wattstopper DT-355 User manual

DT-355
360°DualTechnology•LineVoltage
Occupancy Sensor
with Light Level feature
SPECIFICATIONS
Voltages ...................120/230/277/347VAC, 50/60Hz
Load Requirements
@120VAC, 50/60Hz ........... 0-800W Ballast/Tungsten
@230 or 277VAC, 50/60Hz .............0-1200W Ballast
@347VAC, 50/60Hz ...................0-1500W Ballast
Operating Temperature ..........32° to 131°F (0° to 55°C)
Terminal Torque Rating ... 4.428 inch pound-force. (0.5Nm)
Light Level One-Step Adjustment ............ 10FC–300FC
Time Delay Adjustment...................5 to 30 minutes
Walk-Through Mode .3 minutes if no activity after 30 sec.
Test Mode5 sec. upon intial power-up or DIP switch reset
PIR Coverage (Typical) .........................1200 ft2
Sensitivity Adjustment..............................
............Automatic or Low (DIP switch setting)
Ultrasonic Coverage (Typical) ............... 800-1200 ft2
Sensitivity Adjustment...Minimum to Maximum (trimpot)
Frequency ...................................40kHz
Installation Instructions
U.S. Patents: 5,189,393
and Patent Pending

UNIT DESCRIPTION
The WattStopper DT-355 360° Dual Technology occupancy sensors combine
advanced passive infrared (PIR) and ultrasonic technologies into one unit. The
combination of these technologies helps to eliminate false triggering problems
even in difficult applications.
The DT-355 turns lighting systems on and off based on occupancy and ambient
light levels. The light level feature can be used to keep lights from turning on if
the ambient light level is sufficient.
SmartSet™ technology allows the sensor to be installed with minimal
adjustments. SmartSet automatically adjusts the time delay and PIR sensitivity
to usage patterns in the controlled space.
The DT-355 offers numerous operating modes that can be combined to create
the ideal custom control. The sensors can be configured to turn lighting on,
and hold it on as long as either or both technologies detect occupancy. After no
movement is detected for the user-specified time or the SmartSet time (5 to 30
minutes) the lights are switched off. A “walk-through” mode can turn lights off
after only 3 minutes, if no activity is detected after 30 seconds of an occupancy
detection.
The DT-355 operates on 120VAC, 230VAC, 277VAC, or 347VAC line voltage.
COVERAGE PATTERN
The DT-355 provides a 360° coverage pattern. The coverage shown represents
walking motion at a mounting height of 10 feet. For building spaces with lower
levels of activity or with obstacles and barriers, coverage size may decrease.
Call 800.879.8585 for Technical Support
44 ft
(13.4m)
40 ft x 40 ft
(12.2m x 12.2m)
Drawings not to scale.
Ultrasonic
Coverage
PIR
Coverage

PLACEMENT GUIDELINES
Depending upon obstacles such as furniture or partitions, the area of coverage
may be less or more than the sensing distances shown in the coverage pattern.
This must be considered when planning the number of sensors and their
placement. It is also recommended to place the sensor 4 to 6 feet away from
air supply ducts. Mount the sensor to the ceiling. The DT-355 is designed for
a ceiling height of about 8-10 feet. Mounting above or below this range will
significantly affect the coverage patterns. As a general rule, each occupant
should be able to clearly view the sensor.
Masking the PIR Lens: Opaque adhesive tape is supplied so that sections of
the PIR lens can be masked. This restricts the sensor’s view and allows you
to eliminate PIR coverage in unwanted areas such as hallways outside of the
desired coverage area. Since masking removes bands of coverage, remember
to take this into account when troubleshooting coverage problems. The
Ultrasonic coverage cannot be masked, but you can adjust its sensitivity to
reduce the coverage area.
Open Office Area Coverage: To get complete coverage in an open office area,
install multiple sensors so that there is approximately 20% overlap with each
adjacent sensor’s ultrasonic coverage area.
Visit our website for FAQs: www.wattstopper.com
Ultrasonic
Coverage
40 ft
(12m)
PIR
Coverage
44 ft
(13.4m)
20%
Ultrasonic
Overlap

WIRING DIRECTIONS
Visit our website for FAQs: www.wattstopper.com
Load
Load Hot
Neutral
Neutral
Ground
(Optional)
Hot
Neutral
Neutral
Load
Load
Load
Line
Neutral
Line
Ground
(Optional)
Ground
(Optional)
Three-way wiring
Single sensor, single load
Strip Gauge
#12 to #16 AWG
Cu Wire Only
WARNING
TURN POWER OFF AT THE CIRCUIT BREAKER
BEFORE INSTALLING SENSORS.

