WALKY WL1024 Technical specifications

EN - Instructions and warnings for installation and use
IT - Istruzioni ed avvertenze per linstallazione e luso
FR - Instructions et avertissements pour linstallation et lutilisation
ES - Instrucciones y advertencias para la instalación y el uso
DE - Installierungs-und Gebrauchsanleitungen und Hinweise
PL - Instrukcje i ostrzeżenia do instalacji i użytkowania
NL - Aanwijzingen en aanbevelingen voor installatie en gebruik
WALKY
WL1024
WL1024C
Swing gate opener

EN
English – 1
ENGLISH
Contents
1 - WARNINGS AND GENERAL PRECAUTIONS . . . . . . . . . . . . . . . . . . . . 1
1.1 - Safety warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 - Warnings for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.3 - Warnings for use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2 - PRODUCT DESCRIPTION AND INTENDED USE . . . . . . . . . . . . . . . . . 1
3 - INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
3.1 - Pre-installation checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
3.2 - Usage limitation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
3.3 - Preparatory work prior to installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.4 - Installation of the gearmotor mod. WL1024C - WL1024 . . . . . . . . . . . . 3
3.4.1 - Establishing the length of the gearmotor arm . . . . . . . . . . . . . . 3
3.4.2 - Installation of a gearmotor with a STANDARD LENGTH ARM . . 3
3.4.3 - Installation of a gearmotor with a SHORTENED ARM . . . . . . . . 4
3.5 - Installation of the multi-purpose lamp mod. WLT on the gearmotor
model WL1024C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.6 - How to remove the control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.7 - Adjusting the alignment of the gate leaves when closed . . . . . . . . . . . . 5
3.8 - Securing and releasing the gearmotor manually . . . . . . . . . . . . . . . . . . 5
4 - ELECTRICAL CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4.1 - Description of the electrical connections . . . . . . . . . . . . . . . . . . . . . . . . 5
4.2 - Connecting the power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.3 - Connecting the gearmotor without a control unit mod. WL1024 . . . . . . 5
4.4 - Connecting other devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4.5 - Addressing the connected devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.6 - Initialisation and connection check . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.7 - Recognition of the connected devices . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.8 - Recognition of the positions of the mechanical stops . . . . . . . . . . . . . . 6
4.9 - Gate leaves motion check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5 - TESTING AND COMMISSIONING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5.1 - Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5.2 - Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
6 - PROGRAMMING THE CONTROL UNIT . . . . . . . . . . . . . . . . . . . . . . . . 7
6.1 - Level one programming (ON-OFF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
6.2 - Level two programming (adjustable parameters) . . . . . . . . . . . . . . . . . . 8
6.3 - Memory deletion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6.4 - Special functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
7 - WHAT TO DO IF... (troubleshooting guide) . . . . . . . . . . . . . . . . . . . . . . 9
8 - FURTHER INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
8.1 - Connection of the OXI radio receiver . . . . . . . . . . . . . . . . . . . . . . . . . . 10
8.2 - Connection and installation of the back-up battery mod. PS424 . . . . . 10
8.3 - Connection of the Oview programmer . . . . . . . . . . . . . . . . . . . . . . . . 10
8.4 - Connection of the Solemyo solar power system . . . . . . . . . . . . . . . . . 10
9 - PRODUCT MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
DISPOSING OF THE PRODUCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
PRODUCT TECHNICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . 11
Product life span . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
EC DECLARATION OF CONFORMITY . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
APPENDIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I
Instructions and warnings for the user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . III
Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X
1.1 - Safety warnings
• IMPORTANT! – This manual contains important instructions and warn-
ings regarding safety. Incorrect installation may cause serious injury. Before
commencing work, all sections of the manual must be read carefully. If in any
doubt, suspend installation and call the Nice Support Service for clarification.
• IMPORTANT! – This manual contains important instructions. Keep it for
future maintenance work and disposal of the product.
• IMPORTANT! – Under the latest European legislation, automatic door
and gate installations must be compliant with the standards specified in
Directive 2006/42/EC (formerly 98/37/EC) (the Machinery Directive) and
the standards EN 12445, EN 12453, EN 12635 and EN 13241-1 in partic-
ular, which enable conformity of the automated functionality to be de-
clared. In the light of the above, all work involving installation, con-
nection, testing and maintenance of the product must be carried out
exclusively by qualified and competent technicians!
1.2 - Warnings for installation
• Before commencing the installation, check if the product is suitable for the
desired type of use (see “Usage limitation” paragraph 3.2 and the "Product
technical specifications”). If it is not suitable, DO NOT continue with the instal-
lation.
•All installation and maintenance work must be carried out with the au-
tomation system disconnected from the electricity supply. If the power
disconnection device cannot be seen from where the automation system is
positioned, then before starting work a notice must be attached to the dis-
connection device bearing the words “CAUTION! MAINTENANCE IN PRO-
GRESS”.
• The Control unit must be connected to an electricity supply line equipped
with protective earthing.
• Handle the product with care during installation, taking care to avoid crush-
ing, denting or dropping it, or contact with liquids of any kind. Keep the prod-
uct away from sources of heat and naked flames. Failure to observe the
above can damage the product, and increase the risk of danger or malfunc-
tion. Should this occur, suspend installation work immediately and contact
the Nice Support Service.
• Do not modify any part of the product. Prohibited modifications can only lead
to malfunctions. The manufacturer declines all responsibility for damage re-
sulting from unauthorized changes made to the product.
• If the gate or door being automated has a pedestrian gate, then the system
must include a control device that will inhibit the operation of the motor when
the pedestrian gate is open.
• The products packaging material must be disposed of in full compliance with
local regulations.
1.3 - Warnings for use
• The product is not intended for use by persons, including children, with limit-
ed physical, sensory or mental capacities, or who lack experience or knowl-
edge, unless supervised or trained in the use of the product by a person
responsible for their safety.
• Any children near the automation system must be kept under supervision to
ensure that they do not play with it.
• Do not allow children to play with the fixed control devices. Keep remote con-
trol devices out of the reach of children.
WARNINGS AND GENERAL PRECAUTIONS
1
The devices comprising this product are designed to automate a gate or door
with one or two leaves. IMPORTANT! – Any other use apart from that
described herein, including in different environmental conditions from
those described in this manual is to be considered improper use and is
not permitted!
The principal component of the automation system comprises one or two elec-
tric gearmotors (according to the number of leaves to be automated), each
equipped with a direct current motor and epicyclic reduction gear. One of the
gearmotors (mod. WL1024C) has a control unit that controls its operation. The
Control unit consists of a board with a radio receiver for receiving the com-
mands sent by the transmitter.
The control unit is designed for connection to several devices belonging to the
Opera system, the Bluebus system and the Solemyo solar powered system.
If it is mains powered, it can house a back-up battery (mod. PS424, optional
accessory) which in the event of a power cut (electricity black-out) guarantees
that the automated device will perform certain manoeuvres in the hours that fol-
low.
In the event of a power cut, the gate leaves can be moved by releasing the
gearmotor with the dedicated key; to perform the manoeuvre manually please
see chapter 3.8.
PRODUCT DESCRIPTION AND
INTENDED USE
2

