Wali 2655LO User manual

Select Bolt M-A M-B M-C according to your TV, connect the assembled VESA Plate B with
Washer M-E and Spacer M-D / M-F into the mounting holes on the back of the TV, tighten with a
screwdriver.
Using M6 x 12 Bolt W-B and M6 Nut W-C to attach the Adapter C D to the
VESA Plate B and tighten with the provided Wrench F .
Full Motion TV Wall Mount
26”-55”
100x100\400x400
for VESA hole pattern:
100x100mm, 130x130mm
200x100mm, 200x200mm.
A
200mm
130mm
100mm
200mm
130mm
100mm
for VESA hole pattern:
200x300mm, 200x400mm
B
200mm
300mm
400mm
for VESA hole pattern:
400x200mm, 300x200mm
C
400mm
300mm
200mm
for VESA hole pattern:
400x300mm
D
400mm
300mm
for VESA hole pattern:
300x300mm, 400x400mm
E
400mm
300mm
400mm
300mm
C
D
B
C D
FB
F
W-C
W-B
Compatible VESA Patterns
Notice: If the adapter is not compatible with
your TV VESA Patterns, please loosen the
M6 x 12 Bolt W-B and M6 Nut W-C to
adjust the adapter. Retighten the Bolt and
Nut after the adjustment.
INSTALLATION MANUAL
1-844-SATTLER (18447288537)
[email protected]
www.walielectric.com
(45kg/99lbs)
RATED
Supplied Parts List
1A 1B
Model: 2655LO
Wall Plate & Articulating Arms
A (x1)
VESA Plate
B (x1)
Adapter
C (x2)
Adapter
D (x2)
M6 Nut
W-C (x8)
Anchor
W-D (x3)
Bubble Level
E (x1)
Wrench
F (x1)
M6 x 12 Bolt
W-B (x8)
6.3 x 60mm Screw
W-A
(x3)
M4 x 12mm Bolt
M-A (x4)
M8 x 25mm Bolt
M-C (x4)
M8 x 45mm Bolt
M-C (x4)
L5mm
Spacer
M-F (x8)
Ø6mm M4-5-6 Washer
M-E (x4)
L10mm
Spacer
M-D (x8)
M6 x 15mm Bolt
M-B (x4)
M6 x 30mm Bolt
M-B (x4)
M4 x 30mm Bolt
M-A (x4)
W-B/W-C
M-B M-C
M-A
M-C
M-F
B
M-D
W-C
M-E
M-F
W-B
W-C
W-B
M-E
M-D M-F
Tighten the screws on TV first, then
W-B and W-C.
M-B
WARNING
！
！
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.
SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual.
Do not exceed weight capacity. This product is designed to be installed on wood stud walls, solid concrete walls or brick
walls. Do not mount on drywall alone. We cannot be liable for damage or injury caused by improper mounting, incorrect
assembly or inappropriate use.
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
TIPOVER WARNING
M-A
W-C
W-B

±3°
-5°
10°
B
A
A
A
Install the Wall Plate to the Wall
1. If installing this product on a concrete wall, mark the position with Bubble Level E & pencil on the wall.
1. If installing this product on a wood stud, mark the position with Bubble Level E & pencil on the wall.
Loosen the Bolt as the image shown to adjust your TV to a horizontal level, retighten the Bolt with a screwdriver.
Loosen the Bolt as the image shown to adjust the VESA Plate B tilt angle using a screwdriver. (Tilt +10°/-5°)
Loosen the Bolt as the image shown to release the Bolt and Washer. Put the assembled TV/Monitor onto Arm A and ensure stability.
Tighten the VESA Plate B using the Bolt and Washer.
3. Insert the Anchor W-D into the mounting holes. Attach the Wall Plate & Articulating Arms A to the concrete
wall and tighten using Screw W-A .
3.Attach the Wall Plate & Articulating Arms A to the wood stud and tighten using Screw W-A .
2
34
B
A
E
EA
3
E
E
A
A
A
B
B
60 mm
Ø4 mm
Ø 4 mm
W-A
3
Ø 10 mm
60 mm
Ø 10 mm
X
W-A
W-D
W-A
W-D
W-D
W-A
W-D
W-A
W-A
2. Drill 0.16"(4mm) diameter x 2.36”(60mm) length holes at the marked position.
2. Drill 0.39"(10mm) diameter x 2.36"(60mm) length holes at the marked position.
Option A: Wood Stud
Option B: Brick /Concrete Wall