Walker Edison BWTOTCOT User manual

P.1
Item #:
BWTOTCOT
09/2018
2018

7.5 in. H on the upper
7 in.

Parts List
P.3
03
05
02
01
10
11
04
05
11
10
15
15
08
07
09
06
07
06
14
13
12
01
04

P.4
Hardware List
Ref.
A
B
C
D
E
04
19
35
02
16
16
F
G
H
K
01
14
64
14x60mm
10x40mm
Hex Key
Qty.
7x100mm
1/4x110mm
1/4
7x50mm
4x35mm
62mm Spacer
Hammer required for assembly

Step 1
Step 2
A
08
09
07
06
2x
2x
2x
2x
35x
10
11
01
02
03
04
05
10
11
10
01
05
04
11
16x
C
c
c
c
c
c
cc
c
c
c
c
c
c
c
c
c
1x
F
C
F
4x 12
Insert wood dowels (A) into guardrails (6, 7, 8, 9, 10, 11,12).
Attach posts(1) and(2) to grid(10) using wood joint connectors (C).
Attach posts(3) and(1) to grid(10) using wood joint connectors (C).
Attach posts(4) and(5) to grid(1) using wood joint connectors (C). 2x
This up Arrow

Step 3
Step 4
P.6
GF
G
G
G
G
8x
G
1x
F
14
12
13
G
G
GG
D
F
8x
D
E
8x
E
D
D
D
D
06
07
11
11
05
04
05
04
1x
F
Attach ladder rungs (12) to ladder legs (13, 14) using wood joint
connectors (G).
Insert barrel nut (E) into pre-drilled holes on guardrails (6, 7). Attach
guardrails (6, 7) to end rails (11) using wood joint connector (D). Wood
joint connector (D) will screw into barrel nut (E).

Step 5
P.7
Step 6
D
F
D
C
D
C
E
C
D
D
06
09
08
07
10
01
03
02
01
10
C
8x
D
8x
E
3x
C
4x
B
8x
H
B
H
11
11
10
10
1x
F
H
1st
2nd
Insert barrel nut (E) into pre-drilled holes on guardrails (6, 7). Attach
guardrails (6, 7, 8, 9) to end rails (10) using wood joint connector (C)and
Wood joint connector (D) will screw into barrel nut (E).
Insert wood dowels (B) into pre-drilled holes on end rail (11) posts.
Carefully lift and place the upper bunk assembly onto the lower bunk
assembly using wood dowels (B) as guides. Once in place, secure the
upper and lower assemblies using wood joint connectors H).

P.8
Step 7
6x
G
G
G
G
G
G
56x
H
2x
15
H
HH
K
K
19
19
G
F
1x
F
Attach ladder to upper and lower bunk assembly using wood joint
connectors (G).
Attach wood slat (15) to guardrails on upper and lower bunk assembly
using wood joint connector (H). Use wood spacer (K) to ensure proper
spacing.
62mm Spacer
2x
K
Step 8

P.9
Step 1
Step 2
Disassembly Instructions
Undo steps 6 and 7 of this instruction set.
Place the separate beds on the floor as pictured.
F
Remove the parts indicated by the arrow.

P.10
Step 3
Step 4
Reverse the parts according to the image.
Reassemble the parts.
Congratulations! This bunk was transformed into two beds with
headboards and footboards.
F