EN
2– English
3.1 - Pre-installation checks
Before going ahead with the installation, check the integrity of the product com-
ponents, and ensure the model chosen is suitable for its intended use and for
the environment in which it is to be installed.
• Check that all the material to be used is in excellent condition and suitable for
its intended use.
• Check that the ground-mounted mechanical stops are present both when
opening and closing the automation system.
• Check that the mechanical structure of the gate is suitable for the installation
of automation and compliant with locally applicable regulations (if necessary,
refer to the label on the gate). This product cannot be used to automate a
gate which is not already in good, safe working order, neither can it fix faults
caused by incorrect installation or poor maintenance of the gate.
• Check that the operating conditions of the devices are compatible with the
usage limitation declared (see paragraph 3.2).
• Move the gate leaves manually in both directions and ensure that the resist-
ance to movement is constant at all points of travel (there should not be any
points where more force or less is required).
• Bring the gate leaves manually into a position at random, then let go and
check that they remain stationary.
• Check that the gearmotor fixing zone is compatible with its overall dimen-
sions (fig. 1).
• Check that the place where the gearmotor is to be installed allows enough
space for its arm to execute its full range of movement.
• Check that there is sufficient room around the gearmotor for it to be released
manually when required.
• Ensure that the surfaces on which the various devices are to be installed are
strong and capable of ensuring a firm hold.
• Ensure that each device is installed in a position which is protected and does
not expose it to accidental impacts.
• Ensure that all the electrical cables to be used are the type listed in Table 1.
3.2 - Usage limitation
Before installing the gearmotor, check that its data complies with the usage lim-
itation specified below and falls within the limits stated in the chapter entitled
“Product technical specifications”:
With FULL LENGTH motor arm (as shipped from the factory):
- maximum width of leaf: 1.60 m (= maximum weight of leaf: 110 kg)
- maximum height of leaf: 2 m
With SHORTENED motor arm (cut by the installer):
- maximum width of leaf: 1.60 m (= maximum weight of leaf: 100 kg)
- maximum height of leaf: 2 m
•Check to run: apply to Graph 1 the weight and width of the leaf; plot two lines
from these points and check that they intersect in one of the two grey areas of
the graph. Important! - If the lines cross in the white area, this product cannot
be used to automate this particular gate.
•To enable the installation of the gearmotor, the minimum width of the column
should be 80 mm.
•The gearmotor arm must be positioned in the upper part of the gate leaf.
IMPORTANT! - The gearmotor must not be mounted upside down, i.e. with
the arm pointing downwards.
•The arms fastening bracket must be fitted at one of the strongest parts of the
leaf (e.g. the frame), in order to ensure a firm and safe hold;
•Check distance “E” (fig. 7):
- If distance “E”falls in the range 80 mm (minimum) to 299 mm (maximum),
the gearmotor arm will need to be shortened. In such conditions, the leaf will
be able to open by up to 90°.
- If distance “E”is 300 mm or more, there is no need to shorten the gear-
motor arm. In such conditions, the leaf will be able to open by up to 110°.
3.3 - Preparatory work prior to installation
Fig. 2 illustrates an example of an automated system, achieved using Nice
components:
a- Gearmotor with control unit mod. WL1024C
b- Gearmotor without control unit mod. WL1024
c- Multi-purpose lamp mod. WLT (to be installed on the gearmotor with con-
trol unit mod. WL1024C); see chapter 3.5 and the lamps own instruction
manual
d- Pair of photocells mod. MOFB
e- Digital keyboard (mod. MOTB) - Transponder reader (mod. MOMB) - Key
selector (mod. MOSE)
f- Pair of photocell posts
g- Opening and Closing mechanical stops
h- Electrical lock
These components are positioned according to a typical standard layout.
Referring to fig. 2, establish the approximate position in which to install each
component required for the system. Important – Before commencing installa-
tion, prepare the electrical cables necessary for your system, referring to fig. 2a
and to “Table 1 - Technical characteristics of the electrical cables”.
Important – While laying the tubes for the electrical cables, consider that due
to the possible build-up of water in the aqueducts, the connection tubes could
cause condensation to form inside the control unit and damage the electronic
circuits.
INSTALLATION
3
Connection Type of cable Maximum permitted length
A:POWER cable One 3 x 1.5 mm2cable 30 m (note 1)
B:ELECTRICAL LOCK cable One 2 x 1 mm2cable 6 m
C:BLUEBUS DEVICES cable One 2 x 0.5 mm2cable 20 m (note 2)
D:KEY SELECTOR cable Two 2 x 0.5 mm2 cable (note 3) 50 m
E:GEARMOTOR POWER cable One 3 x 1.5 mm2cable 6 m
EXTERNAL AERIAL cable (optional) One type RG58 screened cable 20 m (recommended less than 5 m)
Note 1 – If the power cable is more than 30 m long, you will need to use a cable with a wider cross-section (3 x 2.5 mm2) and you will have to install protec-
tive earthing near the automation system.
Note 2 – If the Bluebus cable is more than 20 m long, and up to a maximum of 40 m long, you will need to use a cable with a wider cross-section (2 x 1 mm2).
Note 3 – These 2 cables can be replaced with 1 single 4 x 0.5 mm2 cable.
IMPORTANT! – The cables used must be suitable for the type of environment where they are installed.
TABLE 1 - Technical characteristics of the electrical cables
GRAPH 1
For full length
arm
For shortened
arm
WIDTH (m.)
WEIGHT (kg.)
Other available accessories include the receivers designed with “SM” connec-
tors (SMXI, OXI, etc.).
The gearmotor with control unit (mod. WL1024C) is designed to accommodate
the installation of the multi-purpose lamp mod. WLT (see chapter 3.5), which
can operate as a flashing emergency light or courtesy light, depending on the
control unit programming. In addition, it can be used as a twilight by activating
a built-in light sensor; please refer to the relevant instruction manual for specifi-
cations.

EN
English – 3
3.4 - Installation of the gearmotor mod. WL1024C - WL1024
WARNINGS
• Failure to install correctly can cause serious injury to the person carry-
ing out the work and those using the system.
• Before starting to assemble the automation system, carry out the pre-
liminary checks described in paragraphs 3.1 and 3.2.
• The gearmotor arm can be shortened from the standard length provid-
ed. It needs to be reduced in length if there is a fixed obstacle close to
the gearmotor (such as a wall or post) impeding the full range of move-
ment of the arm. In order to establish whether the arm needs to be
shortened,it is therefore necessary to follow the procedure in 3.4.1
before starting the installation.
Assemble the component parts of the motor arm, referring to fig. 3. Do not
insert the Benzing retaining ring at this stage (fig. 4). N.B.! - The curved arm
must be positioned with the curved part towards the gate leaf, as shown
in fig. 5.
3.4.1 - Establishing the length of the gearmotor arm
01. Determine the VERTICAL position of the gearmotor: draw a horizontal
line on the column at the same height at which the fastening bracket for
the arm will be located on the leaf once the installation is complete.
02. Determine the HORIZONTAL position of the gearmotor:
a) Determine the maximum opening position of the leaf:determine the
maximum opening angle (maximum 110°).
b) Measure distance B and determine distance A:
1 - Measure distance B on the column (fig. 5). This is the distance
between the fulcrum of rotation of the gate leaf and the surface of the col-
umn where the rear bracket of the gearmotor will be fixed.
2 - On Graph 2A, mark distance B, as just measured, and trace a vertical
line from this point until it intersects with the area which includes the angle
value measured in point a.
3 - At the points where the vertical line intersects with the area, trace hori-
zontal lines across column “A”, to determine the values which can be used
for distance A. Then choose a value for A from this range, one of the
smaller values if possible.
4 - Mark distance A on the column and trace a vertical line corresponding
to it (fig. 6).
5 - If there is a wall or other immovable obstacle near the vertical line,
measure the distance between this line and the obstacle (fig. 7): this is
distance E.
IMPORTANT!
• If distance E falls in the range 80 mm (minimum) to 299 mm (maxi-
mum), continue the installation with procedure 3.4.3.
• If distance E is 300 mm or more, continue the installation with pro-
cedure 3.4.2.
5 - Release the gearmotor with the dedicated key (see chapter 3.8).
3.4.2 - Installation of a gearmotor with a STANDARD LENGTH ARM
Important! - This part of the installation can only be carried out after 3.4.1
has been completed.
01. Affix the gearmotor to the column (fig. 9):
a) Hold the gearmotor against the column(*) so that its vertical centre line
corresponds with the vertical line traced earlier (distance A), and its arm
corresponds with the horizontal line traced during procedure 3.4.1. Now
ensure that the gearmotor is completely levelled: if off-axis, it can cause the
automation to malfunction.
(*) Note - If the column surface is between 80 and 135 mm wide, then
before continuing with the installation, the gearmotors rear fastening brack-
et will need to be rotated by 90°. To rotate the bracket, refer to fig. 8.
b) Mark the fastening points, drill the required holes in the surface of the
column and insert the plugs; now fix the gearmotor in place using suitable
screws and washers.
02. Affix the gearmotor arm to the gate leaf (fig. 9):
a) Bring the gate leaf into the fully Closed position;
b) Open out the gearmotor arm to its maximum extension;
c) Bring the arm up to the gate leaf and hold the fastening bracket against
the leaf.
d) Ensure that the gearmotor arm is levelled properly, and use a pencil to
mark the centre of the slot profile on the bracket, to enable fine adjust-
ments to be made to the closure alignment of the leaf in future (see para-
graph 3.7).
e) Holding the bracket against the gate leaf with one hand, attempt to open
and close the gate completely, up to the respective mechanical stops.
Important! - If the movement of the arm is hampered during the test
by a wall or other fixed object, stop working on this procedure and go
to procedure 3.4.3.
f) Drill holes in the gate leaf at the points marked and remove the bracket
from the arm and affix it to the gate leaf with suitable screws.
g) Attach the arm to the bracket, inserting the pin and the Benzing retaining
ring. Important - Check that the bracket and the arm are completely level.
Loosen the screws of the bracket and adjust as required to ensure level.
h) Fix the end stops to the ground permanently, in the position determined
at the start of the procedure. Important! - Check that the gate leaf closes
completely against the end stop. To make fine adjustments to the closure
alignment, refer to paragraph 3.7.
i) Finally, bring the leaf manually to around its midpoint of travel and secure
the gearmotor using the dedicated key (see chapter 3.8). Then manually
open the leaf by a few more centimetres.
03. If the gate being automated has two leaves, then to install the other gear-
motor repeat all the actions described here in chapter 3.4.
GRAPH 2A

