Walker Edison BR6DREBDR User manual

Assembly Instructions
P.1
V1 Revised 07/2022
Item # : BR6DREBDR
2018

P.2
and hammmer

Right side panel
Top panel
Back panel
Left foot
Left side panel
Bottom panel
1
2
3
4
5
6
7
01
01
01
01
02
02
02
Drawer bottom
Right drawer side
12
13
06
06
Drawer back
14 06
Crossbeam foot
Right foot
Drawer runner
8
9
02
12
Small drawer front
Drawer handle
Small drawer handle
Large drawer handle
15
16
17
18
02
04
02
02
Large Drawer Front
10 04
Leg crossbeam foot
19 02
Front crossbeam
20 04
Description QtyPart# Description QtyPart#
Left drawer side
11 06
Division
21 01
Parts List
4x
1
2
3
4
5
5
19
19
7
7
8
8
9
9
9
9
9
9
9
9
9
9
9
9
10
11
12
13
14
11
12
13
14
15
16
17
18
20
20
20
20 21
6
6
P.3
2x

Tape measure and hammer
recommended for assembly
(not included)
KWall anchor 01 pc
J1486mm “H” Profile 01 pc
LWasher 02 pc
MØ6mm 01 pc
A
B
C
D
E
F
Ø8*30mm Wood dowel 94 pcs
24 pcs
Screw 24 pcs
Ø3,5*30mm Screw 75 pcs
Ø4,0*40mm Screw 17 pcs
Ø10*10 Nail 36 pcs
Ø7*60mm Screw
4mm Hex Key
G04 pcs
H01 pcs
I Glue 01 pcs
Ø8*20mm Wood dowel
Ø3,5*25mm
NScrew 20 pcs
Ø4,5*25mm
P.4
Hardware List

Step 1
A
A
AØ8*30mm 70
I01
Insert wood dowel (A) and glue (I)
into parts (2, 3, 5, 12, 13, 16, 17, 19, 20, 21).
Insert wood dowel (B) and glue (I)
into part (9).
BØ8*20mm 24
Please assemble on
a clean soft surface
to avoid damage.
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
A
A
A
A
2
3
21
20
19
5
9
12
11
6x
6x
2x
2x
12x
4x
P.5

Step 2
Step 3
D
Ø3,5*30mm 04
Attach part (20) to parts (3,21)using screw (D)
D
D
D
D
D
3
21
20
20
20
D
D
20
2
21
Attach part (20) to parts (21,2)using screw (D)
P.6
D
Ø3,5*30mm 04
D
D
D

Step 4
Step 5
E
E
E
E
E
E
E
E
E
4
D
D
D
5
8
6
P.7
2x
Use screw (D) to attach part (5) to part (6,8)
Attach part (4) to boby with screws (E)
E
Ø4,0*40mm 09
D
Ø3,5*30mm 04

Step 6
Step 7
H
G
Ø7*60mm
4mm
G04
H01
EØ4,0*40mm 02
E
G+H
G+H
E
6
6
8
8
D
E
E
ED
D
E
E
D
E
19
19
D
E
Use screw (E) to attach legs to body with screws (E)
and use screw (G) and hex key (H) to attach the feet
to the body.
Attach cross beam (19) to body using screw (D, E)
19
P.8
E
Ø4,0*40mm 06
D
Ø3,5*30mm 04

Step 8
Step 9
D
J
FØ10*10 36
J01
1486mm
7
7
760mm
D
D
D
D
D
D
D
1
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
FF
F
FF
F
FF
F
FF
J
7
7
Use screw (D) to attach
part (1) to body
Secure back panel (7) with part (J) to body with nails (F)
P.9
D
Ø3,5*30mm 09

Step 10
Step 11
FRONT
2
C
A
A
A
A
A
A
A
A
A
A
A
A
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
9
9
9
9
9
9
9
9
9
9
9
9
C
9
Use screw (C) attach parts (9) to BOTH sides of part
(2,3,21)
NOTE: The extra holes in part (9) should face the top of
part (21)
Insert wood dowel (A) into the front hole
in the drawer rails (9)
A
FRONT
P.10
3
21
Ø3,5*25mm 24
AØ8*30mm 12