WAC Lighting Endurance WP-LED415 User manual

1WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. NOVEMBER, 2017
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
Single/Double Spot - Endurance
WP-LED415/WP-LED430
A1 B1
WARNING
IMPORTANT: NEVER attempt to do any work without shutting o the electricity.
1. Read all instructions before installing.
2. System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
3. Place the wall switch in the“OFF”position.
4. Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch“OFF”the circuit breaker switch(es) that control the power to the
space that you are working on.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out
or broken. Failure to follow this instruction may invalidate the ETL/cETL listing of this xture.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les règlements locaux.
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
- Toujours mettre le fusible ou le disjoncteur en position arrêt dans la pièce ou des travaux électriques sont prévus
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez
pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler
l’homologation ETL/cETL du luminaire.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e instalación de esta lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de alimentación principal
en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni utilice
piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación ETL/cETL esta lámpara.
Wire connector
7EAC112201
Qty: 3pcs
Junction box screw
7MPF0415C2
Qty: 2pcs + 1 extra

2WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. NOVEMBER, 2017
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION AND WIRING
STEP 1:
• Wrap locking nut with thread seal tape to act as a sealant.
• Mount xture housing onto the canopy plate.
• Tighten locking nut to secure xture position.
STEP 2:
• Connect the electrical wires as shown in Fig.1, making sure
that all wire connectors (A1) are secured. If your outlet box
has a green or bare copper ground wire, connect the xture’s
ground wire to it. After wires are connected, tuck them
carefully inside the junction box.
STEP 3:
• Mount xture housing onto the junction box with
junction box screw (B1).
• Tighten all conduit caps with thread seal tape.
Locking Nut
Fixture
Housing
Gasket
Junction Box
Junction Box Screw
B1
Wire Connector
A1
Conduit Caps
Canopy Plate
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Wiring
INSTALLATION INSTRUCTION
Single/Double Spot - Endurance
WP-LED415/WP-LED430

3WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. NOVEMBER, 2017
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
ADJUSTING THE LUMINAIRE:
• Vertical Adjustment: Loosen locking screw, rotate
xture to desired angle (±90°), and tighten locking screw.
• Rotation Adjustment: Loosen locking nut, rotate
xture to desired angle (360°), and tighten locking nut. Locking Nut
Locking Screw
Single Spot
WP-LED415
Double Spot
WP-LED430
Vertical
Adjustment
Rotation Adjustment
ENDURANCE SPOT MODELS
INSTALLATION INSTRUCTION
Single/Double Spot - Endurance
WP-LED415/WP-LED430

4WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. NOVEMBER, 2017
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
COMPLETING THE INSTALLATION
To prevent moisture from entering the outlet box and causing a short, use caulking (i.e.silicone sealant) to outline the outside of Spot junction
box where it meets the wall while leaving the bottom side unsealed to allow moisture to escape.
Note: Endurance Spot models are suitable for wet location installations in all mounting orientations.
COMPATIBLE DIMMERS
BRAND MODEL NUMBER TYPE
Lutron GRX-3103-A-G ELV 120V
Lutron RRD-6NA ELV 120V
Lutron DVELV-300P ELV 120V
Lutron SELV-300P ELV 120V
Please visit our website or contact a WAC Lighting professional for a complete list of compatible dimmers and sensors.
INSTALLATION INSTRUCTION
Single/Double Spot - Endurance
WP-LED415/WP-LED430