Warrior Table Soccer Warrior Pro User manual

Updated: 5/4/16 www.WarriorTableSoccer.com
SOCCER TABLE
Assembly Instructions

Table of Contents
Parts Identifier .......................................... 3
Hardware Identifier…………………………. 4
Table Assembly Instructions ..................... 5
Table Assembly Pictures ………..….…….. 6, 7, 8
www.WarriorTableSoccer.com 2 | Page

Parts Identifier
Box 1
A. Side panels (2)
B. Assembled rods (8),Bearing Halves (16), Bearing Nuts,(8)Rod guards (8)
C. Balls (2), Extra Men (2), Bearing wrench (1) Silicone
Box 2
A. Leg panels (2)
B.
C. Top Panels (2)
Box 3
A. Table top (1)
B.
Leg levelers (4)
C.
Ball Catch (1)
D. Score beads (2)
E. Corner insert (4)
F. Ball Return Tube (2)
G. Metal Plate (2)
H. Bolts & washers (all nuts pre-installed in cabinet)
I. Allen wrench with Phillips head.
If you have missing parts please call 866-436-6722 extension 6803
www.WarriorTableSoccer.com 3 | Page
D.
Goal boxes (2)
White PVC Collars(4)

Hardware Identifier
Description Qty Purpose
5/16” x 1 ¾” 14 (8) Side Panels / Legs,
(6) Play Field
1/4" x 1 ¾” 14 (4) Corner Blocks
(4) Goal Boxes
(2) Ball Catch
(4) Top Plate
3/16” x 1 ½” 4 (4) Score Beads
If purchased with light bracket
1/4” x 1 ¾” 4 (4) Light Bracket
www.WarriorTableSoccer.com 4 | Page

Table Assembly Instructions
Note: No additional tools required for assembly.Nutsarepre-installed in the table. It is
recommended to get allbolts “Started” only. After bolts have been started check alignment of“top
plates”, “leg panels” & “side panels” before tightening bolts completely. No Impact/Power tools.
1. Attach Leg Leveler to legs by twisting in clockwise direction until they are all the way in.( do
not over-tighten)then standboth legs in upright position.
2. Position both side panels (2) on each side of the leg panels (make sure the 5 pre-drilled holes
are on the top ), using (8) 5/16” x 1-3/4”bolts with washers attach side panels to leg panels
(Do not tighten yet)
3. Attach goal boxes (2), using (4) 1/4”x 1-3/4”bolts and washers.
4. Insert metal plate into precut slots in goal box.
5. Attach ballcatch (1) using (2) 1/4” x 1-3/4”bolts with washers.
6. Install ball return runners (2)
a. Attach White PVC Collar to box and slide Ball Return Tube on to white collar
b. Make sure runner completely covers the collar
c. Install White PVC Collars into ball catch
d. Slide Ball Return Tube runner completely over ball catch collars
7. Place table top onto cabinet and secure using (6) 5/16” x 1-3/4” bolts with washers.
(Do not tighten yet)
8. Loosely attach corners blocks (4) to side of table using (4) 1/4” x 1-3/4” bolts with washers
(Align all side panels to legs and tighten all bolts securely.)
9. Attach topplate (2) using (4) 1/4” x 1-3/4”bolts.
10. Attach score beads (2) on to top plate using (4) #10 x 1-1/2”bolts.
11. Guide handle through opening in near wall in proper position. Pull all the way in to allow other
end of rod to clear far wall.
12. Take 2 bearing halves (marked #1 and #2) and connect them over rod on both sides and then
place them into wall by aligning tabs with openings in the side of wall opening.
13. On handle side install bearing nut and tighten fully
14. On rod exit side install Rod Guard Bearing and tighten fully
15. Repeat for remaining rods
www.WarriorTableSoccer.com 5 | Page
ROD and Guard Locations (view picture on cover for refrence)
1 man goalie rods use 10" rod guard and are closest to goal
2 man rods use 15" rod guard and are second rod from goal
5 man rods use 5" rod guard and are in the middle position of table
3 man rods use 10" rod guards and are furthest from goal
Wipe down all rods and place one or two drops of silicone on each side near bearing rotate and
slide rod into bearing to distribute silicone inside bearing
Adjust leg levelers by rotating clockwise to raise and counter clockwise to lower

Assembly Pictures
1. Install Leg Leveler by turning clockwise
into bottom of legs. Turn all the way into
the lowest point in leg.
2. Leg Panels w/ 1 Side Panel
3. Attach Goal Box and collar 4. Insert Metal Plate
5. Attach Ball Catch 6a – install ball return runner to goal box
collar
www.WarriorTableSoccer.com 6 | Page

Assembly Pictures
6b– Install runner completely over collar 6c– Install collars into ball catch
6d– Install runner completely over collars 7.Place tabletop into cabinet
8.Install Corner Block with black finished
sides exposed as shown 9.Attach Top Plate
www.WarriorTableSoccer.com 7 | Page

Assembly Pictures
10.Attach Score Beads to Top Plate
11.Guide handle through opening in near
wall in proper position. Pull all the way in
to allow other end of rod to clear far wall.
12.Take 2 bearing halves (#1 and #2) and
connect them over rod and then place them
into wall by aligning tabs with openings in
the side of wall opening.
13.Slide bearing nut over handle & tighten
14.On rod side install Rod Guard Bearing
and tighten fully
Wipe rods down with cloth ornapkin
then add 1or2 drops of silicone Level table byturning leg levelers to
raise orlower legs as needed
www.WarriorTableSoccer.com 8 | Page

Notes:
www.WarriorTableSoccer.com 9 | Page