WAGO I/O-SYSTEM 750 User manual

Fieldbus Independent
I/O Modules
24 V DC Bus Power Supply
750-613
Manual
Version 1.0.3

ii • General
WAGO-I/O-SYSTEM 750
I/O Modules
Copyright 2006 by WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [email protected]
Web: http://www.wago.com
Technical Support
Phone: [phone] – 5 55
Fax: [phone] – 85 55
E-Mail: [email protected]
Every conceivable measure has been taken to ensure the correctness and com-
pleteness of this documentation. However, as errors can never be fully ex-
cluded, we would appreciate any information or ideas at any time.
E-Mail: [email protected]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally trademark or patent protected.

Content •iii
WAGO-I/O-SYSTEM 750
I/O Modules
CONTENT
1Important Comments ................................................................................. 4
1.1 Legal Principles........................................................................................4
1.1.1 Copyright ............................................................................................. 4
1.1.2 Personnel Qualification ....................................................................... 4
1.1.3 Intended Use ........................................................................................ 4
1.2 Symbols .................................................................................................... 5
1.3 Number Notation...................................................................................... 5
1.4 Safety Notes ............................................................................................. 6
1.5 Scope ........................................................................................................ 6
2I/O Modules ................................................................................................. 7
2.1 System Modules ....................................................................................... 7
2.1.1 750-613 [24 V DC Bus Power Supply] ............................................... 7
2.1.1.1 View................................................................................................ 7
2.1.1.2 Description...................................................................................... 7
2.1.1.3 Display Elements ............................................................................ 8
2.1.1.4 Schematic Diagram......................................................................... 9
2.1.1.5 Technical Data .............................................................................. 10
2.1.1.6 Power supply concept ................................................................... 12

4 •Important Comments
Legal Principles
WAGO-I/O-SYSTEM 750
I/O Modules
1 Important Comments
To ensure fast installation and start-up of the units described in this manual,
we strongly recommend that the following information and explanations are
carefully read and abided by.
1.1 Legal Principles
1.1.1 Copyright
This manual is copyrighted, together with all figures and illustrations
contained therein. Any use of this manual which infringes the copyright
provisions stipulated herein, is not permitted. Reproduction, translation and
electronic and photo-technical archiving and amendments require the written
consent of WAGO Kontakttechnik GmbH & Co. KG. Non-observance will
entail the right of claims for damages.
WAGO Kontakttechnik GmbH & Co. KG reserves the right to perform
modifications allowed by technical progress. In case of grant of a patent or
legal protection of utility patents all rights are reserved by WAGO
Kontakttechnik GmbH & Co. KG. Products of other manufacturers are always
named without referring to patent rights. The existence of such rights can
therefore not be ruled out.
1.1.2 Personnel Qualification
The use of the product detailed in this manual is exclusively geared to
specialists having qualifications in PLC programming, electrical specialists or
persons instructed by electrical specialists who are also familiar with the valid
standards. WAGO Kontakttechnik GmbH & Co. KG declines all liability
resulting from improper action and damage to WAGO products and third party
products due to non-observance of the information contained in this manual.
1.1.3 Intended Use
For each individual application, the components supplied are to work with a
dedicated hardware and software configuration. Modifications are only
permitted within the framework of the possibilities documented in the
manuals. All other changes to the hardware and/or software and the non-
conforming use of the components entail the exclusion of liability on part of
WAGO Kontakttechnik GmbH & Co. KG.
Please direct any requirements pertaining to a modified and/or new hardware
or software configuration directly to WAGO Kontakttechnik GmbH & Co.
KG.

Important Comments •5
Symbols
WAGO-I/O-SYSTEM 750
I/O Modules
1.2 Symbols
Danger
Always abide by this information to protect persons from injury.
Warning
Always abide by this information to prevent damage to the device.
Attention
Marginal conditions must always be observed to ensure smooth operation.
ESD (Electrostatic Discharge)
Warning of damage to the components by electrostatic discharge. Observe
the precautionary measure for handling components at risk.
Note
Routines or advice for efficient use of the device and software optimization.
More information
References on additional literature, manuals, data sheets and INTERNET
pages
1.3 Number Notation
Number Code Example Note
Decimal 100 normal notation
Hexadecimal 0x64 C notation
Binary '100'
'0110.0100'
Within ',
Nibble separated with dots

6 •Important Comments
Safety Notes
WAGO-I/O-SYSTEM 750
I/O Modules
1.4 Safety Notes
Warning
Switch off the system prior to working on bus modules!
In the event of deformed contacts, the module in question is to be replaced, as
its functionality can no longer be ensured on a long-term basis.
The components are not resistant against materials having seeping and
insulating properties. Belonging to this group of materials is: e.g. aerosols,
silicones, triglycerides (found in some hand creams).
If it cannot be ruled out that these materials appear in the component
environment, then additional measures are to be taken:
- installation of the components into an appropriate enclosure
- handling of the components only with clean tools and materials.
Attention
Cleaning of soiled contacts may only be done with ethyl alcohol and leather
cloths. Thereby, the ESD information is to be regarded.
Do not use any contact spray. The spray may impair the functioning of the
contact area.
The WAGO-I/O-SYSTEM 750 and its components are an open system. It
must only be assembled in housings, cabinets or in electrical operation
rooms. Access must only be given via a key or tool to authorized qualified
personnel.
The relevant valid and applicable standards and guidelines concerning the
installation of switch boxes are to be observed.
ESD (Electrostatic Discharge)
The modules are equipped with electronic components that may be destroyed
by electrostatic discharge. When handling the modules, ensure that the
environment (persons, workplace and packing) is well grounded. Avoid
touching conductive components, e.g. gold contacts.
1.5 Scope
This manual describes the System Module 750-613 24 V DC Bus Power
Supply of the modular WAGO-I/O-SYSTEM 750.
Handling, assembly and start-up are described in the manual of the Fieldbus
Coupler. Therefore this documentation is valid only in the connection with the
appropriate manual.

