WaterUps Oasis 1680 User manual

Oasis 1680
Scan the
QR Code to go
to the website
Watch the full assembly video for your Self-Watering
Wicking Bed Kit on the Waterup Website.
www.waterups.com.au/product/waterups-oasis-1680-wicking-bed
Watch the full assembly video for assembling the water reservoir
on our website:
www.waterups.com.au/product/waterups-oasis-1680-wicking-bed
1: Take the liner and fold the ends as shown in the video.
2: Push the three tabs in the corners from the outside in and repeat
the enre process for the next three corners, creang the square
base liner.
3: Place the liner inside the planter, make sure the hole in the liner
and the hole in the planter match up.
4: Take one of your cells and the overow pipe and assemble as
shown in the video.
5: Feed the le and the overow pipe through the hole in the
reservoir and the planter and ensure it sits at in the boom of the
reservoir. Replace the spacer on the overow pipe and ghten the
nut.
6: Place the next 6 cells into the boom of the planter.
6: Take the last le and the inlet pipe. With a sharp knife remove the
circle in the le along the line as indicated in the video.
7: Insert the inlet pipe into the le. Take note of the three tabs on
the inlet pipe that will t through the three holes in the le. Apply
some pressure unl it clicks in.
8: Insert this le in the end of the planter. Decide if you want the
inlet at the side or back.
For suggesons about soil for wicking beds and other relevant
informaon visit our website.
This informaon booklet is printed on recycled paper.
Please compost or recycle this when you are nished.
Before you start
Assembly of the Water Reservoir and Tiles
Filling your Planter
www.waterups.com.au |Email: [e-mail] |Phone: [phone]
by
Self-Watering Wicking Bed Kit

D
E
F
C
1 2 3 4
B
A
3 2 1 5
C
D
4 6 7 8
A
B
800 X 1600 PLANTER
A3
SHEET
2 OF 4
NOT TO SCALE
DWG. NO.
TITLE:
REVISION
DATE:
13-07-21
DRAWN BY:
MH
Water Wix Pty Limited
0-17-1
www.waterups.com.au
SHEET SIZE
5 6
E
c 2021
• No. 2 Phillips Head Screw Driver
• Sharp Knife
• Around 3m2of ground to build on
What You
Will Need
Assembly of the Metal Planter
D E F C
1
2
3
4
B A
3
2
1
5
C D
4
6
7
8
A B
400 X 1200 PLANTER
A3
SHEET
1 OF 4
NOT TO SCALE
DWG. NO.
TITLE:
REVISION
DATE:
19-07-21
DRAWN BY:
MH
Water Wix Pty Limited
0-02
www.waterups.com.au
SHEET SIZE
5
6
E
c 2021
1: Assemble the Boom Rails by inserng and ghtening screws rst in the
corner brackets and then join both ends with the connector rails. Then ip
the enre Boom Rail assembly over
2: Correctly posion the corner panels so the short side is at the end.
Insert and fasten screws to connect the Corner Panel to the Boom Rail
Assembly
3: Insert the Side Panels - there are two sizes, a long and short. On the long
panel one of the ridges has an extra kink in it. This kink needs to go to the
centre of the side panel. Also insert a panel into the two ends.
4: Fit the End Top Rail. Make sure the long edges are on the inside.
5: Fit the Side Rails ensureing that the corner bracket ts over the end rail
and that the holes line up.
6: Place the two connector rails and insert and ghten screws to complete
the top rail assembly.
7: Insert and ghten screws to secure the enre Top Rail assembly to the
rest of the planter.
D
E
F
C
1 2 3 4
B
A
3 2 1 5
C
D
4 6 7 8
A
B
800 X 1600 PLANTER
A3
SHEET
1 OF 4
NOT TO SCALE
DWG. NO.
TITLE:
REVISION
DATE:
13-07-21
DRAWN BY:
MH
Water Wix Pty Limited
0-17-1
www.waterups.com.au
SHEET SIZE
5 6
E
c 2021
Boom Rails
Side Panels
Side Panels
Top Rails
Connector Rail
Connector Rail
Corner Panel
Corner Bracket
End Panel
Railing long
edges are
always on the
inside
Ensure short
side of corner
panel is at
the end