Warehouse-lighting LTR Series User manual

1 of 3
INSTALLATION INSTRUCTIONS
LTR™Series
LED Troffer Retrot Kit
Includes: LTR-22, LTR-24
WARNING
FAILURE TO FOLLOW THESE INSTRUCTIONS AND WARNINGS MAY RESULT IN SERIOUS INJURY OR DAMAGE TO
PROPERTY
For your safety, thoroughly read these instructions and warnings in its entirety prior to installing or servicing this product. These
instructions do not attempt to cover all installation and maintenance circumstances. If you do not understand these instructions or
if additional information is needed, please contact Aleo Lighting customer service.
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
WARNING
RISK OF FIRE OR ELECTRIC SHOCK
This product must be installed and serviced by a
professional electrician in accordance with applicable
federal, state, and local laws, regulations, and
electrical code. If not qualied, do not attempt
installation of this product. Contact a qualied
electrician.
WARNING
RISK OF FIRE, ELECTRIC SHOCK, or PERSONAL INJURY
To avoid risk of electrical shock, turn off power before installing or
servicing.
Verify that supply voltage is correct by comparing with the input
voltage on the luminaire label
Make all electrical and ground connections in accordance with
NEC and any applicable code requirements
WARNING
RISK OF PERSONAL INJURY
To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects
Do not make or alter any open holes in any of the enclosures with wiring or electrical components during installation
Suitable for Dry or Damp Location
WARNIN
G
This luminaire is made for permanant installation in ordinary (non-hazardous) locations in accordance with NEC
code and all applicable local and federal codes. Do not use in applications with limited ventilation or high ambient
temperature enclosures.
Contents to change without notice.
Wiring Diagram
Electrical Connection
1. Connect BLACK (line) driver lead to voltage supply Line
position (HOT).
2. Connect driver WHITE lead to the NEUTRAL supply
position.
3. Connect the GREEN ground lead to the supply ground
lead.
If using 0-10V dimming:
4. Connect VIOLET lead to supply POSITIVE dimming lead.
5. Connect GREY lead to the supply NEGATIVE dimming
lead.
If NOT using 0-10V dimming:
6. Ensure VIOLET and GREY 0-10V dimming leads are
properly capped.
LED DRIVER
Black (Line)
White (Neutral)
Line Voltage (120V-277V)
0-10V
Control Wires
Violet (Dim +)
Grey (Dim -)
Blue (-)
Red (+)
LED
Load
TURN OFF POWER BEFORE INSTALLING

2 of 3
TO INSTALL: LTR™Series
LED Troffer Retrot Kit
A: Side Bracket (x2)
B: LED Gear Tray
C: Reector
D: Lens Diffuser
E: Label
F: 1/4-turn Fasteners
G: Safety Lanyard Kit
A
Kit Contents
B
C
D
E
Tools Required
Drill
Pliers
Cutters
Gloves
Screw Driver (optional)
CAUTION: TURN OFF POWER BEFORE INSTALLING
1 2
Remove Lens or cover. Remove lamps and original ballast cover.
3
Disconnect AC mains from ballast.
4
Side Brackets (A)
Install Side Brackets (A) by sliding
in-between host troffer and ceiling
T-bar grid.
5
Slide Side Brackets (A) outwards as
far as possible, until they sit against
the end of each side of the troffer.
6
1
2
LED Gear Tray (B)
Install LED Gear Tray (B) by sliding
in-between host troffer and T-bar.
Ensure tabs from Side Brackets
engage in Gear Tray Slots.
DO NOT TOUCH LED
7
Push Gear Tray upwards and tuck tabs
above the Side Panels so that the Gear
Tray sits above the Side Panels. Fasten
Gear Tray by inserting and turning 1/4-
turn fasteners (supplied) 90°.
Place Label (E) inside existing host troffer
housing.
8
THIS LUMINAIRE HAS BEEN MODIFIED
FROM ITS ORIGINAL CONFIGURATION.
THIS LUMINAIRE WILL NO LONGER
ACCEPT THE ORIGINAL LAMPS
STATED ON THE RELAMP LABEL.
Fasten Safety Lanyard cables (G)
by fastening self-tapping tek screws
to existing host troffer housing. Clip
opposing end of safety cable to Gear
Tray (B).
9

3 of 3
12
12
Install Reector (C) by inserting between
host troffer and T-bar. Swing Reector
upwards.
Secure Reector by inserting 1/4-turn
fastener (supplied) and rotating 90°.
Remove protective packaging from LED
modules. Place Lens Diffuser (D) onto
retrot kit by squeezing sides of Lens
Diffuser and inserting edges into grooves
of Gear Tray and Reector. Lens may
need to be adjusted by squeezing sides
or pressing the face of the lens.
Ground Connection
OPTION A:
Securely fasten ground screw lead from
Gear Tray (B) to host troffer if host troffer
is grounded.
BA Conduit (Supply)
Retrot Kit
Ground
Connection
LED Driver
Electrical Connection (AC Mains)
Follow instructions and wiring diagram on Page 1 to
connect AC mains to Gear Tray input leads. Retrot
kit comes equipped with quick disconnect. Hide
wires behind Gear Tray. Ensure leads do not hang
out of Gear Tray to avoid electrical wiring being
clamped between metal parts.
LED Driver
AC Mains
Retrot Kit
Host Troffer
OPTION B:
Connect ground from Gear Tray (B) to
supply ground lead from conduit.
11
13 14
10
LTR™Series