750-613 [24 V DC Bus Power Supply] •7
View
WAGO-I/O-SYSTEM 750
I/O Modules
2 I/O Modules
2.1 System Modules
2.1.1 750-613 [24 V DC Bus Power Supply]
Internal System Supply Module DC 24 V
2.1.1.1 View
24V 0V
++
--
PE PE
13 14
C
D
B
A
750-613
Supply for system
24 V
0V
0V
Power jumper contacts
Status voltage supply
-Power jumper contacts
-System
Supply for
power jumper contacts
24 V
Data contacts
Fig. 2.1.1-1: Supply Module 750-613 g061300e
2.1.1.2 Description
The supply module 750-613 provides the internal system power to the
downstream modules and increases the system current supply by 2 A.
The system power supply is connected to the upper 24 V / 0 V terminals in
parallel to the coupler / controller.
Attention
Resetting the system by switching on and off the system supply must take
place simultaneously for all supply modules (coupler / controller and internal
system supply module 750-613)!
Furthermore the supply module 750-613 provides DC 24 V field side power to
the downstream modules.
The field power supply is derived from an external source via the lower 24 V,
0V and ground (earth) terminals.
Two green status LEDs indicate the 24 V voltage supply (system and field
power supply).

8 • 750-613 [24 V DC Bus Power Supply]
Display Elements
WAGO-I/O-SYSTEM 750
I/O Modules
Both the potential groups and the individual modules within these groups can
be arranged in any combination when designing the field bus node.
The supply voltage for the field side is made automatically through the
individual I/O modules by means of power jumper contacts.
Warning
The maximum current of the supply module is 10 A. When configuring the
system it is important not to exceed the maximum/sum current. However, if
such a case should occur, another supply module must be added.
The supply module 750-613 can be used with all couplers/controllers of the
WAGO-I/O-SYSTEM 750.
Attention
The supplementary power supply regulations (chapter 0, “
Power supply concept”) must be observed for the certified operation of the
supply module 750-613 in shipbuilding or offshore and onshore applications!
2.1.1.3 Display Elements
LED Designation State Function
off No DC 24 V system voltage
supply.
A
green
Status
voltage supply
–
System on DC 24 V system voltage supply.
off No DC 24 V voltage supply via
power jumper contacts.
B
or
C *)
green
Status voltage
supply
–
Power jumper
contacts. on DC 24 V voltage supply via power
jumper contacts.
13 14
C
D
B
A
A
B
Fig. 2.1.1-2: Display
Elements g062602x
or
Fig. 2.1.1-3: Display
Elements g062602x
*) LED position is manufacturing dependent

750-613 [24 V DC Bus Power Supply] •9
Schematic Diagram
WAGO-I/O-SYSTEM 750
I/O Modules
2.1.1.4 Schematic Diagram
Status
Status
DC
DC
I/O modules
0V
24V
24V
0V
0V
0V
24V
24V
1
2
3
4
5
6
7
8
750-613
Fig. 2.1.1-4: Supply Module 750-613 g061301e

10 • 750-613 [24 V DC Bus Power Supply]
Technical Data
WAGO-I/O-SYSTEM 750
I/O Modules
2.1.1.5 Technical Data
Module Specific Data
Voltage Supply DC 24 V (-25% ... +30%)
Input current max. 500 mA
Total current for I/O Modules 2000 mA
Voltage via power jumper contacts max. DC 24 V (-25% ... +30%)
Current via power jumper contacts max. 10 A
Dimensions W x H* x L
* from upper edge of 35 DIN rail
12 mm x 64 mm x 100 mm
Weight ca. 60 g
Standards and Regulations (cf. Chapter 2.2 of the Coupler/Controller Manual)
EMC-Immunity to interference (CE) acc. to EN 50082-2 (1996)
EMC-Emission of interference (CE) acc. to EN 50081-1 (1993)
EMC-Immunity to interference (Ship building) acc. to Germanischer Lloyd (97)
EMC-Emission of interference (Ship building) acc. to Germanischer Lloyd (97)
Approvals (cf. Chapter 2.2 of the Coupler/Controller Manual)
CULUS (UL508)
ABS (American Bureau of Shipping) 1)
BV (Bureau Veritas) 1)
DNV (Det Norske Veritas) 1) Cl. B
GL (Germanischer Lloyd) 1) Cat. A, B, C, D
KR (Korean Register of Shipping) 1)
LR (Lloyd's Register) 1) Env. 1, 2, 3, 4
NKK (Nippon Kaiji Kyokai)
RINA (Registro Italiano Navale) 1)
CULUS (UL1604) Class I Div2 ABCD T4A
KEMA II 3 G EEx nA II T4
Conformity Marking
1) Note information on “Voltage Supply“!