Wasp B2000 User manual

B2000
Installation Guide

© 2012 by Wasp Barcode Technologies. All rights reserved.
No part of this publication may be reproduced or used in any form, orby any electrical or mechanical means, without
permission in writing from Wasp Barcode Technologies. This includes electronic or mechanical means, such as photocopying,
recording, or information storage and retrieval systems. The material in this manual is subject to change without notice.
The software is provided strictly on an “as is” basis. All software, including firmware, furnished to the user is on a licensed
basis. Wasp Barcode Technologies grants to the user a non-transferable and nonexclusive license to use each software or
firmware program delivered hereunder (licensed program). Except as noted below, such license may not be assigned,
sublicensed, or otherwise transferred by the user without prior written consent of Wasp Barcode Technologies. No right to
copy a licensed program in whole or in part is granted, except as permitted under copyright law. The user shall not modify,
merge, or incorporate any form or portion of a licensed program with other program material, create a derivative work from a
licensed program, or use a licensed program in a network without written permission from Wasp Barcode Technologies. The
user agrees to maintain Wasp Barcode Technologies’ copyright notice on the licensed programs delivered hereunder and to
include the same on any authorized copies it makes, in whole or in part. The useragrees notto decompile, disassemble,decode,
or reverse engineer any licensed program delivered to the user or any portion thereof.
Wasp Barcode Technologies reserves the right to make changes to any software or product to improvereliability, function, or
design.Wasp Barcode Technologies does notassume any productliability arising out of, or in connection with,theapplication
or use of any product, circuit, or application described herein. No license is granted, either expressly or by implication,
estoppel, or otherwise under any Wasp Barcode Technologies, intellectual property rights. An implied license only exists for
equipment, circuits, and subsystems contained in Wasp Barcode Technologies products.
Wasp Barcode Technologies is a registered trademark of Wasp Barcode Technologies. Other product names mentioned in this
manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged.
Wasp Barcode Technologies
1400 10th St.
Plano TX 75074
http://www.waspbarcode.com

i
B2000 Installation Guide
Table of Contents
Installation Notice................................................................................................................1
Chapter 1: Device Overview................................................................................................2
1.1 System Configuration...............................................................................................2
1.2 Device Interface .......................................................................................................3
Chapter 2 – Device Installation and Wiring........................................................................6
2.1 Wall Mounting ..........................................................................................................6
2.2 Communication Connection......................................................................................6
2.4 Power Connection....................................................................................................7
2.5 Test After Installation ................................................................................................7
Chapter 3 - Date/Time..........................................................................................................8
Appendix I – Troubleshooting...........................................................................................10
Appendix II – WiFi Function..............................................................................................11
Appendix III – Environmental-Friendly Use Description..................................................12

1
B2000 Installation Guide
Installation Notice
This device was manufactured following China, USA and EU manufacture and inspection specifications. Read this
document carefully to ensure proper use and installation of the device. Incorrect installation may damage the unit.
1. Prior to installation, make sure you have turned off the power supply. Accidental contact of the power
cable during installation can damage the device.
2. Connect the power cable after all other wiring is completed. If the device is not working properly after
installation, turn off the power first, then make changes. Any damage done to thedevice by installing it while
powered on is not covered under the warranty.
3. Make sure you do not install or operate the device where there is very strong light. Intense light will adversely
impact the fingerprint sensor’s ability to accurately read fingerprints. The device is designed for indoor use.
If it must be installed outdoors, protect it with an all-weather protective covering.
4. The device’s operating temperate range is 0° to 40° C (32° to 105° F). Do not operate the device in very hot
environments. Keep the device away from direct heat sources and provide adequate ventilation to prevent
the device from overheating.
5. The height at which you should mount the device is between 4 and 5 feet.
6. After installing, please run the auto-test function on the device to confirm the installation is completed.
7. This device has an auto-sleep and wake up function set by default. After installation, please review the
default settings and make any changes as needed.
8. We recommend using the supplied 12V DC 1.5 amp power source for the device. Using a power source
other than that supplied may cause damage to the device. Any damage caused by using a different power
source is not covered under warranty.
9. Improper wiring may cause the B2000’s main circuit board and fingerprint sensor toburn out. Resulting
damage from improper wiring is not covered under manufacturer’s warranty.
10. Only use the supplied transformer and cord. Do not attempt extending the cord by cutting or splicing.
11. Before connecting the device please review the information in the user manual.

