Wagan Elite 200W PRO User manual

Item No. 2600
Elite™200W PRO
DC to AC Pure Sine Inverter
User’s Manual

Elite™200W PRO by Wagan Tech®
1www.wagan.com
Thank you for purchasing the Wagan Tech®Elite™200W PRO Pure Sine Wave
DC to AC Power Inverter. Elite™200W PRO represents numerous improvements to
our standard pure sine that meet the needs of more demanding environments—
delivering clean quality power at an affordable price. It delivers a true sine
wave AC identical to that of commercial power. Use this inverter to power AC
appliances in your vehicle or off-grid backup power systems. Pure Sine Wave AC
means that your sensitive electronics, such as audio/video systems, computers,
and communications equipment will operate properly. Furthermore, appliances
with motors operate cooler, quieter, and more efficiently when they are powered
by sine wave AC.
This inverter is powered from 12 volts DC and it will continuously deliver 200
watts (400 watts momentary peak) AC power at 120 volts, 60 Hz. Superior
surge capability of 400 watts allows the inverter to start most difficult motorized
appliances. Advanced microprocessor-controlled circuits run cooler and are more
reliable than competing units. The DC terminals have been designed apart from
each other to ease installation and minimize the risk of accidental shortage when
handling the DC cables.
The Elite™200W PRO also operates at high efficiency (up to 90%), that results in
long run time and extended battery life compared to other inverters with this level
of power output. Neutral to ground bond, just like utility power.
A 2.1A USB Power Port provides a convenient way to power USB appliances or
charge smartphones, tablets and e-readers, and other mobile electronic devices.
This Inverter is supplied with a cord that connects the inverter to a DC power
supply.
The enclosure vents have been minimized to reduce the risk of pest intrusion in
arid tropical climates. This Wagan Elite™200W PRO Pure Sine Wave Inverter is
an indispensable addition to your compliment of mobile power equipment. With
minimal care and proper treatment, it will provide years of reliable service.
Read and understand this manual before installing and operating this inverter.
Keep this manual for future use.

©2013 Wagan Corporation. All Rights Reserved.
Wagan Tech and wagan.com are trademarks used by Wagan Corporation.
User’s Manual—Read before using this equipment
2
SPECIFICATIONS*
Output waveform Pure sine wave
Input 12V DC
Output 120V AC
TrueRated Power™ 200 watts
Peak surge 400 watts
Efficiency > 90%
Frequency 60Hz
Total harmonic distortion (THD) < 3%
No load current draw < 0.4A
Battery low alarm 10.5V ± 0.5V DC
Battery low shutdown 9.5V ± 0.5V DC
Over voltage shutdown 15.5V ± 0.5V DC
Cooling fan Thermally controlled
AC output sockets 2
USB power port 2.1A, 5V ± 0.25V
Power switch AC output ON/OFF control
Dimensions (body only) 6.2 in. × 4.1 in. × 2.0 in.
(15.8 cm × 10.5 cm × 5.2 cm)
Net weight (approximate) 1.5 lbs (0.7 kg)
*All specifications are typical at nominal line, half load, and 77ºF (25ºC) unless
otherwise noted. Specifications are subject to change without notice.

Elite™200W PRO by Wagan Tech®
3www.wagan.com
WARNING
INVERTER OUTPUT CAN BE LETHAL. IMPROPER USE OF THIS INVERTER MAY
RESULT IN PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
• Keep the inverter away from any direct heat source or combustible
materials.
• Keep well ventilated—this device generates heat.
• Keep this inverter in a dry environment.
• Do not operate any equipment over 200 watts.
• This inverter is designed to operate from a 12 volt DC power source only.
• Do not attempt to connect the inverter to any other power source, including
any AC power source.
• Incorrect battery polarity will damage the inverter and void the warranty.
• Do not open the inverter; there are no user serviceable parts inside.
• This inverter has an included 31.5 in. (80 cm) cable with 12V accessory
plug adapter.

©2013 Wagan Corporation. All Rights Reserved.
Wagan Tech and wagan.com are trademarks used by Wagan Corporation.
User’s Manual—Read before using this equipment
4
FRONT PANEL
AC Outlet
Power LED Fault LED On/Off Switch
AC Outlet
USB Power Port
• ON/OFF Switch — This switch controls AC output of the inverter.
• Operating LED (Green) — When this green LED is lit, the inverter is
operating normally.
• FAULT LED (Red) — The RED indicator turns on as the inverter shuts down
due to overheating, overload, under voltage, or over voltage.
• Immediately turn off all AC appliances if the FAULT LED is lit. Allow the
inverter to cool before continuing. Make sure that the ventilation vents
are not blocked.
• If an inverter shutdown was preceded by a buzzing sound, there
may be an excessive load in combination with a low voltage or cable
problem.
• AC Outlets — These outlets can supply up to 3.3 amps at 120V AC 60 Hz
• USB Power Port — This power port can supply 5 volts at 2.1A for charging
or powering smartphones, tablets and e-readers, MP3 players, GPS and
other small electronic devices.

Elite™200W PRO by Wagan Tech®
5www.wagan.com
• Audible Alarm (internal to the inverter) — When the Audible Alarm makes
a buzzing sound, the inverter senses a low battery condition. The user
should reduce the AC load, charge the battery, and check the DC cable for
excessive losses.
REAR PANEL
Cooling Fan
Negative (−)
Terminal
[Black]
Postive (+)
Terminal
[Red]
Fuse
• Positive Terminal — Positive (+) DC Input (Red)
• Negative Terminal — Negative (−) DC Input (Black)
• Cooling Fan — High-speed and load controlled
• Fuse — Replaceable external fuse
LOAD CONSIDERATIONS
The startup load of an appliance is a major factor of whether this inverter
can power it. This initial load is only momentary. With many appliances, it is
approximately twice the continuous load, but some appliance startup loads can
be as high as eight times the continuous load.

