Wasserstein R03 User manual

Solar Panel
User Manual
For Eufy Video Doorbell 2K (Battery-Powered)

Table of Contents
Page 1 - 4
Need help? Send us an email at: [email protected]
Package Includes 2
Safety Information 2
Pre- Installation 2
Installation 2
Mounting the Solar Panel 3
Detaching the Doorbell 3
Installation Tips 3
Troubleshooting 4
Specications 4

Package Includes
Safety Information
Page 2 - 4
Need help? Send us an email at: [email protected]
∙ 1 x Solar Panel (with Micro USB Cable)
∙ 4 x Screws
∙ 4 x Wall Anchors
∙ 1 x Solar Panel Mount
∙ 1 x Backplate
∙ 1 x Manual
∙ Disassembling the solar panel is not recommended as it may cause damage to
internal components. The solar panel may not function properly after disassembly.
∙ Do NOT leave bare wires exposed outside the wall canopy enclosure.
Pre- Installation
1. Before setup, please ensure that the Eufy Video Doorbell 2K is fully charged.
2. If you have previously installed Eufy Doorbell, please remove it and unmount any
mount or backplate installed
Installation
1. Connect the micro USB charging cable to the Eufy Doorbell. Press in rmly.
2. Mount the backplate on the wall by the anchors and screws with the USB cable
opening at the bottom.
3. Install the Eufy doorbell on the backplate by snapping it on.
4. Make sure the cable is tucked through the opening.
5. Push the doorbell towards the backplate until you heard a "click" sound.
6. If it doesn’t sit properly or you don’t hear a click, re-check that you’ve fully tucked
any excess wire back into the hole.
7. After the doorbell is rm in its position, switch it on and it is ready for use or
installation if you have not set it up yet.
Wall Anchors
Backplate
Solar Panel
Micro USB Cable
Solar Panel Mount
Screws
1 2 3 4 5

Page 3 - 4
Need help? Send us an email at: [email protected]
Mounting the Solar Panel
Detaching the Doorbell
Important Tips
You can mount your device directly onto
wood using the included screws. If you are
mounting onto brick, concrete, or stucco,
mark the holes rst using the bracket, drill a
hole for the anchors.You can then insert the
anchors and subsequently use the screws
to secure the mount.
1. Use the doorbell detaching pin and insert it into the pin hole at the bottom of the
backplate if you wish to detach the doorbell from the backplate.
2. Insert and press the pin in the hole at the bottom of the doorbell.
3. After the backplate has been loosened from its rm position via the pin insertion,
you can lift it o and remove it from the doorbell camera.
The amount of energy that the solar panel can produce is determined by sunlight
exposure, weather conditions, etc. To maximize the power generated by
your solar panel, please do the following:
∙ Choose the best location for your solar panel to get maximum sunlight exposure
throughout the day.
∙ Clean the surface of the solar panel regularly to remove any collected dust which
otherwise might aect the energy conversion.

Page 4 - 4
Need help? Send us an email at: [email protected]
Specication
∙ Material : ABS + PC
∙Power : 2.5W
∙ Output Voltage : 5V
∙ Solar panel size : 7.9 x 5.6 x 0.5 inches (200 x 142 x 13mm)
∙ Cable length : 13.1ft (4m)
Troubleshooting
To troubleshoot problems with your Eufy Video Doorbell 2K (Battery-Powered)
Solar Panel
1. Unplug and re-insert both ends of the solar panel charging cable.
To unplug the charging cable and reinsert it into the solar panel, you must squeeze
the sides of the plug. The sides of the plug click into place when the plug is fully
inserted into the solar panel.
2. Make sure that your solar panel is pointed toward the sun and is not obstructed by
trees, buildings, or other obstacles.
Eufy Video Doorbell 2K (Battery-Powered) not included.
Wasserstein is a trademark of Dropcases Ltd.
Wasserstein is not aliated with Anker Innovation, Inc.
Eufy Video Doorbell 2K (Battery-Powered) is a trademark of Anker Innovation, Inc.
For more information, please visit:
www.wasserstein-home.com
or contact us at:
[e-mail]
Made in China