EN
4– English
3.4.3 - Installation of a gearmotor with a SHORTENED ARM
Important! - This part of the installation can only be carried out after 3.4.1
has been completed.
01. Determine a new maximum opening angle for the gate leaf (max 90°):
ignoring the maximum opening position established for the leaf during pro-
cedure 3.4.1, bring the leaf to a new maximum opening position, ensuring
that the angle does not exceed 90°. Then hold the gate leaf provisionally in
this position using a ground-mounted stop.
02. Determine distances A - B - C:
a) Measure distance B (fig. 10) on the column. This is the distance
between the fulcrum of rotation of the gate leaf and the surface of the col-
umn where the rear bracket of the gearmotor will be fixed.
b) On Graph 2B, mark distance B as measured, and trace a vertical line
from this point.
c) On the column, determine the value for distance A, at which to mount
the rear bracket of the gearmotor (refer to fig. 11). N.B.! - Choose a value
for A, the smaller the better, in order to keep the motor free of the
obstacle.
d) On Graph 2B, mark distance A as just measured and plot a horizontal
line from this point until it intersects with the vertical line traced earlier. The
meeting point of these lines defines distance C, i.e. the distance required
between the two pins on the slotted arm (fig. 12). Example from graph 2B:
if the value of Bis 105 mm and Ais 143 mm, then point Cis 182.
03. Affix the gearmotor to the column (fig. 13):
a) Hold the gearmotor against the column (*) so that its vertical centre line
corresponds with the vertical line traced earlier (distance A), and its arm
corresponds with the horizontal line traced during procedure 3.4.1. Now
ensure that the gearmotor is completely levelled: if off-axis, it can cause the
automation to malfunction.
(*) Note - If the column surface is between 80 and 135 mm wide, then
before continuing with the installation, the gearmotors rear fastening brack-
et will need to be rotated by 90°. To rotate the bracket, refer to fig. 8.
b) Mark the fastening points, drill the required holes in the surface of the
column and insert the plugs; now fix the gearmotor in place using suitable
screws and washers.
04. Shorten the slotted arm (fig. 14):
a) To reduce the length of the slotted arm to value C (as established in
point 02-d), unscrew the nut, remove the stop, adjust the two pins so that
the distance between them is equal to value C, then fasten the nut in posi-
tion provisionally.
05. Checking the length C of the slotted arm in this context (fig. 15 - 16):
a) Bring the gate leaf into the fully Closed position;
b) Fully open the gearmotor arm to its maximum extent (see 15, phase 1);
c) Bring the arm up to the gate leaf and hold the fastening bracket against
the leaf: Important! - push the curved arm against the leaf, until it is
secured (maximum opening - see fig. 15, phase 1a).
d) Ensure that the gearmotor arm is levelled properly, and use a pencil to
mark the centre of the slot profile on the bracket, to enable fine adjust-
ments to be made to the closure alignment of the leaf in future (see para-
graph 3.7).
e) Provisionally attach the bracket to the gate leaf and bring the leaf into its
maximum opening position against the ground-mounted stop.
f) With the leaf in this position, perform the checks shown in fig. 16 (run a
wire over the two pins of the slotted arm, as far as the leaf hinge). Impor-
tant! - If, in relation to the hinge, the wire appears in position “BB” as in fig.
16, it will be necessary to extend distance C by a few millimetres. This
must be repeated until the wire reaches position “AA” as in fig. 16 and the
arm is no longer obstructed by the wall or other fixed obstacles.
06. Cutting the slotted arm (fig. 17):
After checking that the articulation is operating correctly, cut the slotted
arm in the following manner.
a) Trace a line on the slotted arm in the position exactly as indicated in fig.
23, phase 1. Then remove the arm from the bracket and cut the part of the
arm which is not required.
b) Re-assemble the components of the arm (fig. 3).
07. Affix the gearmotor arm tot he gate leaf (fig. 18):
a) Drill holes in the gate leaf at the points marked.
b) Remove the bracket from the arm and affix it to the gate leaf with suit-
able screws.
c) Attach the arm to the bracket, inserting the pin and the Benzing retaining
ring. Important - Check that the bracket and the arm are completely level.
Loosen the screws of the bracket and adjust as required to ensure level.
d) Fix the end stops to the ground permanently, in the position determined
at the start of the procedure.
Important! - Check that the gate leaf closes completely against the end
stop. To make fine adjustments to the closure alignment, refer to paragraph
3.7.
e) Finally, bring the leaf manually to around its midpoint of travel and secure
the gearmotor using the dedicated key (see chapter 3.8) Then manually
open the leaf by a few more centimetres.
08. If the gate being automated has two leaves, then to install the other gear-
motor repeat all the actions described here in chapter 3.4.
GRAPH 2B

