUTION: Do not r
for service instruction.
21. te the dial until the arrow is
aligned with the desired beam angle. This beam angle may be
one of the pre-determined markings or any number in between.
CAUTION: Keep the arro
the beam angle range.
22. Tighten the set screw until it stops. Do not over tighten.
23. Install the shroud
Step 5: Shroud Adjustment
24. Loosen the thumb screw on the shroud.
25. Rotate the shroud until it is in the desired position to properly
26. Retighten the thumb screw to lock the shroud in place.
Shroud
Thumbscrew
INSTALLATION INSTRUCTION
Grand Accent
5212
*16W
*13W
*21W
*26W
*31W
Model: 5212
*Numbers not printed
Beam Angle Dial
Turn dial with
other hand
Hex Key

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
5
INSTALLATION INSTRUCTION
Grand Accent
5212
ACCESSORIES
I. Color Lens
Installation: Loosen the thumbscrew and remove the shroud.
Place the color
the shroud.
II. Surface/ Wall Mount Accessory
surface like wood or cement or as alternative to the power stake.
In addition, surface mount accessory can also be used in wall mount
applications.
Installation: Mount the weatherproof junction box onto the surface
Connect all wires in the junction box. Then, mount the Canopy onto
the junction box with screws and gasket. Make sure the whole unit
is sealed properly from water.
Note: all components must be UL Listed.
Weatherproof
Junction Box
Mounting
Canopy
Mounting
Screws
Light Fixture
Wall
Gasket
Lighting Fixture
Mounting Screws
Mounting Canopy
Gasket
Weatherproof Junction Box
Conduit
Lens 25
Shroud