2
B2000 Installation Guide
Chapter 1: Device Overview
1.1 System Configuration
This device supports RS232 and TCP/IP connections to the PC.

3
B2000 Installation Guide
1.2 Device Interface
Front View:
•Led Indicator:
Status Indicator
Blinking Green Normal State
Solid Green (three seconds) Verification Successful
Solid Red (three seconds) Verification Failed
•Speaker: Plays the beep sound and voice prompts.
•Screen: Displays all visual information, including time and menu screens for operation prompts.
•Fingerprint Scanner:Used to enroll or verify user identities.
•Keyboard: Used to input information to the device or execute the menu operation.
•Power Button: The 0 key acts as the power and restart button. To power on the device, press the 0 key. To turn
off the device, press and hold down the 0 button for three seconds.
Speaker
Screen
Fingerprint Scanner
Keyboard
Power Button

4
B2000 Installation Guide
Back View:
•Power Supply: Use to connect to the power supply.
•Ethernet Port: Connect the device to the Internet or connect directly to the PC.
•Wiring Terminals: Use to connect with RS232 communication (or connect with the printer).
Note: You cannot use RS232 communication and connect to a printer at the same time.

5
B2000 Installation Guide
Side View:
•USB Port – You can use the U disk to download or upload user information and verification records.
•Reset Function – If the device is not working properly, you can use the Reset function to restart it. To reset,
open the black rubber cap, then use a sharp tool (less with 2mm tip) into the Reset button hole.
Reset Button
USB Port

6
B2000 Installation Guide
Chapter 2 – Device Installation and Wiring
2.1 Wall Mounting
1. Separate the mounting plate from the B2000 by removing the screw at the bottom edge of the clock. Aspecial
screwdriver is supplied.
2. Determine the position of the mounting plate on the wall. The B2000 should be mounted on the external wall
of the door approximately 4 to 5 feet from the ground. After the desired position is determined, cut out an
opening (approximately 1 ½ inch x 1 ½ inch) for cables (see shadowed area on illustration below).
3. Line up the opening of the mounting plate with the newly cut-out opening on the wall, then screw the plate to
the wall.
4. After installation, make sure the mounting plate is tightly secured to the wall.
2.2 Communication Connection
The B2000 can directly connect with a PC through RS232 or Ethernet:
The B2000 can connect with a PC through RS485 network:
The B2000 can connect with a PC through Ethernet network:

7
B2000 Installation Guide
2.4 Power Connection
This device is powered by 12VDC. A12V power supply adapter is provided with the device. Plug the 12V power
supply into the power port at the back of the device (see section 1.2).
2.5 Test After Installation
After installation is complete, perform a test of functionality.
1. Power on the device using thepower button (see section 1.2). The green LED should begin to glow.
2. Press the Mkey to enter the device Main menu.
3. Use the arrow keys to highlight Auto Test, then press the M key.
4. Highlight All Test, then press the Mkey.
5. After the test is complete, press ESC to return to the Main Menu. Highlight User Mng and press the Mkey.
6. Enroll a new user and card (see the B2000 User Manual for details). Test the device by swiping the card.
7. If the card is not read correctly, delete the enrolled user and card and check the installation procedures. Refer
to Appendix I – Troubleshooting for assistance.