EN
English – 5
The electrical connection of the various devices (photocells, digital keyboards,
transponder card readers, etc.) of the automation system with a control unit is
carried out with the Nice “Bluebus” system. This system makes it possible to
carry out the electrical connections with the use of just 2 wires along which
both the electricity supply and the communication signals travel. The electrical
connection to be used is parallel and does not require any polarity to be
observed. During the recognition phase, every device connected to the control
unit will be recognised individually by the latter, thanks to a univocal code. Every
time a device is added or removed, you must carry out the control unit recogni-
tion phase (see paragraph 4.7).
ELECTRICAL CONNECTIONS
4
3.5 - Installation of the multi-purpose lamp mod. WLT on the
gearmotor model WL1024C
Warning – WLT can operate as a flashing emergency light or courtesy light,
depending on the control unit programming.
Follow the installation steps shown in fig. 21, making sure the right sequence is
followed and the following warnings are adhered to:
• for stage 4 – Rotate the power unit in the direction of the arrow, keeping a
careful eye on the cables underneath that connect it to the gearmotor.
• for stage 7 – Open out the cables fully and insert the connector into the
FLASH output as shown; secure the cables by inserting them in the cable
gland.
• for stage 11 – Position the electrical board on the pin of the base, depending
on the desired usage: A= diffuse light; B= directional light beam (in this case,
the light beam can be directed by blocking the board in one of the holes on the
base).
• for stage 12 – Open out the cable fully, cut the excess portion and position
the cables in such a way that they do not cast any shadows over the LEDs and
the light sensor fitted on the back of the electrical board.
• for stage 13 – The arrow on the cover and the one on the base should align.
Ensure the 4 cogs on the base fit into the grooves inside the cover.
3.6 - How to remove the control unit
01. Remove the gearmotors lower cover (fig. 19);
02. Undo the 4 screws of the cable sleeve support and remove it (fig. 24,
phase 1-2);
03. Pull the control unit about 4 centimetres in the direction of the arrow, and
detach the motor connector (fig. 24, phase 3-4);
04. Finally, remove the control unit completely;
Important! - When reconnecting the motor to the control unit, observe the
polarity of the connector (this can only be inserted one way around!).
3.7 - Adjusting the alignment of the gate leaves when closed
01. Remove the slotted arm from the fastening bracket on the gate leaf;
02. Loosen the screws on the bracket and move it by a few millimetres towards
the gearmotor;
03. Then replace the slotted arm in the bracket, close the leaf and check that it
is both aligned with the other leaf and in contact with the end stop. Impor-
tant! - If necessary, repeat point 02 until an optimum alignment is achieved;
04. Drill a hole in the leaf, to correspond to the hole in the centre of the fasten-
ing bracket, and insert a screw. Then fix the bracket permanently in place
by tightening the three screws;
05. Finally, attach the slotted arm to the bracket, inserting the pin and the Ben-
zing retaining ring.
3.8 - Securing and releasing the gearmotor manually
The gearmotor is equipped with a mechanical system which allows the gate to
be opened and closed manually.
These manual operations are required in the event of power cuts, operational
faults, or during installation.
Releasing (fig. 22-A):
01. Rotate the release disc clockwise by 90°;
02. Insert the key into the release pin;
03. Turn the key by almost a full turn clockwise.
04. Remove the key from the pin and rotate the release disc anticlockwise by
90° so that the hole is blocked.
05. The gate leaf can now be moved manually into the required position.
Securing (fig. 22-B):
01. Turn the key anticlockwise in the release pin and move the gate leaf manu-
ally until you can hear the leaf engage mechanically with the drive mecha-
nism.
02. Remove the key from the pin and rotate the release disc anticlockwise by
90° so that the hole is blocked.
4.1 - Description of the electrical connections (fig. 23)
M1 gearmotor output 1
ELS output for 12 VAC electrical lock (max 15 VA). [*]
BLUEBUS input for compatible devices (MOFB, MOFOB, MOB and MOTB)
STOP input for devices which, when activated, cause the manoeuvre in
progress to halt immediately, followed by a brief inversion; possibili-
ty of connecting NO, NC contacts or devices with a 8.2 kΩcon-
stant resistance output (sensitive edges). Each device connected to
this input is recognised individually by the control unit during the
recognition phase (paragraph 4.7); after this phase, if the control
unit detects any variation with respect to the status recognised, it
causes a STOP. One or more devices - including different ones -
can be connected to this input:
– several NO devices can be connected in parallel, with no limits as
to quantity;
– several NC devices can be connected in parallel, with no limits as
to quantity;
– 2 devices with a 8.2 kΩ constant resistance output can be con-
nected in parallel. If there are more than 2 devices, they need to be
connected in a cascade configuration with a single termination
resistance of 8.2 kΩ;
– 2 NO and NC devices can be connected in parallel, connecting in
series with the NC contact a 8.2 kΩresistance (this makes the
combination of 3 NO - NC and 8.2 kΩ devices possible)
P. P. input for control devices which, when activated, cause the Step-
step manoeuvre to take place; possibility of connecting NO con-
tacts
AERIAL input for the aerial of a radio receiver
[*] The ELS output can be programmed with other functions using the Oview
programmer (see chapter 8.3).
4.2 - Connecting the power cable
WARNING: The electricity supply line must be equipped with a device which
ensures the complete disconnection of the automation system from the mains.
The disconnection devices contacts must have an opening distance which is
sufficient to achieve full disconnection in category III overload conditions, in
conformance with the rules of installation. When the need arises, this device
ensures that the power is disconnected quickly and safely; it must therefore be
positioned where it can be seen from the automation system. If, however, it is
not located in a visible position, it must be provided with a system to prevent
the power supply being reconnected accidentally or without authorisation, in
order to avoid any risk. The product is not supplied with a disconnection
device.
IMPORTANT!
– The connection must be carried out exclusively by qualified experts.
– All electrical connections must be carried out without any mains electri-
cal power supply and with the back-up battery disconnected - where
present in the automation system.
01. Access the power unit by undoing the 3 screws in the gearmotors upper
cover and slowly rotate the cover in the direction of the arrow (fig. 24),
keeping a careful eye on the cables underneath;
02. Connect the phase and neutral wires to the power unit terminal board,
observing the instructions on the label; close the earth cable grommet
using the screw (fig. 25): care required! -the terminal should be pointing
towards the opening from which the power cable emerges;
03. Then pull the power cable towards the control unit, so that it is just long
enough to allow the power unit to rotate and the cover to close;
04. Close the power unit cover; tighten the screws on the cable gland; insert
the control unit into its seat, and remount the cable sleeve support;
Important! - Fasten the cover of the power unit with all the screws
and ensure that the seal is well positioned in its seat. If the seal or one
of the screws is missing, this can compromise the electronics inside.
4.3 - Connecting the gearmotor without a control unit mod.
WL1024
01. Remove the lower cover of the gearmotor without control unit, as shown in
fig. 19;
02. Using a Phillips screwdriver, undo the 4 screws of the cable sleeve support
and remove it (important! - do not lose the 2 spacers).
03. Loosen the two screws on the cable gland and feed the connection cable
through; connect the 3 cables to the terminal board, observing the sym-
bols as labelled; then tighten the screws of the cable gland.
04. Adjust the 2 feet inside the gearmotor with an Allen key, until they are fully
resting on the column (fig. 20, phase 5).
05. Insert the 6 rubber plugs (provided in the bag containing the small parts) in
the holes in the cable sleeve support; cut the edge of the cable sleeve sup-
port (fig. 20, phase 6); put the 2 spacers back into position; remount the
cable sleeve support and replace the gearmotors lower cover.
4.4 - Connecting other devices
If you need to power further devices in the system, such as a transponder card
reader or the light for the key selector, these devices can be connected to the

EN
6– English
control unit on terminals “P.P. (positive)” and “STOP (negative)” (fig. 26). The
supply voltage varies from 18 to 31 VDC when mains or solemyo operated and
from 11 to approx. 14 VDC when operating on back-up battery PS424. The
maximum available current is 200 mA.
Note – The voltage available in terminals “P.P.” and “STOP” remains present
even when the “Stand By” function is activated on the board.
4.5 - Addressing the connected devices
To allow the control unit to recognise the devices connected to the Bluebus
system, these devices need to be addressed. This must be done by correctly
positioning the electric jumper of each device, referring to the respective
instruction manual of each individual device.
4.6 - Initialisation and connection check
Once you have powered the control unit, carry out the following checks:
•after a few seconds, check that the “Bluebus” LED (fig. 26) flashes regularly
at a frequency of 1 flash per second;
•check that the LEDs of the photocells, both TX and RX, emit flashes. The type
of flashing emitted, at this stage, is not significant;
•check that the WLT multi-purpose lamp is turned off (set on flashing function)
and connected to the FLASH output on the power supply.
If this does not happen, cut off the electricity supply to the control unit and
check the various electrical connections previously carried out.
4.7 - Recognition of the connected devices
Once initialisation is complete, the control unit must recognise the devices con-
nected to the “Bluebus” and “Stop” inputs.
IMPORTANT! – The recognition phase must be carried out even if the
control unit is not connected to any devices.
The control unit is designed to recognise individually the various devices con-
nected to it thanks to the recognition procedure and it can also detect with a
very high degree of precision any possible problems. Consequently, the recog-
nition of devices must be carried out each time a device is connected or
removed.
LEDs “L1” and “L2” on the control unit (fig. 26) emit slow flashes to indicate
that recognition needs to be carried out:
01. Press and keep pressed keys “” and “Set” (fig. 26) simultaneously.
02. Release the keys when LEDs “L1” and “L2” begin to flash quickly (after
approximately 3 seconds).
03. Wait a few seconds for the control unit to complete the device recognition
phase.
04. At the end of this phase, the “Stop” LED should be turned on and LEDs
“L1” and “L2” should turn off (LEDs “L3” and “L4” may start to flash).
4.8 - Recognition of the positions of the mechanical stops
After the recognition of devices (paragraph 4.7), the control unit must recognise
the positions of the mechanical stops (maximum Opening and maximum Clo-
sure);
During this phase, the angle of aperture of the leaf is detected from the closing
mechanical stop to the opening mechanical stop. It is vital that the mechanical
stops are fixed and sufficiently sturdy.
01. Identify the figure corresponding to your system in Table 2, fix the electric
jumpers JA and JB in place on the control unit, in the position as indicated
in this figure.
02. Release the gearmotors with the dedicated keys (see chapter 3.8) and
bring the leaves to their midpoint of travel so that they are free to open and
close; then secure the gearmotors.
03. On the control unit, press and keep keys “Set” and “” pressed simulta-
neously;
04. When LEDs “L3” and “L4” begin to flash quickly, (after approximately 3
secs.) release the keys;
05. Check that the automated system performs the following sequences of
manoeuvres:
a - Slow closure of gearmotor M1 to the mechanical stop
b - Slow closure of gearmotor M2 to the mechanical stop
c - Slow opening of gearmotor M2 and gearmotor M1 to the mechanical
stop
d - Complete quick closure of gearmotors M1 and M2
• If the first manoeuvre of one or both leaves is not a closing movement,
press any key to halt the recognition phase and check the positioning of
electric jumpers JA and JB referring to Table 2; otherwise, check the polar-
ity of the motor without control unit (mod. WL1024).
• If the first motor to start the closing movement is not M1, press any key
to halt the recognition phase and check the positioning of electric jumpers
JA and JB, referring to Table 2.
• If a device is activated during the recognition phase (photocells, key
selector, pressing of a key, etc.), the recognition phase is immediately halt-
ed. It must be repeated in full.
06. At the end of the closing manoeuvre of both motors (d), LEDs “L3” and
“L4” switch off to indicate that the procedure was completed successfully.
4.9 - Gate leaves motion check
At the end of the recognition of the positioning of the mechanical stops, we rec-
ommend you make the control unit perform a few opening and closing
manoeuvres, in order to ensure the gate moves correctly, to check for any
assembly and adjustment defects or other problems:
01. Press the Open key (fig. 26) and check that the Opening manoeuvre
includes an acceleration phase, a phase at constant velocity, a decelera-
tion phase and that the leaves stop against the opening mechanical end
stop.
02. Press the Close key (fig. 26) and check that the closing manoeuvre
includes an acceleration phase, a phase at constant velocity, a decelera-
tion phase and that the leaves stop against the closing mechanical end
stop.
03. Check, during manoeuvres, that the flashing performs certain flashes at 0.5
second intervals with the flashing on and 0.5 seconds with the flashing off.
These are the most important phases in the installation of the automation sys-
tem, in order to guarantee maximum system safety. Testing can also be used to
check the devices in the automation system regularly. The automation system
testing and commissioning phases must be carried out by qualified experts
who must be responsible for determining the tests necessary to check the
solutions adopted vis-à-vis the risks involved, and to check the observance of
all legal and regulatory obligations: in particular all the requirements of the EN
12445 standard which sets forth the test methods for checking automated
gates.
Additional devices must undergo specific testing, both in terms of functionality
as well as their correct interaction with WALKY.; please refer to the relevant indi-
vidual instruction manuals.
TESTING AND COMMISSIONING
5
Overlapping leaf
Overlapping leaf
Overlapping leaf
Overlapping leaf
Control unit
Control unit
Control unit
Control unit
Control unit
Control unit
Control unit
Control unit
TABLE 2