Call 800.879.8585 for Technical Support
LIGHT LEVEL FEATURE
The Light Level feature holds lights off upon initial occupancy if adequate
ambient light exists. It will not turn the lights off if they are on. The default
setting is for maximum, meaning that even the brightest ambient light will not
hold the lights off. When the light level is set it is written to memory so that in
the event of a power failure the setting is not lost.
• Avoidmountingthesensorclosetolightingfixtures.
• Adjustduringdaylighthourswhenambientlightintheareaisatdesired
level.
1. Open the Front Cover and locate the Light Level pushbutton. See Sensor
Adjustment.
2. Momentarily press the Light Level pushbutton. Do not exceed 4 seconds. *
The sensor enters setup mode, as indicated by the rapidly flashing Red LED.
The LED will flash throughout the setup process. Occupancy indications from
the LEDs are disabled during setup.
3. Move away from the sensor to avoid interference with light level detection.
The sensor measures the light level for a 25-second period, then averages
the readings and automatically sets the light level function.
4. When the Red LED stops flashing, replace the Front Cover.
* Pressing the pushbutton for 5 seconds or more resets the light level to the
default. The Green LED flashes rapidly for 10 seconds after the setting has
changed.

Using a 4-Inch Square
Junction Box
1. Pull the high voltage wires into
the J-Box through the conduit
knockout.
2. Run the wires through the CA-1
adapter then connect the high
voltage wires to the appropriate
terminals on the sensor.
3. Align the CA-1 and the sensor
with the J-Box so that the
mounting screw tabs on the box
match the mounting holes on the
sensor’s rear housing and the
CA-1.
4. Use two machine screws (included
with the sensor) to attach the sensor
to the mounting tabs on the J-Box.
5. Snap the front cover onto the sensor.
Using an Octagonal Junction Box
1. Pull the high voltage wires into the
J-Box through the conduit knockout.
2. Connect the high voltage wires to the
appropriate terminals on the sensor.
3. Align the sensor in the
J-Box so that the mounting
screw tabs on the box
match the key holes on the
sensor’s rear housing.
4. Use two machine screws
(included with the J-Box)
to attach the sensor to the
mounting tabs on the J-Box.
5. Snap the front cover onto
the sensor.
Call 800.879.8585 for Technical Support
Rear Housing
4" Square
Wiremold #V5752 box
Front Cover
Ceiling
Screws
CA-1 Adapter
Sensor Flange
MOUNTING THE SENSOR
4" Octagonal, 2.25" Deep*
Junction Box
Ceiling
Sensor
Screws
Front
Cover
Mounting to an Octagonal Junction Box
Mounting to a 4” Square Wiremold V5752
box or 4” Square Junction Box with
Double-Gang Mudring
* The Junction Box must be at
least 2.25” deep. If it is not, an
extension ring is required.

SENSOR ADJUSTMENT
The sensors are factory preset to allow for quick installation in most
applications. Verification of proper wiring or coverage, or customizing the
sensor’s settings can be done using the following procedures. To make
adjustments, open the Front Cover with a small screwdriver.
There is a 30 second
warm-up period when
power is first applied.
Before making
adjustments, make sure
the office furniture is
installed, lighting circuits
are turned on, and the
HVAC systems are in the
overridden/on position.
VAV systems should be set
to their highest airflow.
Set the Logic Configuration
and Time Delay to the
desired settings. See “Logic Configuration Chart”, next page.
To Test Occupancy Sensors
1. Ensure the PIR and Ultrasonic Activity LEDs are enabled (DIP switch 7 ON)
and PIR Sensitivity is set to MAX (DIP switch #8 ON).
2. Ensure the Time Delay is set for Test Mode* using the “5 seconds/SmartSet”
setting. (DIP switches 4, 5, & 6 are OFF).
3. Ensure that the Light Level is at default (maximum). See the Light Level
Feature section of this document for instructions.
4. Ensure that the Ultrasonic Sensitivity trimpot is set to about 90%, clockwise.
5. Remain still. The red and green LEDs should not flash. The lights should
turn off after 5 seconds. (If not, see “Troubleshooting.”)
6. Move about the coverage area. The lights should come on. Adjust the
Ultrasonic Sensitivity as necessary to provide the desired coverage (Green
LED indicates activation from the ultrasonic sensor).
When testing and adjustment is complete, reset DIP Switches and Light Level to
the desired settings, and replace the cover on the sensor.
* If you need to invoke the Test Mode and the DIP switches are already set for
5seconds/SmartSet, toggle DIP switch #5 ON then back to the OFF position.
This provides a 5 minute test period. During the test period, the Time Delay
is only 5 seconds.
Keyhole slots
(for mounting to
4" octagonal box)
Double gang
mudring
mounting holes
Light level pushbutton
DIP switches
PIR lens
Ultrasonic
sensitivity
trimpot
ON
12345678
ECE
Ultrasonic
transducer
cones
Ultrasonic
activity
LED (Green)
PIR Activity
LED (Red)
Call 800.879.8585 for Technical Support

