WAC Lighting 5222 User manual

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. NOVEMBER, 2019
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE CIRCUIT BREAKER BEFORE BEGINNING.
- Read all instructions before installing.
- System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
- When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
- Retain installation instructions for future maintenance reference.
- Risk of electric shock. Install all luminaires 10 feet (3.05m) or more from a pool, spa, or fountain.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by WAC Lighting. Substitution of parts or accessories not designated for use with this product by WAC Lighting
could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts
are damaged or missing.
MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal
areas clean all external surfaces of the xture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
- Lisez toutes les instructions avant l’installation.
- Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
- Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
- Risque de choc electrique. Installez tous les luminaires de (3.05m) (10 ft.) ou plus d’une piscine, d’un spa ou d’une fontaine.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement avec
les pièces et/ou accessoires fournis pour être utilisés avec les produits WAC Lighting. Remplacer des pièces ou accessoires non conçus pour ce
produit WAC Lighting pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez
contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons aux
clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec un
chion humide.
INSTALLATION INSTRUCTIONS
Adjustable Beam Wall Wash
5222
THE INSTRUCTIONS APPLY TO THE MODEL BELOW:
HARDWARE
Rated Wire Nut
7ECA2414011
Qty: 3 pcs
Horizontal Shroud Assembly
5220-HSHR-BK
5220-HSHR-BZ
5220-HSHR-BBR
Qty: 1 pc
Hex Key
7MPE155003
Qty: 1 pc
5222

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. NOVEMBER, 2019
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
STEP 1: DETERMINING THE LOCATION
1. Make sure your main power is o.
2. Excavate a trench for the UF supply line cable or
conduit/conductors and the Landscape Power Stake. The
Landscape Power Stake requires approximately a one (1)
square foot hole to facilitate installation. The excavated should
be approximately 15” deep. This will allow the hex-head set
screw on the Power Stake to remain above ground while the
installation is completed.
3. Turn the hex-head set screw counterclockwise to remove the
Power Stake Cap from the top of the PVC Light Stake.
4. Feed the light xtures black, white, and ground wires through the
top of the Power Stake Cap. Then, thread the light xture until it’s
rmly attached to the Power Stake Cap.
5. Fed the incoming supply line cable through the slanted bottom
of the PVC Light Stake.
NOTE: If you are wiring multiple light xtures in series, also bring
the second supply line cable into the PVC Light Stake.
6. Using appropriate UL Listed wire connectors, splice the white wire
from the light xture to the incoming supply line cable(s) white
wire(s), and the black wire from the light xture to the incoming
supply line’s black wire(s). Then splice the ground wire from the
light xture to the incoming supply line cable(s) ground wire(s).
7. Place the Power Stake Cap with attached light xture over the PVC
Light Stake. Carefully push the incoming supply line cable down
into the PVC Light Stake. Tighten the hex-head screw clockwise on
the Landscape Power Stake Cap.
8. Lower the completely wired and assembled Landscape
Power Stake into the excavated hole. Make sure that the
excavated hole is approximately 13” deep to allow the
hex-head set screw on the Landscape Power Stake Cap to
remain above the ground.
9. Back ll the soil around the Landscape Power Stake.
10. Repeat steps for other xtures in the same electrical circuit.
11. Turn the main power supply back on and make sure the
xtures light up.
INSTALLATION INSTRUCTIONS
Adjustable Beam Wall Wash
5222
Light Fixture
Power Stake Cap
PVC Stake
Incoming UF
supply line
cable of
conduit
Cap Locking Screws
1/2" NPT Threaded Hole
STEP 2: AIMING THE FIXTURE
1. Tilting: Loosen the joint screw and adjust the head of the xture to
the desired direction before retightening the screw.
2. Loosen the mounting knob and rotate the xture to the desired
position before retightening the knob.
Rotating
Joint Screw
Mounting Knob
Tilting

