Wampat W11F6071W User manual

W11F6071W
W11F6072C
Assembly Instructions
Please read this manual carefully before beginning assembly of this product.Keep this manual for future reference.

1-1

1
1
2
3
4
5
6
7
7
8
9
10
11
12
13
14
15
16
17
18
x 4

2
ABC E
I
GJ
H
F
D
KL
MNOP
Y
x 1 x 18 x 8 x 12
x 2
x 20 x 4
x 2
x 20
x 12
x 8 x 20
x 6 x 4 x 6 x 6
x 1
CH
Handle bolt
M4x21-Ø8mm
Handle Screw
Ø4x30mm
Footpads
Handle
Tipping restraint hardware kit
(inside plastic bag)
Philips screwdriverr
Tools Required
(Not included)
Glue tube Wooden dowel
Ø8x30mm
Wooden dowel
Ø6x30mm
Cam lock
Ø15x12mm Ø7x34mm
Cam bolt Cam lock
Ø14x11mm
Ø6x29mm
Cam bolt Handle bolt
M4x12-Ø8mm
Screw
Ø4x40mm Plastic wedge Screw
Ø3x16mm

3
1
● The provided glue(A) is to secure wood
dowels(B) in place . When first inserting
dowels, locate the appropriate hole for the
dowel , place a small amount of glue in the
hole and insert the dowel . Wipe away
excess glue immediately.
● In future assembly steps when dowels are
necessary to attach assembly parts together,
place a small amount of glue on the end of
the dowel before attaching parts together.
Wipe away excess glue immediately.
Philips head screwdriver
required for assembly
(not included)
· Screw cam bolts (E) into panels (3,4).
· Insert dowels (B) into panels (3,4).
4
3
E
B
B EA
1 2
1 2
x 8 x 8
x 1

4
2
· Insert dowels (B) into panels (6,7).
67
x 2
B
B
BA x 10
x 1

5
3
· Attach panels (6,7) to panels (3,4).
· Insert and secure cam locks (D) to panels (6,7) to lock it.
6
7
7
3
4
D
DA x 8
x 1
1 2 3

6
4
· Attach panel (2) to panels (3,4,6) using screws (M).
4
3
6
2
M
M
Ax 1 x 6

7
5
· Attach legs (8) to panel (2) .
· Stick the skid pads (N) on the bottom of the legs (8).
8
NN
N
2
x 4

8
6
·Carefully slide panel (5) into place along the back of the assembly.
5
5

9
7
· Screw cam bolts (E) into panel (1).
E
E
1
x 4

10
8
· Attach panel (1) to panels (3,4).
· Insert and secure cam locks (D) to panels (3,4) to lock it.
1
3
4
DA
D
x 4x 1
1 2 3

11
9
· Secure parts (O) to panels (1,3,4,6) using screws (P).
O
P
5
1
3
4
6
P
Ox 6x 6

12
10
· Attach panels (11,12) to panel (10) with screws (L).
· Carefully slide panel (13) into place along the bottom of the assembly.
12
11
10
13
12
11
L
Lx 4

13
11
· Screw cam bolts (G) into panel (9).
· Attach Handle (H) to panel (9) with bolts (I).
· Attach panel (9) to panels (11,12).
· Insert and secure cam locks (F) to panels (11,12) to lock it.
9
G
I
H
F
9
12
11
FIH
G
x 4 x 2 x 2x 4
1 2 3

14
12
· Screw cam bolts (G) into panel (14).
· Attach Handle (J) to panel (14) with bolts (K).
· Insert dowels (C) into panels (16,17).
G
K
J
14
C
17
16
GC
A K J
x 4
x 16
x 8
x 1 x 8 x 4

15
13
· Attach panels (16,17) to panel (15) with screws (L).
· Carefully slide panel (18) into place along the bottom of the assembly.
17
16
15
L
18
17
16
L
x 4
x 16

16
14
· Attach panel (14) to panels (16,17).
· Insert and secure cam locks (F) to panels (16,17) to lock it.
F
14
17
16
x 4 Fx 16
1 2 3
Ax 1

17
15
9
14
14
14
14
1
Slider bracket
· Assembled the drawers as per diagram
Note :
If the drawer does not go in smoothly.
Press or lift the plastic release lever.
Pull out the slider bracket from
the slider arm.
Loosen the screws on slider brackets,
You can adjust up or down by a few mm.
Then tighten back up.
Finally re-assembled the drawer until
they were going in smoothly well.
Slider arm
Slider bracket

18
16
Connector
Serious or fatal injuries can occur from furniture tipping over.
To prevent the furniture from tipping over we recommend that
it is permanently fixed to the wall. Wall anchor and hardware
are included with this product. Please make sure hardware is
suitable for your walls before installing, as different wall
materials may require different types of anchors.
Tools required: Phillips screwdriver, Power Drill,
2/5” Drill Bit and Rubber Mallet.
e
e
e
1
e
b
c
a
d
d
1
1 2 3
x 1
Y
Wall
WARNING