EN
English – 7
5.1 - Testing
The sequence of steps to take to carry out testing refers to a typical system (fig. 2):
1Release the gearmotors manually and check that when you operate the
leaf, at the point designed especially for the manual manoeuvre, the leaves
can either be opened or closed with a force of less than 390 N.
2Check that the leaf, when left in any position along its travel, does not
move.
3Secure the gearmotors (see chapter 3.8).
4Check that the screw connections are screwed in tightly.
5Using the control devices (transmitter, command button, key selector, etc.),
perform some Gate Opening, Closing and Stop tests, making sure the
movement of the leaves corresponds with each test. It is a good idea to
carry out several tests in order to evaluate the movement of the leaves and
pinpoint any assembly or adjustment defects as well as to check for any
particular points of friction.
6Check one by one that all the safety devices in the system work properly
(photocells, sensitive edges, etc.). When a device is activated, the “BLUE-
BUS” LED on the control unit emits two quicker flashes to confirm that
recognition has taken place.
7If the hazardous situations caused by the movement of the leaves have
been safeguarded by limiting the force of impact, the force must be meas-
ured in accordance with the EN 12445 standard and, if necessary, if the
control of the “gearmotor force” is used as an aid to the system to reduce
the force of impact, try and then find the adjustment that achieves the best
results.
8Affix permanently a label describing how to release the gearmotor manual-
ly in an area adjacent to the automation system.
5.2 - Commissioning
Commissioning can only take place once all the testing phases have been
carried out successfully.
1Put together the automation systems technical file, which should include
the following documents: an overall diagram of the automation system, the
diagram of the electrical connections made, the current risk analysis and
the related solutions adopted, the manufacturers declaration of conformity
for all the devices used and the declaration of conformity filled in by the
installer.
2Affix a data plate onto the gate which specifies the following information, at
least: the type of automation system, the name and address of the manu-
facturer (responsible for the commissioning), the serial number, the year of
manufacture and the EC mark.
3Fill in the declaration of conformity of the automation system and hand it
over to its owner.
4Fill in and hand over to the owner of the automation system the “Users
guide” of the automation system.
5Fill in and hand over to the owner of the automation system the “Mainte-
nance schedule” which contains instructions on the maintenance of all the
devices in the automation system.
6Before commissioning the automation system, inform the owner of all the
hazards and residual risks entailed.
For all the documentation mentioned, the Nice technical support service
provides the following: instruction manuals, guides and precompiled forms.
Also visit: www.nice-service.com
TABLE 5 - Level one functions
LED Function Description
L1 Automatic close
L2 Close after photo
L3 Always close
L4 Stand by (Bluebus)
Function ACTIVATED: after an opening manoeuvre, there is a pause (equal to the programmed pause Time) after which the control unit auto-
matically performs a closing manoeuvre. The factory set pause time is 30 sec.
Function DEACTIVATED: operation is “semi-automatic”.
Function ACTIVATED: if the photocells are activated during an opening or closing manoeuvre, the pause time is reduced to 5 sec. irrespective of
the programmed “pause time”.
With the “automatic close” function deactivated, if the photocells are activated during the closing manoeuvre, the “automatic close” is activated
with the programmed “pause time”.
Function ACTIVATED: in the event of a power cut, albeit brief, when the electricity supply returns the control unit detects the open gate and auto-
matically starts a closing manoeuvre, after 5 sec. of pre-flashing.
Function DEACTIVATED: when the electricity supply returns, the gate will remain as is.
Function ACTIVATED: 1 minute after the manoeuvre is finished, the control unit turns off the “Bluebus” output (connected devices) and all LEDs
except for the Bluebus LED which will flash more slowly. When the control unit receives a command, it restores normal operation (with a short
delay). This function is designed to reduce consumption levels, which is a key feature when battery or photovoltaic panel powered.
There are three keys on the control unit. These are OPEN (), STOP (SET) and
CLOSE () and they can be used to operate the control unit during the testing
phases as well as for programming the functions available.
The programmable functions available are arranged on 2 levels and their oper-
ating status is indicated by the 4 LEDs (L1 ... L4) on the control unit (LED on =
function activated; LED off = function deactivated).
Use the programming keys (fig. 26):
OPEN (): – key to control the gate opening; – selection key during the pro-
gramming phase.
STOP/SET: key to stop a manoeuvre; when pressed for more than 5 seconds,
it allows you to enter the programming phase.
CLOSE (): – key to control the gate closing; – selection key during the pro-
gramming phase.
6.1 - Level one programming (ON-OFF)
All level one functions are programmed at the factory to “OFF” and can be
changed at any time. To check the various functions please see Table 5. For
the programming procedure, please see Table 6.
Note – These procedures can be performed again at any time, even after a new
device has been connected to the control unit.
IMPORTANT – The programming procedure has a maximum time of 10 sec-
onds between one key and another being pressed. After this time, the proce-
dure ends automatically, storing the changes made up until that moment.
PROGRAMMING THE CONTROL UNIT
6
TABLE 6 - Level one programming procedure
01. Press and keep key “Set” pressed for approximately 3 seconds;
02. Release the key when LED “L1” begins to flash;
03. Press key “” or “” to move the flashing LED to the LED representing the function you wish to change;
04. Press the “Set” key to change the status of that function:
(brief flashing = OFF - long flashing = ON);
05. Wait 10 seconds (maximum) to exit programming mode.
Note – To program other functions to “ON” or “OFF” when the procedure is in progress, repeat steps 03 and 04 during the phase itself.
L1
or
3 s
10 s

