Wali M001SXL User manual

M001SXL
WARNING
！
！
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.
SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual.
Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect
assembly or inappropriate use.
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
Single Monitor Desk Mount
75x75\100x100
200x100\200x200
INSTALLATION MANUAL
1-844-SATTLER (18447288537)
[email protected]
www.walielectric.com
(10kg/22lbs)
RATED
13-42”
TIPOVER WARNING
● NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
● USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.
Supplied Parts List
Pole
a (x1)
C-Clamp Brace
b1 (x1)
C-Clamp
b (x1)
Monitor Arm
a1 (x1)
M4x10 Bolt
e (x8)
Adapter
d (x2)
Adapter
c (x2)
M4 Washer
f (x8)
M4 Nut
g (x8)
Wrench
i (x1)
Support Plate
j (x1)
Spring Washer
k (x1)
M10 Washer
l (x1)
Grommet Base Plate
m (x1)
M8x12 Bolt
n1 (x2)
Wire Clip
n2 (x1)
Allen Key
o (x1)
M10 Bolt
p (x1)
M4x12 Bolt
q (x4)
M4 Spacer
s (x4)
M4x30 Bolt
r (x4)
M5x14 Bolt
h (x3)
Option A : Clamp Installation
1. Connect Pole a and C-Clamp Brace c from the bottom using M5x14 Bolt f and
tighten with Allen Key 3mm o .
1
2. Select the preferred height according to your desk thickness. Connect C-Clamp b to C-Clamp
Brace c using M8x12 Bolt g and tighten with Allen Key 5mm o . Rotate the hand knob
clockwise to fasten for stability.
Hand Knob
a
c
h
h
h
o
o
o
b
b
a
o
Option B : Grommet Base Installation
1. Place Pole a onto Grommet Base Plate m . Connect them from the bottom using
M5x14 Bolt and tighten with Allen Key 3mm .
o
o
a
a
m
m
h
b1
b1
b1
b1
n1
n1

ja
j
j
k
l
k
l
i
i
P
P
2a. Existing Grommet Hole Installation
If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before
installing the desk mount. Position the Pole a on the mounting surface and secure using the
Support Plate j , M10 Washer k , Spring Washer l , and M10 Bolt i . Fasten the Bolt using
the provided Wrench p .
2b. Self-drilled Grommet Hole Installation
Mark the position of the hole on your mounting surface. Drill a 3/8"(10mm) diameter hole at the
marked position through the mounting surface. Position the Pole a on the mounting surface and
secure using the Support Plate j , M10 Washer k , Spring Washer l , and M10 Bolt i . Fasten the
Bolt using the provided Wrench p .
jk
lp
a
a
jk
l
i
p
ø 10mm
(ø ")3/8
For Flat Back TV For Curved Back TV
Attach VESA Plate to the Mounting Hole of TV
2
For VESA 75x75mm and 100x100mm Mounting Holes
r
q
s
a1
a1
This way up!
This way up!
2 0mm
200mm
100mm
c
e
f
c
d
For VESA 100x200mm Mounting Holes
ca1
d
e
dc
c
d
d
c
f
g
s(if necessary)
rk
This way up!
j
j
k
l
i
a1
This w ay u p!
200mm
170mm
160mm
200mm
c
e
fg
c
c
cd
b
For VESA 200x200mm Mounting Holes
c
c
c
a1
d
d
d
de
c
r
fg
s(if necessary)
34
65
n2
a
a1
o
Put the Wire Clip 2 and Monitor Arm a through the Pole a , adjust the preferred height and
tighten using Allen Key 6mm o .
n2 a1
o
Adjust the tilt angle using Allen Key 5mm o .
Guide the cable through the Wire Clip n and store the Allen Keys o in the Wire Clip n .
o
o
a
o
o
n2
n2 n2 Manually swivel, tilt, and rotate the monitor for the best viewing angle.
+45°
-45°
a
i