OCCUPANCY LOGIC
The DT-355 has 6 logic configurations for
occupancy triggers, set with DIP switches 1,
2 & 3. Determine the appropriate Occupancy
Logic Option using the Trigger matrix, then set
the DIP switches accordingly.
Initial Occupancy: The method that activates a
change from “Standby” (area unoccupied and
loads are off) to “Occupied” (area occupied and
loads are on).
• Both requires motion detection by the PIR
and the Ultrasonic.
• Either requires motion detection by only one
technology.
• PIR requires motion detection by the PIR.
• Ultra requires motion detection by the
Ultrasonic.
Maintain Occupancy: The method indicating
that the area is still occupied and the lights
should remain on.
Re-trigger: After the time delay elapses and
the lights turn off, detection by the selected
technology within the number of seconds
indicated turns the lights back on.
Logic Configuration Chart
8
Minimum
Max./SmartSet
PIR Sensitivity
5 sec/SmartSet
10 min.
10 minutes
15 min.
15 minutes
20 minutes
30 min.
5 minutes
456
Time Delay
= walk-through mode
LEDs
Disabled
Enabled
7
= ON
– = OFF
Standard
Option 2
Option 3
Option 1
123
Option 4
Option 5
Logic
Switch#
Occupancy
Standard
Option 2
Option 3
Option 1
Trigger
Option 4
Option 5
Initial
Occupancy
Maintain
Occupancy
Re-trigger
(seconds
duration)
Occupancy Logic
Both
Both Both Both(5)
Either(n/a)
Either
EitherEither
Either
Either(n/a)
Either(n/a)
PIR
PIR
PIR PIR(5)
Ultra(5)
Ultra Ultra
= Factory Setting




Visit our website for FAQs: www.wattstopper.com

Visit our website for FAQs: www.wattstopper.com
Time Delay: Switches 4, 5, 6
The sensor will hold the lights on as long as occupancy is detected. The time
delay countdown starts when no motion is detected. After no motion is detected
for the length of the time delay, the sensor will turn the lights off. The sensor
can select the time delay using SmartSet, or you can select a fixed time delay.
• SmartSetrecordsoccupancypatternsandusesthishistorytochoose
an optimal time delay from 5 to 30 minutes. SmartSet behavior starts
immediately and is refined continually as history is collected.
Walk-through mode turns the lights off three minutes after the area is
initially occupied, if no motion is detected after the first 30 seconds. If motion
continues beyond the first 30 seconds, the selected time delay applies.
LEDs
When enabled, the red PIR and green Ultrasonic Activity LEDs on the sensor
will light when the associated sensor detects motion.
PIR Sensitivity
• MinimumforcesareduceddetectionrangeforthePIR.
• Max./SmartSetcausestheDT-355tomonitorthecontrolledenvironment
and automatically select the maximum sensitivity that will provide reliable
operation without false detection. This setting is constantly updated.

TROUBLESHOOTING
For any unexpected operation
1. Check DIP switch settings.
2. Make sure the switches are set according to the defined settings in the
Logic Configuration Chart.
Lights do not turn on with occupancy, and the following condition exists:
• BothLEDsdonotflash:(DIPswitch#7mustbeONtoenabletheLEDs)
1. Check that the circuit breaker has been turned back on.
2. Check all sensor wire connections.
3. Check for line voltage input to the sensor.
- If line voltage is present, replace the sensor.
- If line voltage is not present, check line wiring.
• RedLEDdoesnotflash:
When power is initially applied to the sensor, there is a warm-up period of 30
seconds before the red LED is active.
1. Make sure that PIR Sensitivity is set to 100% (DIP switch #8 set to on).
2. If it still does not flash, call 800.879.8585 for Technical Support.
• GreenLEDdoesnotflash:
1. The Ultrasonic Sensitivity setting may need to be increased.
Turn clockwise as needed.
• BothLEDsflash:
1. If the sensor’s Light Level feature has been turned on, the lights
connected to the Light Level Output might be held off because of the
level of ambient light in the controlled area. To test whether the Light
Level adjustment is the problem, cover the area around the green LED
(see diagram) with your hand to see if the lights turn on. If the lights
turn on, the Light Level setting was keeping the lights off (see, “Sensor
Adjustment” for readjustment).
2. Check all sensor wire connections.
3. Check for line voltage input to the sensor.
Lights do not turn off automatically:
Call 800.879.8585 for Technical Support
WARNING
TURN POWER OFF AT THE CIRCUIT BREAKER
BEFORE WORKING WITH OR NEAR HIGH VOLTAGE.