EN
8– English
TABLE 7 - Level two programming procedure
01. Press and keep key “Set” pressed for approximately 3 seconds;
02. Release the key when LED “L1” begins to flash;
03. Press key “” or “” to move the flashing LED to the LED representing the “input LED” of the parameter you wish to change;
04. Press and keep pressed the “Set” key until step 06 is complete;
05. Wait approximately 3 seconds until the LED representing the current level of the parameter to be changed is turned on;
06. Press key “” or “” to move the LED representing the value of the parameter;
07. Release the “Set” key;
08. Wait 10 seconds (maximum) to exit programming mode.
Note – To program several parameters when the procedure is in progress, repeat steps 03 to 07 during the phase itself.
L1
or
or
3 s
10 s
6.3 - Memory deletion
To delete the memory of the control unit and restore all the factory settings, pro-
ceed as follows: press and keep pressed keys “” and “” until LEDs L1 and
L2 start to flash.
6.4 - Special functions
Function: “Move anyway”
This function makes it possible to operate the automation system even when a
safety device is not working properly or is out of order.
The automation system can be controlled in “push to run” mode as follows:
01. Send a command to operate the gate, using a transmitter or key selector,
etc. If everything is working properly, the gate will move normally, otherwise
proceed as follows:
02. within 3 seconds, send the command again and keep it activated;
03. after approximately 2 seconds, the gate will perform the manoeuvre
requested in “push to run” mode; i.e. the gate will continue to move only
for as long as the command is activated.
When the safety devices do not work, the flashing light emits a few flashes to
indicate the type of problem (see chapter 7 - Table 10).
TABLE 8 - Level two functions
LED Parameter LED Value Description
input (level)
L1 L1
L2
L3
L4
5 seconds
30 seconds
60 seconds
120 seconds
Adjusts the pause time, i.e. the amo-
unt of time before the gate closes au-
tomatically. Only effective is Close is
activated.
Pause
Time
L2 L1
L2
L3
L4
Opens – stop – closes – stop
Opens – stop – closes – opens
Opens – closes – opens – closes
Apartment building:
• during the opening manoeuvre, the “Step-Step” and “Opens” commands
do not have any effect; on the other hand, the “Closes” command causes
the movement to be inverted, i.e. the leaves to close.
• during the closing manoeuvre, the “Step-Step” and “Opens” commands
cause the movement to be inverted, i.e. the leaves to open; on the other
hand, the “Closes” command does not have any effect.
Adjusts the sequence of commands
associated with the “Step-Step” in-
put or radio command.
Note – When L4 is set, the behaviour
of the “Opens” and “Closes” comma-
nds is also modified.
Step-Step
Function
L3 L1
L2
L3
L4
Slow
Medium
Fast
Very fast
Adjusts the velocity of the motors du-
ring normal travel.
Motor
velocity
L4 L1
L2
L3
L4
Level 1 - Minimum force
Level 2 - ...
Level 3 - ...
Level 4 - Maximum force
Adjusts the force of both motors.
Motor
force
6.2 - Level two programming (adjustable parameters)
All level two parameters are programmed at the factory as highlighted in grey in
Table 8 and can be modified at any time following the procedure described in
Table 7.
The parameters are adjustable on a scale of values from 1 to 4; to check the
value corresponding to each LED, please see Table 8. IMPORTANT –The pro-
gramming procedure has a maximum time of 10 seconds between one key and
another being pressed. After this time, the procedure ends automatically, stor-
ing the changes made up until that moment.

EN
English – 9
Some devices are designed to emit signals which help you recognise their
operating status or any problems.
If the WLT multi-purpose lamp is connected to the FLASH output on the power
supply and set with the flashing function, during the performance of a manoeu-
vre, it emits a flashing light every second. If any problems are encountered, the
flashing emits shorter flashes, which are repeated twice, divided by a 1 second
pause. Table 10 describes the cause and solution for each type of signal.
The LEDs on the control unit also emit signals; Table 11 describes the cause
and solution for each type of signal.
WHAT TO DO IF... (troubleshooting guide)
7
7 brief flashes
1 second pause
7 brief flashes
Electrical circuits fault Wait at least 30 seconds and then try to repeat the command and if necessary cut off
the power supply; if the status remains the same, there might be a serious failure and the
electrical board may need replacing.
8 brief flashes
1 second pause
8 brief flashes
A command has already been given,
which does not allow any other com-
mands to be performed
Check the nature of the command in progress; it could for example be the command
from a clock on the “opens” input.
9 brief flashes
1 second pause
9 brief flashes
The automation system was secured
by a “Secure the automation system”
command
Release the automation system by sending the “Release the automation system” com-
mand.
TABLE 10 - Flashing light signals (FLASH)
Flashes Problem Solution
1 brief flashing
1 second pause
1 brief flashing
Error on the Bluebus system The check of the devices connected to the Bluebus system, which is carried out at the
beginning of the manoeuvre, does not correspond to the devices stored during the
recognition phase. There might be devices which are disconnected or out of order, so
you need to check and replace them if necessary. If modifications have been made, you
will need to repeat the recognition of devices (see paragraph 4.7).
2 brief flashes
1 second pause
2 brief flashes
Photocell activation One or more photocells are not are not permitting movement or during travel they
caused the movement to be inverted; check for any obstacles.
3 brief flashes 1-se-
cond pause 3 brief fla-
shes
Activation of the “Obstacle Detection"
by the force limiting device During the movement, the motors encountered greater effort; verify the cause and
increase the force of the motors if necessary
4 brief flashes
1 second pause
4 brief flashes
STOP input activation At the beginning of the manoeuvre or during the movement, one of the devices connect-
ed to the STOP input was activated; verify the cause.
5 brief flashes
1 second pause
5 brief flashes
Error in the internal parameters of the
control unit Wait at least 30 seconds and then try to repeat the command and if necessary cut off the power supply; if the status remains the same, there might be a serious failure and the
electrical board may need replacing.
6 brief flashes
1 second pause
6 brief flashes
Maximum limit of consecutive manoe-
uvres or manoeuvres per hour excee-
ded.
Wait a few minutes in order to allow the manoeuvres limiting device to return to below
the maximum limit.
TABLE 11 - Signals from the LEDs on the control unit (fig. 23)
LED Problem Solution
BLUEBUS
lways off
Always on
1 flash per second
2 fast flashes
Series of flashes divided by a
one-second pause
Fault
Serious fault
All ok
Change in the status of the inputs
Other
Ensure the control unit is powered; check whether the fuses have blown.
In this case, check the cause of the fault and replace them with others of
the same value
There is a serious fault: try to cut off the electricity supply to the control unit
and if the status remains, then you will need to replace the electrical board
Normal operation of the control unit
If it normal if a variation in one of the input takes place (PP, STOP): pho-
tocells activation or a command is transmitted with a transmitter
Please refer to Table 10
STOP
Always off
Always on
Activation of the devices connected to the
STOP input
All ok
Check the devices of the STOP input
STOP input activated
P.P.
Always off
Always on
All ok
Activation of the P.P. input
P.P. input deactivated
It is normal if the device connected to the P.P. input is activated
L1 - L2 Slow flashing Change in the number of devices
connected to the Bluebus or device recogni-
tion not performed
The recognition of devices must be carried out (see paragraph 4.7)
L3 - L4 Slow flashing The recognition of the positions of the
mechanical stops was not carried out The recognition must be carried out (see paragraph 4.8).

EN
10 – English
The following accessories are envisaged for WALKY (radio receiver): the Oview
programmer, the Solemyo solar power system and the back-up battery mod.
PS424.
8.1 - Connection of the OXI radio receiver
To connect the OXI receiver, first cut off the electricity supply to the control unit
and proceed as illustrated in fig. 27.Table 12 and Table 13 indicate the com-
mands which correspond to the outputs on the control unit.
8.2 - Connection and installation of the back-up battery
mod. PS424
IMPORTANT! - The battery must only be connected to the control unit
after all the phases of installation and programming have been complet-
ed, as the battery constitutes a source of emergency power.
To arrange connection to the Solemyo system, follow the stages of assembly
fig. 28.
8.3 - Connection of the Oview programmer
The control unit has a BusT4 connector to which the Oview programming unit
can be connect, and which allows the complete rapid management of the
installation and maintenance phase as well as the diagnosis of the entire
automation system. To access this connector, proceed as shown in fig. 29 and
connect the connector to the dedicated seat. The Oview can be connected to
several Control units simultaneously (up to 5 without any particular precautions,
and up to 60 observing the dedicated warnings) and can stay connected to the
control unit even during the normal operation of the automation system. In this
case, it can be used to send the commands directly tot he control unit using the
specific "user" menu. The Firmware upgrade can also be carried out. If there is
a radio receiver from the OXI family in the control unit, Oview can be used to
gain access to the parameters of the transmitters stored in the receiver itself.
For further information, please consult the relevant instruction manual and the
manual for the “Opera system book” system.
8.4 - Connection of the Solemyo solar power system
IMPORTANT! – When the automation system is powered by the “Sole-
myo” system, IT MUST NOT BE POWERED concurrently by the electricity
mains.
For further information about the Solemyo system, please refer to its instruction
manual.
To arrange connection to the Solemyo system, follow the stages of assembly
illustrated in fig. 30.
To complete the connection between Solemyo and the gearmotor control unit,
use the dedicated adapter cable.
FURTHER INFORMATION
8
1 Step-Step
2 Partial opening 1
3 Opens
4 Closes
5 Stop
6 Step-Step
Apartment Building
7 Step-Step
high priority
8 Partial opening 2
9 Partial opening 3
10 Opens and Secure
automation system
11 Closes and Secure
automation system
12 Secure automation
system
13 Release automation
system
14 On Timer Courtesy
Light
15 On-Off Courtesy
Light
TABLE 13
OXI / OXIFM /OXIT / OXITFM in mode II extended
No. Command Description
Command “P.P.” (Step-Step)
Command “partial opening 1”
Command “Opens”
Command “Closes”
Stop the manoeuvre
Command in Apartment Building mode
Command even with automation system secured or com-
mands activated
Partial opening (opening of leaf M2 to half of its total travel)
Partial opening (opening of both leaves to half of their total
travel)
Causes an opening manoeuvre at the end of which the
automation system is secured; the control unit does not
accept any other command except for the “Step-Step
high priority”, “Release” automation system or (only from
Oview) the commands: “Release and close” and “Release
and open”
Causes a closing manoeuvre at the end of which the
automation system is secured; the control unit does not
accept any other command except for the “Step-Step
high priority”, “Release” automation system or (only from
Oview) the commands: “Release and close” and “Release
and open”
Causes the manoeuvre to be stopped and the automation
system to be secured; the control unit does not accept
any other command except for the “Step-Step high priori-
ty”, “Release2 automation system or (only from Oview) the
commands: “Release and close” and “Release and open”.
Causes the automation system to be released and normal
operation to be restored
The Courtesy light output is turned on with timed switch-
off
The Courtesy light output is turned on and off in On-Off
mode
PRODUCT MAINTENANCE
9
In order to keep the safety level constant and to guarantee the maximum life
span of the entire automation system, regular maintenance is vital.
All maintenance work must be carried out in compliance with the safety provi-
sions of this manual and in accordance with existing laws and regulations.
The product requires frequent inspection to check for imbalances or signs of
wear or damage to the cables and springs. Do not use the product if adjust-
ments or repairs are required.
Important – During the product maintenance or cleaning operations, cut
off the electricity supply to the control unit.
For the other devices in the system, follow the instructions provided in their
respective maintenance schedules.
For gearmotors WL1024C, WL1024 and WL2024, scheduled maintenance is
required at the latest 6 months or 20,000 manoeuvres after the previous main-
tenance work.
Maintenance can be performed as follows:
01. Cut off any electrical power source, including any back-up batteries;
02. Check the condition and wear of all the materials making up the gearmotor,
paying special attention to erosion or rusting; replace all parts which do not
provide sufficient guarantees;
03. Reconnect the electrical power sources and perform all the checks envis-
aged in chapter 5.1 - Testing.
TABLE 12
SMXI / SMXIS or OXI / OXIFM / OXIT / OXITFM in mode I or Mode II
Output 1
Output 2
Output 3
Output 4
Command “P.P.” (Step-Step)
Command “partial opening 1”
Command “Opens”
Command “Closes”

