Wali GPV001 User manual

GPV001
WARNING
！！USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.
SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual.
Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect
assembly or inappropriate use.
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
12
Monitor Desk Stand
75x75\100x100
INSTALLATION MANUAL
1-844-SATTLER (18447288537)
[email protected]
www.walielectric.com
7kg/15.4lbs
RATED
MAX 32”
TIPOVER WARNING
● NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
● USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.
Supplied Parts List
Pole
A(x1)
Base
B(x1)
VESA Plate
C(x1)
Anti-skid Pad
F(x1)
Allen Key 4mm
G(x1)
Allen Key 6mm
H(x1)
Bolt
D(x1)
Bolt
E(x2)
M4x12 Bolt
M-A(x4)
M4x16 Bolt
M-B(x4)
M5x12 Bolt
M-C(x4)
M5x16 Bolt
M-D(x4)
D5 Washer
M-E(x4)
Spacer
M-F(x4)
Connect Pole Aand Base Busing Bolt Eand tighten with Allen Key 4mm G.
B
G
E
A
Tear off the protective paper to attach Anti-Skid Pad F to the bottom designated
position of Base Bas image shown.
B
F
3
Hand thread screws
into the threaded
inserts on the back of
your TV to determine
which screw diameter
(M4 or M5) to use.
M-C M-A
M-E M-E
C
M-E
M-F
M-B
M-D C
Step 3.1
Select TV Screws
Step 3.2
Select Spacers ( if needed )
Step 3.3a
Step 3.3b
Select M4x12 Bolt M-A or M5x12 Bolt M-C according to your TV/Monitor, connect
VESA Plate Etogether with D5 Washer M-E into the mounting holes on the back of
TV/Monitor, tighten with a screwdriver. (Screwdriver not included)
Select M4x16 Bolt M-B or M5x16 Bolt M-D according to your TV/Monitor, connect
VESA Plate Etogether with D5 Washer M-E and Spacer M-F into the mounting
holes on the back of TV/Monitor, tighten with a screwdriver. (Screwdriver not included)
Flat Back Monitor
Curved Back Monitor
M4 M5
C
C

5
4Put the assembled TV/ Monitor onto the Pole Aand tighten the VESA Plate with
Bolt Dfor stability.
Adjust the tilt angle using Allen Key 6mm H . 6Tear off the warning label from the gas spring button. Keep your hand pressing on the top of Pole A to
prevent it pop up. Open up the button and adjust the Pole A to the personal preferred height. Lock
the button and ensure stability. Suggest standing for easier adjustment.
WARNING!
D
A
WARNING!
H
8Manually swivel, tilt or rotate the monitor for the best viewing angle.
7Guide the cable through the clip holder and store the Allen Keys GHin the holder.
WARNING!
G
H
Caution: Keep your hand pressing on the Pole. Please do
not let go until the button is fully locked.
!A
A
+20°
-20°
± 45°
± 180°
min 13.8“- max 18.2”
min 13.8“- max 18.2”