8
B2000 Installation Guide
Chapter 3 - Date/Time
This screen allows you to manually set the date and time.
1. On the Main menu, highlight the Date/Time icon and press the Mkey.
The DateTime screen appears:
2. Use the up and down arrow keys to put your cursor in the desired field.
3. Use the right and left arrow keys to set the date (year, month and date) and/or time (hour, minute and second).
4. Use the right and left arrow keys to select the Time Format. Options are 12 hour or 24 hour.
5. Use the right and left arrow keys to turn DLST(Day Light Savings Time) on or off. If DLSTis turned on, you
have several additional options to select:

9
B2000 Installation Guide
a. Date Mode – Use the left and right arrow keys to select how you want the date to display. Options are
MM-DD hh:mm or MM-WS-WK hh:mm.
b. Enter Start and End times. The allowed range for number of weeks (WS) is 1-6. The allowed range
for day of the wk (WK) is 0-6. 0 = Sunday, 1=Monday, etc.
6. After you have made changes, press the Mkey. A message will appear stating “Changes Saved
Successfully!”.
7. Press the Mkey to return to the Main Menu.

10
B2000 Installation Guide
Appendix I – Troubleshooting
Trouble Cause & Measure
Power LED is off Cause:
No power or lack of voltage.
Solution :
Check and examine the connection of power supply.
Measure the supply voltage, ensure that it is 12VDC.
Device is unable to connect with
PC
Cause:
Disruption in the connection.
Solution:
Make sure the RS232 or TCP/IP cable are securely connected to the clock.
When the device is powered on,
it cannot enter the main menu
Cause:
Chip-on-board is broken.
Solution:
Need to contact supplier and ask for repair.
The time display as “00:00” aft
er
restarting
Cause:
The clock battery is broken.
Solution:
Contact the reseller to replace a battery.
Keystroke without sound
Cause:
①Trouble in the buzzer, loud- speaker or circuit.
②Set the parameter button beep to “N” in the device
Solution:
①Need to replace the buzzer and loudspeaker.
②Enter the Menu - Options-System Opt - Adv Option - Button Beep, turn the
parameter to “Y”

11
B2000 Installation Guide
Appendix II – WiFi Function
This device has included WiFi functionality. WiFi modules can be built-in to the device.
WiFi is a type of WLAN (wireless local area network) that uses the 802.11b specification. The biggest advantage of
WiFi is the high speed of wireless transmission, which is up to 11 Mbps. WiFi is compatible with most 802.11 DSSS
devices. IEEE 802.11b wireless networking specification is a variant of IEEEE 802.11. The maximum bandwidth is
11 Mbps. If the signal is weak or there is interference, the bandwidth can adjust to 5.5Mbps, 2Mbps or 1Mbps. The
automatic bandwidth adjustment can protect network stability and reliability effectively.
The main features are: high speed, high reliability, communication distance up to 305 meters in open areas, and
communication distance of 76 to 122 meters in closed areas. WiFi is convenient, and network costs are lower than in
existing wired Ethernet.

12
B2000 Installation Guide
Appendix III – Environmental-Friendly Use
Description
The Environment Friendly Use Period (EFUP) marked on this
product refers to the safety period of time in which the product is
used under the conditions specified in theproduct instructions
without leakage of noxious and harmful substances.
The EFUP of this product does not cover the consumable parts
that need to be replaced on a regular basis such as batteries and
so on. The EFUP of batteries is 5 years.
Names and Concentration of Toxic and Hazardous Substances or
Elements
Parts Name Toxic and Hazardous Substances or Elements
Pb Hg Cd Cr6+ PBB PBDE
Chip resistor × ○○○○○
Chip capacitor × ○○○○○
Chip inductor × ○○○○○
Chip diode × ○○○○○
ESD
components
× ○○○○○
Buzzer × ○○○○○
Adapter × ○○○○○
Screws ○○○× ○○
○: Indicates that this toxic or hazardous substance contained in all of the
homogeneous materials for this part is below the limit requirement in
SJ/T11363-2006.
×: Indicates that this toxic or hazardous substance contained in at least
one of the homogeneous materials for this part is above the limit
requirement in SJ/T11363-2006.
Note: 80% of the parts in this product are manufactured with
non-hazardous environment-friendly materials. The hazardous substances
or elements contained cannot be replaced with environment-friendly
materials at present due to technical or economical constraints.