EN
English – 11
DISPOSING OF THE PRODUCT
This product is an integral part of the automation system, and should
therefore be disposed of together with it.
As for the installation operations, even at the end of this products life span, the
dismantling operations must be carried out by qualified experts.
This product is made up of various types of materials: some can be recycled
while others need to be disposed of. Find out about the recycling or disposal
systems envisaged by your local regulations for this product category.
Important! – parts of the product could contain pollutants or hazardous sub-
stances which, if released into the environment, could cause harmful effects to
the environment itself as well as to human health.
As indicated by the symbol opposite, throwing away this
product as domestic waste is strictly forbidden. So dispose
of it as differentiated waste, in accordance with your local
regulations, or return the product to the retailer when you
purchase a new equivalent product.
Important! – the local applicable regulations may envisage heavy sanctions in
the event of illegal disposal of this product.
Disposal of the back-up battery (where present)
Important! – The flat battery contains pollutants and should therefore not be
thrown away as common waste.
It should be disposed of as differentiated waste, as envisaged by your local
applicable regulations.
PRODUCT TECHNICAL SPECIFICATIONS
WARNINGS: • All technical specifications are referred to a room temperature of 20°C (± 5°C). • Nice S.p.a. reserves the right to make any changes deemed nec-
essary to the product at any time while maintaining the same functions and intended use.
Type: Electric gearmotor for automated gates and doors with direct reduction gear and mechanical release mechanism. Only for model WL1024C: built-in con-
trol unit and OXI radio receiver
Maximum torque: 100 Nm
Nominal torque: 50 Nm
Idle velocity: 0.20 rad/s - 0.3 rad/s
Velocity of nominal torque: 0.16 rad/s - 0.24
Maximum cycle frequency: 100 complete cycles per day (the control unit of WL1024C limits to a maximum of approximately 50
Maximum continuous cycle time: approx. 10 minutes
Usage limitation: the product can be used on gates weighing up to 180 kg (0.8 m leaf) pr with a leaf length of up to 1.6 m and an angle of aperture of up to
110°
Power supply: WL1024C: 230 VAC (+10% -15%) 50/60 Hz; WL1024: 24 VDC (50%); WL1024C/V1: 120 VAC (+10% -15%) 50/60 Hz
Emergency power supply: Designed to accommodate back-up battery PS424
Solar panel power supply: designed to accommodate SOLEMYO kit
Nominal absorbed power from electricity mains (WL1024C): 120 W
Nominal absorbed current (WL1024): 2 A; at pick-up the current is 3 A for a maximum time of 2 s
Power absorbed from the electricity mains with “Standby – All (1)” function activated (including the OXI receiver): 3 W
Power absorbed when operating on back-up battery or SOLEMYO KIT with “Standby-All (1)” function activated: less than 100 mW (including the OXI
receiver)
Electrical lock output [*]: a 12 VAC max 15 VA electrical lock
Flashing output [*]: a flashing WLT or a 12VDC lamp, 21 W max
BLUEBUS output: an output with maximum load of 15 Bluebus units (maximum 6 pairs of MOFB or MOFOB photocells + 2 pairs of MOFB or MOFOB photo-
cells addressed as opening devices + maximum 4 MOMB or MOTB control devices)
STOP input: for normally closed, normally open contacts or with a constant resistance of 8.2 kohm; the selection of the type of contact takes place in auto-
recognition and a variation compared to the status stored causes the “STOP” command
PP input: for normally open contacts (the closing of the contact causes the Step-Step command)
Radio connector: SM connector for receivers from the SMXI, OXI and OXIFM families
Radio AERIAL input: 50 ø for type RG58 or similar cable
Programmable functions: 4 ON-OFF type functions (Table 5) and 4 adjustable functions (Table 8)
Functions in auto-recognition: • Auto-recognition of the devices connected to the BlueBus output. • Auto-recognition of the type of device connected to the
“STOP” terminal (NO, NC or 8.2 kohm resistance contact). • Auto-recognition of the travel of the leaves and automatic calculation of the points of deceleration
and partial opening. • Auto-recognition of operation with one or two motors
Assembly: Vertically, with dedicated fastening plate
Operating temperature: from -20°C to +50°C (at low temperatures the efficiency of the gearmotor decreases)
Usage in particularly acidic or saline or potentially explosive atmosphere: NO
Protection rating: IP 44 (with casing intact)
Dimensions (mm): 90 x 125 x 385 h
Weight (kg): (WL1024C) 4.8; (WL1024) 4.3
Note:
––––––––––
(1) - Function which can be activated with the Oview programmer.
[*] - The outputs of the terminals on the control unit (“Electrical lock”) and on the power unit (“Flash”) can be reprogrammed with other functions, using the Oview programmer. The elec-
trical characteristics of these two outputs are adapted depending ont he type of function chosen:
• “electrical lock” function: 12VAC, 15VA max;
• “flashing” function: a WLT multi-purpose lamp, or a 12VDC lamp, 21W max;
• other types of functions: a lamp or a relay at 24VDC (-30 and +30%), 4 W max, if the control unit is mains powered, or a lamp or relay at 12VDC (-10 and +25%), 4 W max, if the con-
trol unit is powered by the back-up battery PS424.