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. NOVEMBER, 2019
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTIONS
Adjustable Beam Wall Wash
5222
STEP 3: DIMMING ADJUSTMENT
1. Use a Philips head screwdriver to adjust the dimming dial.
2. Rotate until the arrow on the dial is pointed at the desired wattage.
The wattage may be adjusted to the pre-existing tabs or any value
in between.
3. The lower the wattage, the dimmer the xture will be.
4. Please refer to the yellow tag that is included in the packaging to
determine the size of the required transformer.
STEP 4: BEAM ANGLE ADJUSTMENT:
1. Note the three pre-determined beam angles on the beam angle
changing dial.
2. Use the provided Hex Key to slightly loosen the set screw one or
two turns. Do not remove set screw from the xture.
CAUTION: Do not remove set screw from the xture.
It should only be removed from the xture for servicing.
Consult factory for service instruction.
3. Hold the xture body and rotate the dial until the arrow is aligned
with the desired beam angle. This beam angle may be one of the
pre-determined markings or any number in between.
CAUTION: Keep the arrow marking on the xture body between
the beam angle range.
4. Tighten the set screw until it stops. Do not over tighten.
Set Screw
Beam Changing Dial
Beam Angle Markin
g
Fixture Body
Rotation
NEMA
4X3
NEMA
5X4
NEMA
6X5
4x3
(60
H x 35 V)
5x4
(90
H x 60 V)
6x5
(120
H x 90 V)
STEP 5: VERTICAL FIXTURE HEAD ROTATION ADJUSTMENT
1. Note the xture head can be rotated 90 degrees to achieve vertical
wall wash applications.
2. Hold xture body with one hand and rotate the xture head with
another hand to 90 degree.
3. Loose thumb screw and swap the horizontal shroud with a
vertical shroud.
NOTE: Vertical shroud is not provided (sold separately).
Rotation
NEMA
4X3
NEMA
5X4
NEMA
6X5
5x6
(90
H x 120 V)
3x4
(35
H x 60 V)
4x5
(60
H x 90 V)
*8
*15
*22
*24
Model: 5222
*Numbers not printed
*3

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. NOVEMBER, 2019
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTIONS
Adjustable Beam Wall Wash
5222
Fixture Head
Fixture Body
Horizontal Shroud
Thumb Screw
Vertical Shroud
(Not Provided)
ACCESSORIES
1. COLOR LENS:
Colored lenses come in red, blue, green, amber, frosted, and beam
spread to lter the light coming out of the xture.
Installation: Push the lens onto the center of the clip and push
them onto the front of the xture.
LENS-3X5-xxx
LENS CLIP
(Included in LENS-3x5-xxx)
ACCESSORIES
2. SURFACE MOUNT ACCESSORY:
The surface mount accessory is used to mount the xture to a hard
surface like wood or cement or as alternative to the mounting stake.
Installation: Mount the accessory to a hard surface using No. 10
Philips head screws that are at least half an inch long. If mounting
on concrete or a similar surface, rst use a plastic anchor sized
for No. 10 screws. If mounting on a soft surface rst attach the
included spikes.
Create a route underneath the accessory for your wire to travel
through. Lead your wire through the created route and screw your
xture onto the surface mount accessory.
Removable Spike
No. 10 Tapping Screw
Surface Mount Canopy

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. NOVEMBER, 2019
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTIONS
Adjustable Beam Wall Wash
5222
3. TREE MOUNT ACCESSORY:
The tree mount accessory is a way for xtures to be mounted on the
trunk or a branch of a tree while minimizing damage to the tree.
Installation with Wood Screw Bolt:
1. Mark the screw hole locations at the point of installation.
2. Thread one hex nut from the at side of wood screw bolt
until end of threaded.
3. Use a wrench to screw the bolt into the tree until
unthreaded portion of the bolt meets the surface of the
tree (Do this for all three bolts).
4. Place the tree mount junction box onto the bolts and
secure it using additional hex nuts.
5. Attach light xture and lead wire through the junction box.
Place all wire nuts into the tree mount junction box.
Installation with Wood Screw Bolt:
1. Mount the junction box mounting bracket onto the back of the
tree mount junction box with 4 screws (Leave the wood screw
bolts as they are not required for this installation).
2. Put the ratchet strap though the junction box mounting bracket
and tight the strap onto the tree.
3. Secure and tighten the strap by using the ratchet.
4. Attach light xture and lead wire through the junction box.
Place all wire nuts into the tree mount junction box.
Fixture
Hex Nut
Tree Mount Junction Box
Wood Screw
Tree
Fixture
5000-TCL
Tree Mount Junction Box
5000-TST
Junction Box
Mounting Bracket
5000-TST
Junction Box
Mounting Screw
Tree
5000-TST
Strap
5000-TST
Ratchet
NOTE: Due to tree growth, annual inspection of the strap is required to ensure that the xture is secure. Failure to do so may cause the
xture to fall from the tree, or damage to the xture or other items.