WAC Lighting dweLED 649 Series User manual

1
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
HARDWARE
INSTALLATION INSTRUCTIONS
Wire Connector
Qty: 3pcs+1 Extra
Junction Box Screw
Qty: 2pcs+1 Extra
Mounting Screw
Qty: 1 Extra
7EAC112201 7MPF0415C2
#8-32x5/8 SS
7MPF0409S3(AL)
4MPF040902W5(WT)
5/32"-32X5/16
A
BC
Wire Connector
Qty: 1 Extra
7EAC140901
D
Wire Connector
Qty: 3pcs+1 Extra
Junction Box Screw
Qty: 2pcs+1 Extra
Mounting Screw
Qty: 1 Extra
#8-32x5/8 SS
7MPF0415C27EAC112201 7MPF0409S3(AL)
4MPF040902W5(WT)
5/32"-32X5/16
A
BC
Wire Connector
Qty: 3pcs+1 Extra
Mounting Screw
Qty:1 Extra
Rubber Gasket
Qty:1 Extra
B
AC
178 – LED Wall Sconce
WS-17825/WS-17837
649 Outdoor Wall Sconce
WS-W64905/ WS-W64906/ WS-W64908
•Read all instructions before installing.
•System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
•
•Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or acces-
sories designated for use by WAC Lighting/dweLED/Modern Forms. Substitution of parts or accessories not designated for use with this product
by WAC Lighting/dweLED/Modern Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized
dealer or the manufacturer if any parts are damaged or missing.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
•Lisez toutes les instructions avant l’installation.
•Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux règlements
locaux.
•Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits WAC Lighting/dweLED/Modern Forms. Remplacer des pièces ou
accessoires non conçus pour ce produit WAC Lighting/dweLED/Modern Forms pourrait causer des dommages corporels ou matériels et pourrait
également causer l’annulation de la garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endom-
magées.
Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal areasMAINTENANCE NOTE:
clean all external surfaces of the xture once every two weeks with a wet cloth.
Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons auxNOTE D’ENTRETIEN:
clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec un chion
humide.
dweLED retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Jan 2019

dweLED retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Jan 2019 2
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTIONS
178 – LED Wall Sconce
WS-17825/WS-17837
PREPARATION
1.
2.
CONNECTING THE WIRES (Fig. 2)
3.
4. Connect the driver input wires with junction box wires as shown in Fig.2, making sure that all wire connectors (A) are secured. If your outlet
the mounting plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
MOUNTING THE FIXTURE (Fig. 1)
5. Secure the mounting plate to the junction box using junction box screws (B). The side of the mounting back plate marked “GND” must face
out.
6.
7.
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring
Fig. 1
D
WS-17825&WS-17837 Back plate
C
DA
B
C
Mounting Screw
Fixture
B
Junction Box Screw
Mounting Plate
Driver 2 3/4"L 1 1/4"W 1 3/16"H
A
Wire Connector
Junction Box
Female/Maleendconnector
7MBC151106
Mounting Screw
Rubber Gasket
B
C
Wire Connector
A
Junction Box Screw
Backplate
Junction Box
Junction Box Wires
13
4"13
8"
WS-W64905: 3 7/8" WS-W64906: 4 1/8" WS-W64908: 5 7/8"
WS-W64905: 4 1/4"
WS-W64906: 5 1/4"
WS-W64908: 6 1/8"
Back Plate Dimensions
3. Remove the mounting screw (B) and the rubber gasket (C) from the mounting back plate.
ed. If your outlet box
wire directly to
the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
4. Secure the mounting plate to the junction box using junction box screws.
NOTE: The side of the mounting back plate marked “GND” must face out.
MOUNTING THE FIXTURE (Fig. 1)
ssary for installation.
PREPARATION
CONNECTING THE WIRES (Fig. 2)
7. To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. indoor/outdoor silicone sealant) to outline
.3.
COMPLETING THE INSTALLATION (Fig. 1)
Junction Box
Caulking
Fig. 3 Sealing
649 Outdoor Wall Sconce
WS-W64905/ WS-W64906/ WS-W64908