©2013 Wagan Corporation. All Rights Reserved.
Wagan Tech and wagan.com are trademarks used by Wagan Corporation.
User’s Manual—Read before using this equipment
6
To determine if an appliance or tool will operate with this inverter, first run a test.
The inverter will automatically shut down in the event of an output overload so
there is no danger of damaging either the inverter or the equipment. When the
red LED indicator is lit, the inverter is signaling a fault.
Maximum Power from Vehicular Accessory Sockets
Most vehicular accessory sockets that are controlled through a vehicle’s ignition
switch are fused at 15 amps. This limits inverter output to approximately 180
watts.
To Power 200 Watt Appliances:
1. For temporary use, connect a battery clip adapter cord (not included) to
the inverter and follow the procedure located under the “Connecting the
Inverter” section.
2. Install a separate fused DC accessory socket wired to the vehicle’s battery.
Fuse this circuit at 20 amps.
There is no danger in leaving the inverter directly wired to the battery if the
inverter is turned OFF after each use. The inverter will shut off when the vehicle’s
battery level drops down to 9.5 volts to protect the battery from draining
completely.
DETERMINING MAXIMUM APPLIANCE WATTAGE
Do not exceed the 200 watt maximum AC load or the inverter will shut down.
Most electrical tools, appliances, and audio/video equipment have labels that
list the unit’s power requirements in watts. If the tool or device is rated in amps,
multiply the amps by 120 (120V AC) to determine the watts. For example, an
appliance rated at 0.5 amps will draw 60 watts.
WATTS = VOLTS × AMPS
Remember to consider the startup surge that motorized appliances will cause. Do
not exceed the 400 watt momentary surge rating of this inverter. This can cause

Elite™200W PRO by Wagan Tech®
7www.wagan.com
immediate overload shut down and or blow a fuse. The fuse on this inverter is
external and replaceable for this purpose.
CONNECTING THE INVERTER
DC Plug Adapter Cord
1. Connect the red (+) and black (−) terminals of the supplied DC Plug Adapter
Cord to the red (+) and black (−) terminals on the rear of the inverter.
• Be sure to connect them into the correct polarity terminals on the rear
of the inverter. Reverse polarity connection will blow the fuse in the
inverter and can permanently damage to the inverter. Damage caused
by reverse polarity will void the warranty.
2. Connect the Plug end of the DC Adapter Cable into your vehicle’s 12V DC
accessory outlet. You may need to place the ignition switch to Accessory
Position if the vehicle engine is not operating.
3. Plug the AC appliance cord into the inverter’s AC receptacle, and/or your
USB appliance into the USB power port.
4. Place the ON/OFF power switch in the “ON” position. The green LED
should turn on, indicating the inverter is powered and operating normally.
5. When the inverter is not in use, place the inverter’s ON/OFF Power Switch
to the “OFF” position. We recommend also unplugging the DC Adapter
cable from the vehicle’s DC outlet.
OPERATING ISSUES: TELEVISION AND AUDIO
EQUIPMENT SUGGESTIONS.
Although all inverters are shielded and filtered to minimize signal interference,
some interference with your television picture may be unavoidable, especially
with weak signals. However, here are some suggestions that may improve
reception.

©2013 Wagan Corporation. All Rights Reserved.
Wagan Tech and wagan.com are trademarks used by Wagan Corporation.
User’s Manual—Read before using this equipment
8
• Make sure that the television antenna produces a clear signal under normal
operating conditions (i.e. plugged into a standard 110V/120V AC wall
outlet). Also ensure that the antenna cable is of good quality and properly
shielded.
• Sometimes vehicle alternators produce some electrical noise. There are
filters available to mount on the alternator to reduce the noise.
• Change the positions of the inverter, antenna cables, and television power
cord.
• Isolate the television, its power cord, and antenna cables from the 12
volt power source by running an extension cord from the inverter to the
television.
TROUBLESHOOTING
PROBLEM: Low or No Output Voltage – Fault LED Lit
Reason Solution
Poor contact with battery, inverter
terminals, or DC socket.
Clean terminals thoroughly. Reinstall
and tighten. Clean DC socket with non-
metallic abrasive emery stick.
PROBLEM: No Output Voltage – No LEDs Lit
Reason Solution
Blown fuse. Check vehicle’s Accessory Socket Fuse.
If the fuse is blown, replace with the
same type and rating fuse.

Elite™200W PRO by Wagan Tech®
9www.wagan.com
PROBLEM: Inverter Auto Shut Down – Fault LED Lit
Reason Solution
Battery voltage is below 9.5 volts. Charge or replace battery.
Inverter is too hot (thermal shut down
mode).
Allow inverter to cool.
Check for adequate ventilation.
Reduce the load on the inverter to
the specified TrueRated™power max
output.
PROBLEM: Inverter Shut Down – Fault LED Lit
Reason Solution
Equipment being operated draws too
much power.
Do not use the equipment with this
inverter; use a higher wattage inverter.
PROBLEM: Continuous Buzzing Sound
Reason Solution
Input voltage is below 10.5 volts . Keep input voltage above 10.5 volts .
Poor or weak battery condition. Recharge or replace battery.
Poor or loose cable connection. Inspect terminals and tighten all
connections.
Inadequate power being delivered to
the inverter or excessive voltage drop.
Use heavier gauge DC cables.
Keep cable length as short as possible.
DISPOSAL/RECYCLING OF INVERTER
Electronic products are known to contain materials that are toxic if improperly
disposed. Contact local authorities for disposal and recycling information.