EN
12 – English
EC DECLARATION OF CONFORMITY
Note - The contents of this declaration correspond to the declarations contained in the latest available revision, prior to printing of this manual, of the official document on file at
the headquarters of Nice S.p.a. This text was readapted for editorial purposes.
Number: 322/WL.. Revision: 0
The undersigned Luigi Paro, as Managing Director, declares on his own responsibility that the product:
Name of manufacturer: NICE s.p.a.
Address: Via Pezza Alta 13, Z.I. Rustignè, 31046 - Oderzo (TV) Italy
Type: Electric gearmotor
Models: WL1024C, WL1024
Accessories: OXI, OVBT, OVBTGSM, SYKCE, PS24
are compliant with the provisions of the following EC directives:
• 98/37/CE (89/392/EEC amended) DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 22 June 1998 concerning stan-
dardization of the legislation of member states on machinery
As envisaged in directive 98/37/EC, please note that the commissioning of the above product is not permitted until the machine in which the product is
installed has been identified and declared as conforming to directive 98/37/EC.
The product is also compliant with the provisions of the following EC directives, as amended by Directive 93/68/EEC of the council of 22 July 1993:
• 2006/95/EEC (ex-directive 73/23/EC) DIRECTIVE 2006/95/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 12 December 2006 con-
cerning standardization of member states on electrical material to be used within certain voltage limits
In accordance with the following harmonized standards:
EN 60335-1:1994+A11:1995+A1:1996+A12:1996+A13:1998+A14:1998+A15:2000+A2:2000+A16:2001
• 2004/108/EEC (ex-directive 89/336/EEC) DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 15 December 2004
concerning standardization of the legislation of member states on electromagnetic compatibility and which repeals 89/336/EEC
In accordance with the following harmonized standards: EN 61000-6-2:2005; EN 61000-6-3:2007
It is also compliant - limited to the applicable parts - with the following standards:
EN 60335-1:2002+A1:2004+A11:2004+A12:2006+ A2:2006, EN 60335-2-103:2003,
EN 13241-1:2003; EN 12453:2002; EN 12445:2002; EN 12978:2003
Oderzo, 29 May 2009 Luigi Paro (Managing Director)
Example of life span calculation for a X-Metro gearmotor (please refer to
Table 1 and Graph A):
- weight of leaf: 50 kg (strenuousness index: 20%)
- length of leaf = 1.6 m (strenuousness index: 20%)
- no other straining elements present
Total strenuousness index = 40%
Estimated life span = 65.000 manoeuvre cycles
Product life span
The product life span is its average commercial life. The value of the product life
span is strongly affected by the strenuousness index of the manoeuvres per-
formed by the automation system: i.e. the sum of all the factors which con-
tribute to the product wear (see Table 14).
To determine the probable life span of your automation system, proceed as fol-
lows:
01. Calculate the strenuousness index by adding together the percentage val-
ues of the items in Table 14;
02. In Graph A trace a vertical line from the value as just calculated until it inter-
sects the curve; from this point, trace a horizontal line until it intersects the line
of the “manoeuvre cycles”. The value determined is the estimated life span of
your product.
The life span estimate is based on design calculations and on the results of
tests performed on prototypes. Indeed, since it is an estimate, it is in no way a
guarantee as to the actual duration of the product.
Walky Walky
full length arm shortened arm
Strenuousness index
< 100 Kg - -
Weight of leaf: 100 - 120 Kg 30 % 30 %
120 - 140 Kg 40 % 40 %
140 - 160 Kg 45 % 45 %
1,2 - 1,6 m 20 % 0 %
Length 0,8 - 1,2 m 10 % 10 %
of the leaf: < 0,8 m - 5 %
Room temperature
above 40°C or below 20 % 20 %
0°C or humidity above 80%
Blind leaf: 15 % 15 %
Installation in windy area: 15 % 15 %
TABLE 14
GRAPH A
manoeuvre cycles
strenuousness index %

I
EN Appendix
• Instructions and warnings for the user
• Images
IT Appendice
• Istruzioni ed avvertenze destinate allutilizzatore
• Immagini
FR Appendice
• Instructions et recommandations destinées à lutilisateur
• Images
ES Apéndice
• Instrucciones y advertencias destinadas al usuario
• Imágenes
DE Anhang
• Anweisungen und Hinweise für den Benutzer
• Bilder
PL Załącznik
• Instrukcje i zalecenia przeznaczone dla użytkownika
• Zdjęcia
NL Bijlage
• Aanwijzingen en aanbevelingen voor de gebruiker
• Afbeeldingen

EN
English – III
• If the automation system was secured with the command "Secure
automation system”: after a command is sent, the gate does not move and
the flashing light emits 9 brief flashes.
SECURING AND RELEASING THE GEARMOTOR MANUALLY
The gearmotor is equipped with a mechanical system which allows the gate to
be opened and closed manually.
These manual operations are required in the event of power cuts and opera-
tional faults.
Note - When there is no electrical power, the gate can still be moved using
power from the back-up battery (mod. PS424), if included in your system.
Releasing (fig. A):
01. Rotate the release disc clockwise by 90°;
02. Insert the key into the release pin;
03. Turn the key by almost a full turn clockwise.
04. Remove the key from the pin and rotate the release disc anticlockwise by
90° so that the hole is blocked.
05. The gate leaf can now be moved manually into the required position.
Securing (fig. B):
Note – As an effect of the elasticity of the leaf, after it is released with the leaf
closed, it may not be possible to secure the leaf in the same position.
01. Turn the key anticlockwise in the release pin and move the gate leaf manu-
ally until you can hear the leaf engage mechanically with the drive mecha-
nism.
02. Remove the key from the pin and rotate the release disc anticlockwise by
90° so that the hole is blocked.
Instructions and warnings for the user
Before using the automation system for the first time, allow the installer to
explain the origin of the residual risks and take a few minutes to read this
instruction manual and the warnings for the user which the installer has handed
you. Keep this manual in a safe place for future reference and hand it over to
any new owner of the automation system.
IMPORTANT! – Your automation system is a machine which per-
forms the commands you send it; improper and careless use could
make it become dangerous:
– Do not operate the movement of the automation system if people, ani-
mals or objects lie in its range of action.
– It is strictly forbidden to touch parts of the automation system while the
gate or door are in motion!
– The photocells are not a safety device but one that is auxiliary to safety.
They are built with high reliability technology but they may, under
extreme circumstances, malfunction or indeed fail and, in some cases,
the failure may not immediately be visible. For these reasons, please
observe the following warnings when using the automation system:
- Transit is only permitted if the gate or door is completely open and with
the leaves at a standstill
- IT IS STRICTLY FORBIDDEN to transit while the gate or door is closing!
- Ensure the photocells are working properly on a regular basis.
• Children: an automation system guarantees a high level of safety; indeed,
thanks to its detection systems, it controls and guarantees movement in the
presence of people or objects. It is however prudent to forbid children from
touching or playing near the automation system and not to leave remote con-
trols within their reach to avoid involuntary activation: it is not a game!
• The product is not intended for use by persons, including children, with limit-
ed physical, sensory or mental capacities, or who lack experience or knowl-
edge, unless supervised or trained in the use of the product by a person
responsible for their safety.
• Faults: if an operating fault is detected in the automation system, cut off the
electricity supply to the automation system and release the gearmotor manual-
ly (see respective instruction manual) to operate the gate manually. Do not per-
form any repair work but contact your regular installer for assistance.
•Do not change the system or the programming and adjustment parame-
ters of the control unit: this lies within the area of responsibility of your
installer.
• Breakage or lack of power supply: while waiting for your installer to call
by or for the power supply to be re-established, if the system is not equipped
with a back-up battery, the automation system can still be used: simply perform
the manual release of the gearmotor (see the respective instruction manual) and
move the gate leaf manually as required.
• Safety devices out of order: the automation system can still work when a
safety device doesnt work properly or is out of order. The gate can be con-
trolled in “push to run” mode as follows:
01. Send a command to operate the gate, using a transmitter or key selector,
etc. If everything is working properly, the gate will move normally, other-
wise proceed as follows:
02. Within 3 seconds, send the command again and keep it activated;
03. After approximately 2 seconds, the gate will perform the manoeuvre
requested in “push to run” mode; i.e. the gate will continue to move only
for as long as the command is activated.
N.B.! – If the safety devices are out of order, we recommend you have
them repaired as soon as possible by qualified experts.
• The testing, routine maintenance and any repair work must be documented
by the person who carries out the work; the documents must be kept by the
owner of the system. The only operations that the user can perform regularly
are the cleaning of the glass covers of the photocells (use a slightly damp soft
cloth) and the removal of any leaves or pebbles which could hamper the
automation system. Important – Before going ahead, to prevent someone from
being able to activate the gate inadvertently, release the gearmotor manually
(see the respective instruction manual).
• Maintenance: in order to keep the safety level constant and to guarantee
the maximum life span of the entire automation system, regular maintenance (at
least every 6 months) is vital. All control, maintenance or repair operations
must only be carried out by qualified experts.
• Disposal: at the end of the life span of the automation system, make sure
that it is dismantled by qualified experts and that the materials are disposed of
in accordance with the applicable local regulations.
1
32
1
2
3
B
A

X
1
2
2a
385 mm
125 mm85 mm

3
XI
6
7
4
5

XII
1
2
3
4
5 6
78
9
10 12
11
8

XIII
1 23 4
~45°
~45°
2
3
1
ac
b
OK
OK
b
a
9
a
a
b
5 67
8 9 10
11 12 13