Wasserstein Solar Panel For Ring Video Doorbell 1 User manual

Solar Panel
User Manual
For Ring Video Doorbell 1 (2nd Gen, 2020 Release)

Table of Contents
Page 1 - 5
Need help? Send us an email at: [email protected]
Package Includes 2
Safety Information 2
Pre- Installation 2
Installation 2
Mounting the Solar Panel 3
Detaching the Doorbell 3
Installation Tips 3
Troubleshooting 4
Specications 4

Package Includes
Safety Information
Page 2 - 5
Need help? Send us an email at: [email protected]
．1 x Solar Panel (with Micro USB Cable)
．4 x Thinner Screws (for mounting braket)
．4 x White Wall Anchors (for mounting bracket)
．2 x Thicker Screws (for solar panel mount)
．2 x Yellow Wall Anchors (for solar panel mount)
．1 x Solar Panel Mount
．1 x Mounting Bracket
．1 x Manual
∙ Disassembling the solar panel is not recommended as it may cause damage to
internal components. The solar panel may not function properly after disassembly.
∙ Do NOT leave bare wires exposed outside the wall canopy enclosure.
Pre- Installation
1. Before setup, please ensure that the Ring Video Doorbell 1 (2nd Gen, 2020 Release)
is fully charged.
Installation
2. Connect the micro USB charging cable
from the Solar Panel to the doorbell.
Press in rmly.
1. Remove the backplate from your Ring
Video Doorbell.
White Wall
Anchors
Yellow Wall
Anchors
Thicker
Screws
Mounting
Bracket
Solar Panel
Micro USB Cable
Solar Panel Mount
Thinner
Screws

Page 3 - 5
Need help? Send us an email at: [email protected]
3. Install the included mounting
bracket onto the wall using the
thinner screws and the white wall
anchors provided.
5. Fasten the screws (that come
with the doorbell) at the bottom
of the doorbell.
4. Attach the doorbell with the connected
charger to the mounting bracket. Make
sure that the cable is tucked in the
opening designated for the cable to
pass through.

Page 4 - 5
Need help? Send us an email at: [email protected]
Mounting the Solar Panel
Important Tips
You can mount your device directly onto
wood using the included two thicker
screws. If you are mounting onto brick,
concrete, or stucco, mark the holes rst
using the bracket, drill a hole for the yellow
anchors. You can then insert the anchors
and subsequently use the screws to secure
the mount.
The amount of energy that the solar panel can produce is determined by sunlight
exposure, weather conditions, etc. To maximize the power generated by
your solar panel, please do the following:
Troubleshooting
1. I am not sure if my Ring Video Doorbell 1 (2nd Gen, 2020 Release) is being
charged.
In the presence of sunlight, there will be a light ickering on Ring Video Doorbell 1
(2nd Gen, 2020 Release) to show that it is being charged. However, at other times, it
may not icker. In such cases, please check your Ring App to view the battery status
of your Doorbell 2nd Generation.
2. It does not charge my Ring Video Doorbell 1 (2nd Gen, 2020 Release).
Please check your Ring App to ensure it's being charged and not just rely on
the Ring Light indication.
Make sure that your solar panel is pointed toward the sun and is not obstructed by
trees, buildings, or other obstacles.
∙ Choose the best location for your solar panel to get maximum sunlight exposure
throughout the day.
∙ Clean the surface of the solar panel regularly to remove any collected dust which
otherwise might aect the energy conversion.

Page 5 - 5
Need help? Send us an email at: [email protected]
Specication
∙ Material : ABS + PC
∙Power : 2.5W
∙ Output Voltage : 5V
∙ Solar panel size : 7.9 x 5.6 x 0.5 inches (200 x 142 x 13mm)
∙ Cable length : 13.1ft (4m)
Ring Video Doorbell 2nd Generation not included.
Wasserstein is a trademark of Dropcases Ltd.
Wasserstein is not aliated with Ring, Inc.
Ring Video Doorbell 2nd Generation is a trademark of Ring, Inc.
For more information, please visit:
www.wasserstein-home.com
or contact us at:
[e-mail]
Made in China