Walker Edison BTOD User manual

ITEM#: BTOD
Assembly Instructions
  
 
Revised 03/2017
Copyright © 2009, by Walker Edison Furniture Co., LLC. All rights reserved. P.1

Instruction Manual
IMPORTANT INFORMATION
READ BEFORE ASSEMBLING THIS PRODUCT
Follow the information on the warning labels found on the bunk bed and on the packaging. Do not
remove the warning labels from the bed.
Use only a mattress with the dimensions 74-75 in.L x 37.5-38.5 in.W x 9 in.H on the upper bunk.
The surface of the mattress must be at least 5 in. (127mm) below the upper edge of the guardrails.
Mattress must not exceed the maximum thickness of 9 in.
Always use the recommended size of mattress or mattress support, or both, to help prevent the
likelihood of entrapment or falls.
The use of a water or sleep flotation mattress is prohibited.
Replacement parts, including additional guardrails, may be obtained from any of Walker Edison
Furniture Company’s dealers or by contacting us online at www.walkeredison.com.
DO NOT use substitute parts. Contact the manufacturer or dealer for replacement parts.
Always use guardrails on the upper bunk. If the bunk bed will by placed next to a wall, the guardrail
running the full length of the bed should by placed against the wall to prevent entrapment between
the bed and the wall.
Periodically check that the guardrails, ladders and other components of the bed are in their proper
position, free from damage and that all connectors are tight.
Always use the ladder to access the upper bunk.
DO NOT allow children under 6 years of age to use the upper bunk.
DO NOT allow horseplay on or under the bed. Prohibit jumping on the bed.
Prohibit more than one person on the upper bunk.
The use of a night light may provide an added safety precaution for a child using the upper bunk.
STRANGULATION HAZARD – Never attach or hang items to any part of the bunk bed that are not
designed for use with the bed; including but not limited to hooks, belts and jump ropes.
Keep these instructions for future reference.

Slide curved post sections (C,K) and curved post sections (D,L) onto post sections (E).
Secure the post sections together using medium bolts (1) with small washers (5). Tighten
medium bolts (1) with small wrench (11).
Screw double-sided screws (6) into post (A). Attach guardrail (P) to post (A) and curved post section (C) using
medium bolts (1) with small washers (5). Attach crossbar (H) to post (A) and curved post section (K) using
medium bolts (1) with small washers (5). Tighten medium bolts (1) with small wrench (11). Repeat this step with
post (B) and curved post sections (D,L) on the opposite side of the bunk bed.

Slide washers (8) onto double-sided screws (6). Screw ladder rungs (M) onto double-sided
screws (6). Attach ladder rail (S) to ladder rungs (M) using bolts (7) with washers (8). Tighten
bolts (7) with small wrench (11). Repeat this step on the opposite side of the bunk bed.
Secure ladder rail (S) to guardrail (P) using medium bolt (1) with small washer (5). Secure
ladder rail (S) to crossbar (H) using large bolt (3) with large washer (4). Tighten bolts with
wrenches (11,12). Repeat this step on the opposite side of the bunk bed.

Attach support legs (Q) to support bars (I) using small bolts (2) with small washers (5). Tighten
small bolts (2) with small wrench (11).
Attach support leg (N) to crossbar (G) using medium bolts (1) with small washers (5). Tighten
medium bolts (1) with small wrench (11). Repeat this step for second crossbar (G).

Attach crossbars (F,G) to post (B) and to curved post sections (D,L) using medium bolts (1)
with small washers(5). Tighten medium bolts (1) with small wrench (11).

Attach crossbars (F,G) to post (A) and to curved post sections (C,K) using medium bolts (1)
with small washers(5). Tighten medium bolts (1) with small wrench (11). Ensure that the
Manufacturer and Safety Labels are positioned as shown above.

Attach support bars (I) to crossbars (H) using medium bolts (1) with small washers (5). Tighten
medium bolts (1)with small wrench (11).

Insert mattress support bars (O) into the slots of crossbars (F). Insert mattress support bars
(R) into the slots of crossbars (G). Secure mattress support bars (O,R) by snapping plastic tab
locks (9) into the slots of crossbars (F,G). It may be necessary to apply more pressure to some
plastic tab locks than others. Snap plastic links (10) onto mattress support bars (O,R).

Attach guardrail (J) to the back of the bunk bed using medium bolts (1) with small washers (5)
at posts (A,B), and large bolts (3) with large washers (4) at crossbar (F). Tighten all bolts with
wrenches (11,12).